Thanks for doing this! The middle ABV looks perfect on paper.
Based off color and past experiences I'd say that something might be left if you where you too use to edibles but that might not be right. The cool down click does come after the end of the draw for sure. Using the magnetic stand to remove the while it's hot makes the cool down noticeably quicker.
The tool also functions as a Magnetic stand which is included in the pre-order kit. You can also stand the entire Anvil on it, the herb chamber must be installed in the Anvil as it contains the magnet that snaps onto the magnetic stand.
A good rule of thumb is the Helix steps up the intensity a notch and digs deeper than the Terp Chamber for any equivalent amount of heat and time. @PaperClouds posted an excellent photo of the ABV shades at different heating points on the Anvil's oven. All were done with the half size Terp Chamber with ~ 0.1g https://fuckcombustion.com/threads/anvil-by-vestratto.51804/post-1608264
We might be able to show some photos of it. This wasn't a concept, it was over a year of hard work by many people and was fully functioning, 95% ready for retail sale. The gaining popularity of portables and falling demand for desktop vapes 3 years ago had us take technology from that and apply it to a portable - the Anvil. We might still build the monster in the future, so don't want to share too much info about it until it's IP is protected.
Great question @JEMSKU We also read those Google "facts" about neodymium magnets and the reason why neodymium magnets are used with the Anvil is because we never really noticed any magnetic degradation. Truth be told, we never used any single part for more than 2 weeks at the beginning before we made a new improved one, but later versions had years worth of heat cycles put through it.
Will there be some type of metal holder that all our extra bowls can screw into for storage and discreet travel when full?A good rule of thumb is the Helix steps up the intensity a notch and digs deeper than the Terp Chamber for any equivalent amount of heat and time. @PaperClouds posted an excellent photo of the ABV shades at different heating points on the Anvil's oven. All were done with the half size Terp Chamber with ~ 0.1g https://fuckcombustion.com/threads/anvil-by-vestratto.51804/post-1608264
The Helix ABV would be darker with everything else being the same. Keep in mind the Terp Chamber (named by our testers) was given that name for a reason, your vapor tastes like it smells - terp tingles. The Helix gives up some flavor to reach down deep and grab all the actives available in any particular strain. Different vape signatures from one device just from changing chambers.
We might be able to show some photos of it. This wasn't a concept, it was over a year of hard work by many people and was fully functioning, 95% ready for retail sale. The gaining popularity of portables and falling demand for desktop vapes 3 years ago had us take technology from that and apply it to a portable - the Anvil. We might still build the monster in the future, so don't want to share too much info about it until it's IP is protected.
Great question @JEMSKU We also read those Google "facts" about neodymium magnets and the reason why neodymium magnets are on the Anvil is because we never really noticed any magnetic degradation. Truth be told, we never used any single part for more than 2 weeks at the beginning before we made a new improved one.
Even still we took steps to mitigate neodymium fatigue due to long term heat exposure. If you look at the Anvil Chamber Cut-Away, you'll notice the magnet is as far away from the heat source as possible, has a cooling air hole and has minimal contact area with the heat zone, all thoughtfully done to avoid magnet issues.
this one definitely has my attention!!!! can't afford to jump on the pre order, just to much I have to spend for xmas
looking forward to seeing some of these in the wild!!!!
For sure. It's on our roadmap as a future product. Nothing is in stone yet, so any design ideas are welcome.
We hope to have some extra herb chambers available, but not sure which ones will be ready on time yet.
I imagine just a bar with 5 or 6 threaded holes where the bowls would screw into. I'd say a circle but I think a rounded bar would be better in the pocket.For sure. It's on our roadmap as a future product. Nothing is in stone yet, so any design ideas are welcome.
We hope to have some extra herb chambers available, but not sure which ones will be ready on time yet.
something like this maybe
Yes, that's what we had in mind too
Since the Anvil chamber threads are on the bottom, a revolver design could work, but I wouldn't want that big bulky thing in my pocket all daysomething like this maybe
i imagine once this thing hits the marker acessories will not be a problem. People within FC and the company itself will come up with the goodies!!Buy Gold Multi Cartridge Revolver Vape Stand Online in India - Etsy
Buy Gold Multi Cartridge Revolver Vape Stand online on Etsy India. Shop for handmade, vintage and unique Gadgets items from HorizonVH online on Etsywww.etsy.com
Any chance of single screw on caps for people with only one or two extra bowls?Yes, that's what we had in mind too
This is exactly what I want this device for...portable outside carry for disc golf. Not a fan of the Paul McBeth Nova myself, but good color choice to show AVB.Anyone else that lives in a place that gets cold and vapes outside knows it's not always as easy to achieve the same results given the surrounding air temp. I was curious as to how the Anvil would hold up in colder weather. The air temp was 38F in the video below using the half straight walled bowl . There's also a preview of part of the functionality of the case, I'm not going to show the whole thing since that isn't it's film form.
And of course the resulting ABV
View attachment 14397
Anything is possible, just we are under time pressure to launch the pre-orders so those kinds of things are all future considerations.
We can't promise a day, but will for sure send notifications at least 2 hours before the drop. If you miss the pre-order, we will have more soon. Remember, everything Anvil related is made right here from local raw materials, no waiting for months like imported products.
@JEMSKU Wanted to update our previous response to this question. The magnet is actually only in the stand, not in the herb chambers.
This vaporizer really kinda looks like a supreme substitute. It's really really impressive
