TUBO evic/dual

Abysmal Vapor

Abysmal Vapor

Supersniffer 2000 - robot fart detection device
rozroz said:
ok. yes it was stealth.
now i did my first on demand few hits at 350F.
seems i'm getting the hang.
if my "goal" is having 4-5 easy hits in around 3-4 minutes,
what would be the best setup regarding saving battery?
on demand or session/cruise? also considering Eco?
i think the on demand is better cause i don't use the battery as much it seems.
but not sure.
tnx for all your help.
btw this is a great device. finally i feel in the big league :D
never felt such an airflow before.
Click to expand...
Well i dont think on demand is better,because it demands more extreme wattage values than cruise,which is easier on the battery IMO,because of the heatsoaking. At some point after beiing some time in cruise mode, there is no difference between it and on demand ,but from cold start,cruise is better option for me. . Also holding the button vs just clicking it twice at least for me is more carefree experience ;) .
I already proposed this,i will repeat myself.
Turn on cruise cycle to 250 C and after 15-20 seconds cycle back to the desired temp,take a hit and if you like you can go on demand for the next one.
FJ once said. HOT TUBO = Good TUBO !
 
L

luke00978

Well-Known Member
ok so i figured out my rx200s was broken as it was only discharging 2 of the 3 cells and this must have been some to some board problem causing the overheat. have just received a brand new rx300 and it works but every now and again will say atomizer low/short and have to have the batteries pulled or the x removed and refitted . tried cleaning 510 with iso, still does it. could it be a problem in the settings?
 
Abysmal Vapor

Abysmal Vapor

Supersniffer 2000 - robot fart detection device
luke00978 said:
ok so i figured out my rx200s was broken as it was only discharging 2 of the 3 cells and this must have been some to some board problem causing the overheat. have just received a brand new rx300 and it works but every now and again will say atomizer low/short and have to have the batteries pulled or the x removed and refitted . tried cleaning 510 with iso, still does it. could it be a problem in the settings?
Click to expand...
I had the discharging issue with my RX300 it was draining one cell more than others.,it was software related but i found a fix on github and FJ implemented it in the current software.Also make sure you select the battery MODEL from the expert menu. Are all of your batteries same brand ?
 
J

jay87

Well-Known Member
rozroz said:
What is your ideal temps jumps low to high in F?
Click to expand...

For me I like 340F to get out the flavor and then 390F for a couple draws to finish.

I'm still experimenting though.

I recently used a ~1/2 packed stem at 400-410F and got crazy clouds for 1-2 draws.

I'm still cautious about high temps as the Tubo can get very hot and there's a lot of room for experimentation with draw speed and temps :science:
 
rozroz

rozroz

Well-Known Member
SirCrackKillaH said:
Tubo! I'm excited about this. I started looking at pictures online. Buy direct from the manufacturer is the best bet right? I gotta look through all these posts. Cool stuff man :D
Click to expand...

i just got it (bought it from the maker here) and it's a really serious device.
premium feel, excellent built. i come frrm lower level products and this is another level for me.
 
Last edited:
S

shaolinmilk

Well-Known Member
I can't state this enough... use a longer stem and your experience with the Tubo will drastically improve. With that said, I feel like the Tubo is #1 on my list now for portable solo sessions where my Mighty is my go-to for multiple people. The Tubo man... such a straight forward design and it delivers like no other. Really really great vape.
 
funkyjunky

funkyjunky

www.lamart.ch
Manufacturer
heeeelllooooo!

the store is ready and online! check this out! :D:party::cheers::nod:
thanks for all the support, could not have managed without it!

4P2QdnF.png

www.lamart.ch
​
price increase:
TUBO evic - $190
TUBOx- $125


includes a 2 year warranty on everything except the box mod and glass.
the box mods are covered by joyetech for 90 days (i think they usually last once they have survived this period). in the rare case that it should die along the journey, replacement/repair costs for an evic vtwo mini for example are around $35 plus shipping to me.



Abysmal Vapor said:
Turn on cruise cycle to 250 C and after 15-20 seconds cycle back to the desired temp,take a hit and if you like you can go on demand for the next one.
Click to expand...
this is exactly what the warmup mode does with less button clicking. you can assign it in the 'menu>interface>clicks'. except it stops at a threshold wattage (heater hot=less watts to keep it hot) and not time.


have a very nice weekend everyone!
 
Abysmal Vapor

Abysmal Vapor

Supersniffer 2000 - robot fart detection device
luke00978 said:
very swish looking shop, managed to get the x working for the minute so heres a bit of free advertising...

1st draw a primer, 2nd drawing as hard as i can
Click to expand...
Haha i would colapse if load that much.Dude smth is wrong with your batteries :) .
I am using this version of the software ,i am sure it has the fix for even battery drain and charge. Also make sure allyour batteries are same brand and charged to same voltage before use and the you ave dialed in the battery brand from the expert menu
http://tubo.lamart.ch/fw/170926-tubomyevic-tempcruise-fireactive-ecobar-noclicksreset-beta.bin
 
Last edited:
Abysmal Vapor

Abysmal Vapor

Supersniffer 2000 - robot fart detection device
luke00978 said:
i know they say balance, they’re brand new vct4 charged twice in a 4 bay, you think i should contact the seller? theyre off ebay but said genuine and had good fedback
Click to expand...
Enter Expert menu see BVO field and if all battery Voltage values match .When you charge them fully in the charger check again.
Also make sure you select battery type to VTC4. (Above BVO is BAT)
You have problems either with the batteries or uneven battery drain. You can try the software version i posted above i am using it without issues.
 
L

luke00978

Well-Known Member
Abysmal Vapor said:
Enter Expert menu see BVO field and if all battery Voltage values match .When you charge them fully in the charger check again.
Also make sure you select battery type to VTC4. (Above BVO is BAT)
You have problems either with the batteries or uneven battery drain. You can try the software version i posted above i am using it without issues.
Click to expand...

ok ive put that firmware on (think i had it on anyway) and ive got the batteries back in the charger, i checked the bvo before and they weren’t even, ill check when charged and see if they need returning or not, cheers!
 
Shit Snacks

Shit Snacks

Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
funkyjunky said:
heeeelllooooo!

the store is ready and online! check this out! :D:party::cheers::nod:
thanks for all the support, could not have managed without it!

price increase:
TUBO evic - $190
TUBOx- $125


includes a 2 year warranty on everything except the box mod and glass.
the box mods are covered by joyetech for 90 days (i think they usually last once they have survived this period). in the rare case that it should die along the journey, replacement/repair costs for an evic vtwo mini for example are around $35 plus shipping to me.




this is exactly what the warmup mode does with less button clicking. you can assign it in the 'menu>interface>clicks'. except it stops at a threshold wattage (heater hot=less watts to keep it hot) and not time.


have a very nice weekend everyone!
Click to expand...

YES THAT LOGO IS AMAZING!!!
Congrats on reaching this landmark @funkyjunky, now my friends here can buy one more easily :tup:
 
S

sickmanfraud

Well-Known Member
I remember that there were a few questions from North American FC members about getting bent stems in the USA.

I have used a stem like this https://www.amazon.com/gp/product/B01M4FDUQU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 which is $7.95 with free shipping (min order on Amazon applies). The stem is very close to the bent stem that we purchased with our Tubo's. This includes a screen.

Here is a link to screens that fit this stem: https://www.amazon.com/gp/product/B073WQJYRS/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

I have tried one of the screens and they fit fine.

BTW, I know it is a piece from an Arizer Q all glass balloon kit.
 
Last edited:
rozroz

rozroz

Well-Known Member
sickmanfraud said:
I remember that there were a few questions from North American FC members about getting bent stems in the USA.

I have used a stem like this https://www.amazon.com/gp/product/B01M4FDUQU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 which is $7.95 with free shipping (min order on Amazon applies). The stem is very close to the bent stem that we purchased with our Tubo's. This includes a screen.

Here is a link to screens that fit this stem: https://www.amazon.com/gp/product/B073WQJYRS/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

I have tried one of the screens and they fit fine.
Click to expand...

so how do you get one to Israel?
 
S

sickmanfraud

Well-Known Member
rozroz said:
Yea that will happen.. tnx anyway.
Click to expand...

FYI, I have been using the Extreme Q balloon stem for a few weeks. I was hesitant to suggest the Amazon stem until it arrived and I was sure it fit okay. That was last night.

Once I satisfied myself it was fine to use I recommended it.

Saturday night 20 something hours until my wife's flight and my @DDave vapor cooler broke. Everything was fine until it was no longer possible to send a replacement to her.
 
You must log in or register to reply here.
Top Bottom