kilo
Well-Known Member
Thanks, I'll look into it. It's 14mm though, so I might need to buy a new j-hook. I'm going to check out Cannabis Hardware as well.
TinyMight / TM 2
- Thread starter kuzko
- Start date
After a soapy hot water wash, I gave all appropriate parts an iso soak & then wiped them over with tissue & cotton buds. At one point, I noticed there was a small amount of grey residue on the tissue although I'm not entirely sure which part it came from. Also, when I was finished I could see the used cotton buds were faintly tinged grey when compared to an unused bud, but I was looking very closely. I also feel there was a slight smell with the initial burn-off, which has now mostly dissipated & I could see nothing visible burning-off when it was viewed under a lamp. Overall, I am happy with the out-of-the-box condition, but I will always carry out my own cleaning routine before using a vape - if nothing else, I find it's a good way to get to know all the parts, how it goes together and maybe gain a better understanding of how it works before I use it.
FWIW mine came with the larger o-ring on the top section of the cu, & the smaller o-ring on the bottom section.
And finally, a little bit of sunshine to help highlight that lovely grain:
Last edited:
Sidvicius
....
I'm going to talk and share with you (I don't think I need to talk about it with my wife 
) unfortunately mine smelled a lot of the electronic board even the metallic heating system, nothing serious I'm used to both with the vaporizers bought in the past and because I it often happens to buy atom RTA for ecigs dirty with processing oils etc ... I still recommend cleaning the stems and the cooling system, with a few cycles in the ultrasonic washing machine with 96% food alcohol I am more calm (food because I had that , I clean the Ecg that I told you above and I do extractions for the aromas and I prefer it to iso because food alcohol, even if evaporating it changes very little) then I did two laps, one per stem with a really poor light herb, pulling without breathing at various steps up to 10, then I wanted to try it to see if the smell had gone away but I finished battery .... cmq heat to 10 the metal parts are difficult to touch (but it is a common thing at those temperatures even on other vaporizers).
) unfortunately mine smelled a lot of the electronic board even the metallic heating system, nothing serious I'm used to both with the vaporizers bought in the past and because I it often happens to buy atom RTA for ecigs dirty with processing oils etc ... I still recommend cleaning the stems and the cooling system, with a few cycles in the ultrasonic washing machine with 96% food alcohol I am more calm (food because I had that , I clean the Ecg that I told you above and I do extractions for the aromas and I prefer it to iso because food alcohol, even if evaporating it changes very little) then I did two laps, one per stem with a really poor light herb, pulling without breathing at various steps up to 10, then I wanted to try it to see if the smell had gone away but I finished battery .... cmq heat to 10 the metal parts are difficult to touch (but it is a common thing at those temperatures even on other vaporizers).
FelixVonTrapp
Well-Known Member
+1 …I was so excited I jumped right in.
Let's get a double burial to save money.
kilo
Well-Known Member
Make that a triple!
focalforlife
Well-Known Member
Same experience.
ArtVandalay422
Well-Known Member
Was ready and logged in at vgoodiez at 12pm est. Added TM2 to cart and immediately tried to check out, but it said sold out already. Probably within 5 seconds of total time.
Uggh. Same here. Sucks.
neoncheesecake
Well-Known Member
wow the Vgoodiez stock selling out in <1 minute tells me I should wait for the excitement to settle and then purchase my unit. my TM1 is doing great and still hits fantastically every day. I told myself and my gf "not going to get the TM2 until next year" but damn...seeing the beauty of it and all these great testimonials, may have to make it a christmas present!
Shrike
Flower Potted, Maxed, & Rio'd.
Sold out atm...so is Vapefiend.
Photonic
Lesser-Known Lurker
Less than 5 seconds based on my experience
DaVapeGuy
Well-Known Member
TM direct let's you preorder, the other vendors don't.
WisePenny
unknown. unmember.
With a current anticipated ship date of Sept 28th
EarthworldTim
Well-Known Member
Has anyone emptied out the washers and nuts from the cooling unit and replaced them with rubies? I can get some 4mm pearls in there but it's a snug fit when I put it back together. Not sure how much expansion I'd be dealing with, probably not much?
Clapped_r6
Well-Known Member
Same thing. 1 in my cart, go to pay and whoopsies its out of stock. 10 sec max
Md_Hybrid
Stuck under a 🪵
My order just arrived!
I have to run out for a bit so this is it for now but many thanks to @VapeFiend.com!
I have to run out for a bit so this is it for now but many thanks to @VapeFiend.com!
fangorn
Well-Known Member
Ahahah !
No one escapes the VAS... No one...
I'm teasing huh... I myself ordered a TM2... which will arrive when Chronopst agrees to send "electronic cigarettes"... and they respond to the complaint from my shop...
kilo
Well-Known Member
I don't think you'd have a problem with pearls and rubies as I don't think they expand that much. I'm using titanium balls and what I've done is take the bolt out of the unit, slide one up toward the mouthpiece end, pour the balls in, then put the second one in. The only hassle is that the loose balls can spill when taking it apart for cleaning so it's best done over a bowl or a towel.
Vaporific
All who wander are not lost...
Blue? Don’t you mean… RED?
Yours came with candy? I’m getting mine from VapeFiend too then (see above for color choice).My order just arrived!
I have to run out for a bit so this is it for now but many thanks to @VapeFiend.com!
My OG TM is now vacationing in Ohio which is the opposite direction from Finland from me (MA) for its repair stint. Funny how shipping and DHL works.