Good luck unless things have changed significantly .... they didn’t care how much they fucked me over in the past ... it’s simple ... I can either continue to spend more and more money on shipping ($25 a shot), or I can keep my 2 lifetime warrantied paperweights ... since your only recourse is email and support tickets, and you can’t actually talk to anyone, and there is no way to escalate an issue ... you are basically 100% at their mercy to do whatever the fuck they want to you and to tell you whatever they want as they can’t be held accountable ...That's a real CS no-go! At least they should privilege your new (old) RMA! "The RMAed piece don't work? Back to start of our waitlist!" WTF? I'd try to force them to handle your RMA privileged.
Naturally replies were decently fast on this exchange until of course
I wrote my rant email. Probably some stuff I shouldn’t have wrote, but oh well... honestly I think I’m done with the hopper. Especially since they made me buy new batteries.
Now, the hunt is on. I love my Mighty but I love the instant punch the hopper gives.
LBE!! Not made yet tho
Hopper is still going strong Knock on my LB!
Could become a nice ritual - the daily GH update by @newVaper420 . But then you have to bring a bit more. Telling a joke or a wheather report at least!
Wow. And greetings. Newbie poster but long time lurker on FC and this forum - and I own a Ti Hopper. It's two years old and, believe it or not though most of you will believe it, I ordered it over 3 years ago (pre-order). It's my only dry herb vape, use it daily and, sadly, it's time it goes in for service. Yep, the backend is getting too hot and most draws are ghost pulls with little vapor produced.
Hi can I ask do you get flashing blue lights when drawing as iv noticed that when this is happening even on a fresh battery that there isn't enough power going to the heater which could explain the wispy vapor. Does the backend heat up a lot? If it is flashing you could try adjusting the tightness of the backend untill the lights are steady blue when drawing. I have found that just before full tightness is a great spot for mine. Might be worth a trySo is there any success story about self fixing low temp/light abv/light vapor production ?
Tried: compressed air, different batteries, moving temp dial to 1 and the 5 again, rubbing bit of iso on the inside of body part.
Had great vapor and dark abv for the first week or so ( received early June ) Now only using it on 5 and it feels like 3.5.
I’m still enjoying the hopper very much, gets me high and it’s my only vape but it can probably work much better.
I don’t want to send it for warranty I would rather continue using as is...
Hi can I ask do you get flashing blue lights when drawing as iv noticed that when this is happening even on a fresh battery that there isn't enough power going to the heater which could explain the wispy vapor. Does the backend heat up a lot? If it is flashing you could try adjusting the tightness of the backend untill the lights are steady blue when drawing. I have found that just before full tightness is a great spot for mine. Might be worth a try
I had some success recently fixing this issue with my SS Hopper ... finally ordered some long wooden q-tips and used one with 99% ISO (actually a couple) and scrubbed a bunch of black carbon from the contact in the base of the body. The first q-tip was black! And I’ve cleaned this recently with a regular q-tip the best I could more than once!I tried that as well. Had flashing blue lights, then adjusted backend,and lights stopped flashing. Works good but then again, no brown abv and no white thick clouds.
I think it started after the first battery charge. It kept going on blinking red, then I changed a battery and it wouldn’t charge until I found a sweet spot with the beckend.
Now it charges fine all 3 batteries. Also, front end gets really hot feels like hotter on the outside than the chamber. And abv is always dark green
I’m thinking to order a new body part but waiting to hear feedback from @mario I think we have the same issue..
I tried that as well. Had flashing blue lights, then adjusted backend,and lights stopped flashing. Works good but then again, no brown abv and no white thick clouds.
I think it started after the first battery charge. It kept going on blinking red, then I changed a battery and it wouldn’t charge until I found a sweet spot with the beckend.
Now it charges fine all 3 batteries. Also, front end gets really hot feels like hotter on the outside than the chamber. And abv is always dark green
I’m thinking to order a new body part but waiting to hear feedback from @mario I think we have the same issue..
By saying “the contact in the base of the body” you mean when you take out the battery ?I had some success recently fixing this issue with my SS Hopper ... finally ordered some long wooden q-tips and used one with 99% ISO (actually a couple) and scrubbed a bunch of black carbon from the contact in the base of the body. The first q-tip was black! And I’ve cleaned this recently with a regular q-tip the best I could more than once!
Since then it’s been working much better, Abv is better, body heat issue has gone away, and no longer goes to flashing red 80% of the way through the draw.
Yes, the one in the middle at the bottom of the body (where the positive battery post makes contact)By saying “the contact in the base of the body” you mean when you take out the battery ?
Yes, the one in the middle at the bottom of the body (where the positive battery post makes contact)
Also, clean the back end threads and the threads on the body where the backend screws on. Good luck!I think I tried that before, but I’ll give it another shot..
Fingers crossed!
We’ve talked about cleaning the threads with a tacky putty like Uholdit (I think that’s what it’s called). That stuff works better than trying to use iso on the threads.Also, clean the back end threads and the threads on the body where the backend screws on. Good luck!
You're fucked, bud.What's the over under on whether I'm ever going to get a response from Hopper? Still nothing. They did receive my two bodies, and the rest of the stuff at 11am their time (I think), this morning.
Still nada.
LOL.