TinyMight / TM 2
- Thread starter kuzko
- Start date
Momor
Well-Known Member
You don't need any tool to disassemble/assemble the cooling unit if it is for that reason you're asking
Momor
Well-Known Member
I can still be misunderstanding what you want to do but you shouldn't unscrew the board from the body. On older units there was a note near that screw saying "don't screw with the screw" i think.
Also, there should be no need to unscrew the board in order to repair/reposition the haptic motor.
Sorry if I'm still off topic
Also, there should be no need to unscrew the board in order to repair/reposition the haptic motor.
Sorry if I'm still off topic
gangababa
Well-Known Member
WisePenny
unknown. unmember.
I may be wrong, but that is for the bottom one I believe. The cooling unit screw size (and bottom of board) is much smaller
Vaporific
All who wander are not lost...
A T-20 might work in a pinch too but T-15 is the optimal size - for the main screw holding the TM together. I don’t know the exact size for the CU screw but, yes, smaller than T-15.
EDIT: do not unscrew the screw on the board!!
Shorner
Well-Known Member
Is that the short one? How's the cooling/Taste compared to glass?
Are you using basket screens with it?
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Yes that is what I call the multi WPA with glass honeycomb screen, three in one, I recommend getting the 18.8 mm one that does not have the glass honeycomb screen as well, that is what I use more often (well actually I am using backwards RBT stems, but same thing) though I use the multi WPA every once in a while to try a whole nug or chunky grind for some low temp flavor hits full spectrum style interesting experience, but I always end up emptying the bowl and crushing the herbs further to load in my normal stems... So just decide what's useful to you! (Alan@toasty-top.com for 14 mm WPA if you need it)
Again you have to decide if you want it, I have one that I only use sparingly, once in awhile to mix things up, it's not as enjoyable as using with WPA and a J hook or other such dry cooling 18.8 mm female pieces that I have...
Again this is up to you how much you think you will be using the cooling unit, a spare is useful if you want to have a clean one always ready to go, but not necessary unless you are using it a whole lot?
And decide if you want extra stems or long stem, I don't use those much because I am at home using WPA and hooks etc so I can't say, but it's more useful out and about and the longer stem offers more cooling with the CU?
I have not tried their portable bubblers, I've seen some good reviews of it here in the thread along with a little negative, again this is up to you, you definitely can find better larger or smaller glass pieces with a lot more variety and using a WPA, which I like, and yes there are many suggested here and other places like the cheap glass thread, so you have to decide what you want is all!
dman28
Vaping for the health of it.
Let me explain. I received one of the earlier units with the new board. The board is the same dimension now as the base plate and looks like they did a bit of cutting to fit it.
My unit had an incorrectly installed hepatic motor, so they were to send me new components for the fix. I didn't hear from them for a few days despite a few emails, so I pulled it apart removed the motor, repositioned it and glued it.
Putting it back together I realised the board was not torqued down correctly making it very hard to place the bottom back on and align the contacts if the board is not tight! Today, I received an email the paper work for the parts sent yesterday with directions and realised I should have bent the contacts down a little further. It is working perfectly. And I guess I am going to have spare parts.
dman28
Vaping for the health of it.
No I didn't but I'll pull it apart later take a few.
condition
Well-Known Member
Just buy the main unit and a WPA (or 2) from manufacturer
After that you get your own glassware, I suggest to get and a j-hook and a water pipe (if you don't have one) from an independent seller, depending on your budget and location.
karec
Well-Known Member
I got one with 55mm, cools better than glass and i don't see difference in taste, im using 1/2 CU with 5mm ss balls with the native screen, since it cools better i took the rood out and from 1 CU now i got 2 x 1/2 CU.
Not worried anymore about breaking the glass stem and look good on the device
Cheers
I will join the chorus and also recommend you skip this one. It is my least favorite of my 7 TM stems. Not to mention how great the TM is with a WPA on other glass.
Joie de Vivre
Well-Known Member
ftr I love the easy and cool long stem and am stocking up but, horses for courses.
I was using the TM for sessions for a while, because I had been rotating it with session vapes anyway, and just now instead took one long hit that has inspired me to visit FC and report it was masterchef-level tasty. And I love the long stem.
I had said a couple of months back that my device was too hot. But I just had to let it cool down now and again.
I was using the TM for sessions for a while, because I had been rotating it with session vapes anyway, and just now instead took one long hit that has inspired me to visit FC and report it was masterchef-level tasty. And I love the long stem.
I had said a couple of months back that my device was too hot. But I just had to let it cool down now and again.
VapeArts
Lucid Dreamer
I just moved the bulk of my I received my TM post to the TM Ordering and Shipping thread.
I have a question. Included in the package is a thin stiff clear plastic tube about 3/4" long and the same width as the battery compartment top that unscrews. I have no idea what it is used for and it isn't shown on the instructions. It came wrapped in protective plastic so I assume it was intentional. It isn't something I ordered. Can someone tell me what it is for?
I have a question. Included in the package is a thin stiff clear plastic tube about 3/4" long and the same width as the battery compartment top that unscrews. I have no idea what it is used for and it isn't shown on the instructions. It came wrapped in protective plastic so I assume it was intentional. It isn't something I ordered. Can someone tell me what it is for?
Last edited:
Abysmal Vapor
Supersniffer 2000 - robot fart detection device
Cooling unit/stem storage ?
Vaporific
All who wander are not lost...
Are you sure it’s plastic? Without a pic it sounds like it could be a replacement glass cylinder for the heating chamber. There’s a glass cylinder behind the metal one where a stem is inserted. He’s known for throwing in extras and goodies; I got some too but can’t remember what they were, lol.
I got one of these with my TM months ago (did not order it). I thought that was awesome because it would be a resl drag to send it back to Finland if that inner glass tube broke.Are you sure it’s plastic? Without a pic it sounds like it could be a replacement glass cylinder for the heating chamber. There’s a glass cylinder behind the metal one where a stem is inserted. He’s known for throwing in extras and goodies; I got some too but can’t remember what they were, lol.
Anyway I bet you are right.
VapeArts
Lucid Dreamer
I believe you are correct. It’s pretty thin glass and the metal tube/sleeve from the heating chamber fits inside it perfectly. Nice to know I have that extra piece. Thanks!!!Are you sure it’s plastic? Without a pic it sounds like it could be a replacement glass cylinder for the heating chamber. There’s a glass cylinder behind the metal one where a stem is inserted. He’s known for throwing in extras and goodies; I got some too but can’t remember what they were, lol.
Time for me to pick a strain and check this baby out!
Vaporific
All who wander are not lost...
Enjoy! That’s one extra part I don’t have but then again I’ve thankfully never needed an extra in 23 months. Welcome to the TM club! I look forward to reviews after you decide which strain to use
Djsleepy
Well-Known Member
More TM Info:
NEW WAY to go into temp calibration mode:
When doing the 5 triple clicks make sure you wait for color sequences to stop before attempting next triple press as the button is unresponsive during flashing colors.
Temp calibration colors and how many steps forward/back
BLUE (-3), PURPLE (-2) TURQUOISE (-1) GREEN (0) ORANGE (+1), RED(+2), WHITE (+3)
oh, about the colors, the orange is a little hard to see, as the green is so overpowering in brigthness. But there is red in the mix after green, but it is probably not too clear. when you hold hand or wall etc. close to the light, you can see the separate RGB LED colors, like green and RED same time before it becomes RED.
Everything else is the same as before! Any questions just ask!
NEW WAY to go into temp calibration mode:
When doing the 5 triple clicks make sure you wait for color sequences to stop before attempting next triple press as the button is unresponsive during flashing colors.
Temp calibration colors and how many steps forward/back
BLUE (-3), PURPLE (-2) TURQUOISE (-1) GREEN (0) ORANGE (+1), RED(+2), WHITE (+3)
oh, about the colors, the orange is a little hard to see, as the green is so overpowering in brigthness. But there is red in the mix after green, but it is probably not too clear. when you hold hand or wall etc. close to the light, you can see the separate RGB LED colors, like green and RED same time before it becomes RED.
Everything else is the same as before! Any questions just ask!
Last edited:
I actually have one more question...
When will someone bite the bullet and finally create a "best of" thread for the Tinymight, before the amount of postings becomes too much for a single human life^^
Don't look at me, I have a good excuse, I'm German and reading and understanding English is much harder for me than for a native speaker
