Hagbard Celine
Well-Known Member
Now try that with two of them at the same time
Def been thinking a lot more about this. I’ll have to start asking around for better cord management solutions on other sites as well
CouchLog
- Thread starter Chris@420Eng
- Start date
Def been thinking a lot more about this. I’ll have to start asking around for better cord management solutions on other sites as well
Vitolo
Vaporist
That cart is looking pretty great @Vitolo !
As for cord management, I think a lot of issues could be solved if there as an even better way to secure the temperature unit. The magnets are a great insight and innovation. But maybe something stronger would help for that piece in particular. Hmmm, maybe velcro?
As for cord management, I think a lot of issues could be solved if there as an even better way to secure the temperature unit. The magnets are a great insight and innovation. But maybe something stronger would help for that piece in particular. Hmmm, maybe velcro?
Vitolo
Vaporist
Thanks for that @Texus !
The cart is metal, but now I get where you are coming from. I misinterpreted your comments to address more "cord", rather than "stability & security/attachment".
A couple of additional round pads that would be an interface between a surface, and the CouchLog system.
You're thinking was a step ahead of me... and it shows that you really appreciate and put thought into convenience, and the comfortable use of your tools.
You are appreciated for the critical thinker & Vapor Aficionado that you are!
TigoleBitties
Big and Bouncy
Yep. Just got these today and they're no good for the above reasons. 🫤
Ripstar
Well-Known Member
I would imagine something similar to this, only smaller in size would help a lot:
Vitolo
Vaporist
This looks like the initial set-up with various cords might take a few minutes of patience, but would be a very comfortable situation once done!
That is 10 feet for $14.98
There are quite a few lower priced options for the same concept, made of the same exact material are many, but these 2 are the most obvious that stood out:
- 2 Meters for $1.98 no shipping charge: Temu Cable Organizer 2 Meters- $1.98
- 100 feet of the same product for $15.13: Professional Cable Control!!
Yes.
Exactly, but with the 14mm bowl (in this case referring to the male joint that goes into the bong) you would need a glass adapter to mate the 14mm male bowl to the 18mm female pipe.
The Couchlog 18mm Glass Bowl, the 14mm Glass Bowl, the standard MP and the Glass MP. The small adapter there is an 18mm to 14mm ground glass reducer.
!8mm bowl fits an 18mm female joint natively; the 14mm bowl needs the reducer to reduce from 18mm to 14mm.
The Mouthpieces are both cut to 18mm; both fit natively (they both also fit 14mm female joints natively, but the all-wood one doesn't always fit all 14mm joints, hence the glass one). In this case the glass mouthpiece will also fit with the reducer as well:
Hah! My pleasure. It's fun to watch people work it out and then dial in and really begin to enjoy it. : )
Circling back on this after a bit of a delay! Thank you so much for your help, I ended up getting the bowl and the j-hook from Vgoodiez - they are fantastic, and I am finally really enjoying the couchlog! I alternate between just using it dry with the J-hook and using it with a bong, both are great.
Question for the group: I haven't been able to find any info on how to clean the injector itself. I've been just swabbing the outside of the injector with ISO, but I can't figure out if there is a way to remove the screen and clean it properly? The screen seems very permanently stuck in there... does it even come out? And what is under the screen, will soaking the whole thing in ISO damage it?
Thank you everyone!! This forum has been so helpful <3
Is that part getting dirty? I have never attempted to clean mine and it is the same as when I bought it.
I would not recommend disassembling it, but I suppose @Chris@420Eng could verify that.
TangibleHangnail
Well-Known Member
Any feedback on the Couchlog XL? (I can't search back for XL because it's too short!) Does the XL bowl fit any ball vapes well?
this is correct. Please don't open it.
It should't get dirty inside since you only pull air through it.
nicknobody
Well-Known Member
Opposite for me. I was wondering if the XL fits any ball vape bowls such as elevate injector bowl or vgoodiez injector bowl?
Thank you.
the XL heater fits an 18mm joint.
TigoleBitties
Big and Bouncy
I have the 14mm and 18mm injector bowls from VGoodiez. The 14mm one fits my Couchlog very nicely so I would imagine the 18mm one they sell would work nicely with the Couchlog XL but I don't own the XL to actually try it.
I'm willing to accept any Couchlog XL donations to see how well it works.
On the same topic, it's my understanding that temperature controller that comes with the original 14mm Couchlog will work with the XL Couchlog but I don't see any options on the website for purchasing the Log-Only Couchlog XL. @Chris@420Eng, is this by design or did I miss something?
I took a couple of BB9 cooled/Omni tip dynavap hits off the CL yesterday using the stainless bowl as an adapter trick. Face melting goodness!
I love how versatile the CL is. Hitting it this way really feels like you're lighting the tip of a joint with a match and puffing away. Feathering the carb on the BB9 also gives a satisfying amount of temp control.
There was a code posted somewhere on here to put in when checking out to get the xl without the controller. I’m on mobile or I’d do some digging for youI have the 14mm and 18mm injector bowls from VGoodiez. The 14mm one fits my Couchlog very nicely so I would imagine the 18mm one they sell would work nicely with the Couchlog XL but I don't own the XL to actually try it.
I'm willing to accept any Couchlog XL donations to see how well it works.
On the same topic, it's my understanding that temperature controller that comes with the original 14mm Couchlog will work with the XL Couchlog but I don't see any options on the website for purchasing the Log-Only Couchlog XL. @Chris@420Eng, is this by design or did I miss something?
I took a couple of BB9 cooled/Omni tip dynavap hits off the CL yesterday using the stainless bowl as an adapter trick. Face melting goodness!
I love how versatile the CL is. Hitting it this way really feels like you're lighting the tip of a joint with a match and puffing away. Feathering the carb on the BB9 also gives a satisfying amount of temp control.
EarthworldTim
Well-Known Member
Nocontroller is the code
TigoleBitties
Big and Bouncy
I tried this on the site and it doesn't seem to work.
Works again. It hadn't been applied to the new models.
nicknobody
Well-Known Member
TigoleBitties
Big and Bouncy
I've been flirting with the idea for a little while...
