StemPod by MPL

[iDRINKBLEACH]

The base is 22MM but the steel sleeve fits over it making it over 22MM by quite a bit.
Just a heads up as some mods like the pico 75 watt units won't fit unless you use two heatsinks to raise it up.
I only use wattage mode and kanthal wire.
You can use different wire and tcr\cruise mode but I haven't fucked with that too much.

Okay good to know. I'm pretty pumped to start learning it. I like on demand the wife is learning how to manage, she's got baby lungs and when it's not heat soaked she struggles a bit.

 

[arb]

Okay good to know. I'm pretty pumped to start learning it. I like on demand the wife is learning how to manage, she's got baby lungs and when it's not heat soaked she struggles a bit.

mrs.arb did good with it but sometimes I will get it going then hand it over.
Hard for any convection vape to work with a 4 second puff.

 

[iDRINKBLEACH]

mrs.arb did good with it but sometimes I will get it going then hand it over.
Hard for any convection vape to work with a 4 second puff.

We are in the same boat. I will preheat for mrs bleach right before I pass to her when i see her struggling.

 

[invertedisdead]

Hard for any convection vape to work with a 4 second puff.

LOL that’s too real @arb - And 4 seconds might be generous over here, seems more like two or three max.........

 

[Highhowareyou]

Hey FC, thanks to some advice from Goldenbud I have vaped 4 bowls today with no combustion or Hotspots, god bless you all i hope your having a good night

 

[RustyOldNail]

The Chinese have finally released a single 21700 battery DNA75C mod. It’s been a long time since the Lost Vape Mirage, which I own, but was discontinued. This one is not cheap, but if you like the chipset and 21700 battery, you have to pony up. I just ordered a red one. Or just stick with wattage.....

Element Vape - Online Vape Shop - Vape Mods, Kits & E-Liquid

Shop incredible deals at Element Vape, a progressive online retail establishment serving the vaping community with mod kits, pod systems, and premium eJuice.

www.elementvape.com

 

[Highhowareyou]

Wattage has been producing even abv for me but I find that the stempod drains my batteries quickly do you think 1 21700 is enough?

 

[RustyOldNail]

Wattage has been producing even abv for me but I find that the stempod drains my batteries quickly do you think 1 21700 is enough?

For me, at home, one 21700 is fine, I just swap. If you are a heavy, mobile user, get a 2-3 battery mod. I like single bat mods. I believe it’s approximately 20% more capacity then my 18650’s, but a true 30 amp. 4000mAh battery, Samsung 40T.

 

[Highhowareyou]

I'm more of a mobile user could you recommend a 2 battery mod? I was thinking about a drag 2 but honestly I don't know where the best place to get a mod online would be

 

[arb]

The voopoo drag is better than the drag2.
I prefer the geekvape aegis x by leaps and bounds myself.

Element Vape - Online Vape Shop - Vape Mods, Kits & E-Liquid

Shop incredible deals at Element Vape, a progressive online retail establishment serving the vaping community with mod kits, pod systems, and premium eJuice.

www.elementvape.com

 

[Highhowareyou]

Help my stempod is not producing clouds.
The resistance reads at .22 and the coils do not appear damaged. I am holding down fore on 45 watts for 5 seconds then doing a 10 second inhale but no vapor help! When I attach the base to my mod it reads atomizer low

 

[arb]

Take off the cover and check to see if the screws holding the coils are tight.
Almost guarantee that is your issue if not holler and I will try and get you going.
Do they glow equally?

 

[Highhowareyou]

Top screw was loose, I tightened it and it now reads .20 God bless

 

[arb]

Top screw was loose, I tightened it and it now reads .20 God bless

Does it work ok?

 

[Highhowareyou]

It worked fine for one bowl, then the resistance jumped up again after I charged my mod

 

[arb]

That seems to change some from mod to mod.
As long as both coils glow evenly it is working correctly.

 

[Highhowareyou]

Hey Arb today my stempod started to go up in resistance during my session first hit was .21 second hit it was up to .32 then it said atomizer not found how do I fix this?

 

[arb]

Did you check your screws and is it glowing evenly @Highhowareyou ?

 

[Highhowareyou]

The screws are tight but the coils glow from the middle outwards

 

[arb]

Making sure they aren't hot give the coils a wiggle and see if they move.
Do you have more coils and feel comfortable changing them @Highhowareyou ?

 

[Highhowareyou]

I have wire cutters and two spare kanthai coils but I haven't changed a coil before any tips? Also the coils don't wiggle much when i touch them

 

[arb]

There are several videos on YouTube including one from modpod about changing coils,just make sure your positive post is tight.

 

[Highhowareyou]

How do I tighten the positive post?

 

[arb]

How do I tighten the positive post?

The brass screw in the base of the 510 thread.Don't crack the ceramic insulator by over tightening.

 

[Highhowareyou]

After installing new coils I found that my issues persisted until I switched to my eleaf rim C i still need to tighten the screwws occasionally but the problem of resistance jumping between hits is solved