'The Misty Log' - DIY wooden Log Vaporizer
- Thread starter blokenoname
- Start date
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
Dimmer or buck converter/vvps will both do. The buck is more precise, due to the digital display. Easier to memorize the wattage/voltage than a random position on an unmarked dimmer dial.
I'd suggest looking for one with push buttons for changing the voltage. Most come with miniature style potentiometer screws though. Works fine too, but you'll always need a small screwdriver then, when changing the voltage.
I'd suggest looking for one with push buttons for changing the voltage. Most come with miniature style potentiometer screws though. Works fine too, but you'll always need a small screwdriver then, when changing the voltage.
brainiac
log wrangler
First post on NFC. Highly encouraging to see so much interest in DIY log and desktop vapes 
Been busy with other (mainly useful) stuff recently so I'm really happy to be back building logs again.
This one's an oak Rustic. It's part of a branch cut by a local farmer during routine land management.
Here's the blank prior to de-barking.
De-barked, threaded and drilled...
HC and electrics installed. Base well closed and sealed with olive green leather.
The stem is also oak but made from dowelling so it doesn't count as Rustic.
Well, back to the testing
- no rest for some of us 
Been busy with other (mainly useful) stuff recently so I'm really happy to be back building logs again.
This one's an oak Rustic. It's part of a branch cut by a local farmer during routine land management.
Here's the blank prior to de-barking.
De-barked, threaded and drilled...
HC and electrics installed. Base well closed and sealed with olive green leather.
The stem is also oak but made from dowelling so it doesn't count as Rustic.
Well, back to the testing
- no rest for some of us 
Abysmal Vapor
Supersniffer 2000 - robot fart detection device
Hey @blokenoname I have this gadet and mean to post about it here and always forget..
Actually i managed to power one small halo-coconut with it that features 20w bulb with a usb to 2.1mm cable.
Xtar PB2S QC 3.0 + PD 3.0 Portable Li-ion Charger and Powerbank (LIMITED Red LED Edition) (Red)
It can be used also as a powerbank and a charger.
Input: QC3.0 and PD3.0 (5v 2A / 9V 2A / 12V 1.5A)
Constant Current Charging 2A x 2 / 2A x 1 / 1A x 2
Charge Voltage: 4.20V +- 0.05V
Termination Current: <= 120mA
USB Output: QC3.0 and PD3.0 (5v 2A / 9V 2A / 12V 1.5A)
Operating Temperature: 0-40C
Compatible batteries: 18650 (protected and unprotected), 20700/21700 (unprotected)
Actually i managed to power one small halo-coconut with it that features 20w bulb with a usb to 2.1mm cable.
Xtar PB2S QC 3.0 + PD 3.0 Portable Li-ion Charger and Powerbank (LIMITED Red LED Edition) (Red)
It can be used also as a powerbank and a charger.
Input: QC3.0 and PD3.0 (5v 2A / 9V 2A / 12V 1.5A)
Constant Current Charging 2A x 2 / 2A x 1 / 1A x 2
Charge Voltage: 4.20V +- 0.05V
Termination Current: <= 120mA
USB Output: QC3.0 and PD3.0 (5v 2A / 9V 2A / 12V 1.5A)
Operating Temperature: 0-40C
Compatible batteries: 18650 (protected and unprotected), 20700/21700 (unprotected)
so you use dynavap screen between two mesh, but in my first build i use a piece of steel, the same of the tubing, if i put it like you became more conduction than convection or not ? if i put the dome just over the bulb and more over the screen isn't better ? i just need to know because it's more easy to put at the same level of the screen but....
Because dynavap screen are no so economic...
you have to ask @blokenoname I do not know that.
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
However you like. I've done it both ways.
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
el sargantano
Well-Known Member
Fantastic thread as always.
European log diyers union pride!
European log diyers union pride!
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
Welcome back to the old haunts 
Abysmal Vapor
Supersniffer 2000 - robot fart detection device
Here is some logvape history to celebrate it 
) !The Pneuma ! There is one unit on the first pic that looks like a TUBO/ZION hybrid,lol.. (with the stem holder)
) !The Pneuma ! There is one unit on the first pic that looks like a TUBO/ZION hybrid,lol.. (with the stem holder)
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
Finally . The 3/8" tubing arrived from China.
. The 3/8" tubing arrived from China.
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
Knickknack to make life easier... 
Power file and new tube cutter:
Power file and new tube cutter:
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
blokenoname
DIY Log Dabbler ππͺ΅πͺπ¨π¨π¨
Great to see that Rustic blank getting the full Misty treatment
And that cartridge heater should ensure that it'll mamage easily with concentrates as well as herb.
Coming along nicely
Left it unchanged, mostly. Just added the through hole and the hole for the plug and beveled the top a bit. Sanded and polished it a bit with fine grit sandpaper and steel wool and then waxed it, plugged it up and added the leather bottom.
Now it's heating up and I'll let it run for an hour or two, while taking a well deserved nap
5 bilder in einem