Discontinued The Persei Vaporizer for herbs and concentrates.

[Authentic]

Hearing that the digital LCD top is coming soon really got me hard.
I just ordered a chrome Persei.

How low will the digital top go? Can we do less than 3.7v?

 

[THC SCIENTIFIC]

Hearing that the digital LCD top is coming soon really got me hard.
I just ordered a chrome Persei.

How low will the digital top go? Can we do less than 3.7v?

range will be 4.0v - 7.4v The digital top can only be used with the 2x 18350 batteries.

 

[ru_frothi]

The Taste issue we are tracing back to high voltage, At this voltage the heating wire oxidizes really quick, and sets into the silica rope. As apposed to the 3.7v which takes a while.

Looks like it was not a single issue but two different issues.

The first issue was machine oil taste, and we did have a few cartridge shells that did not get washed, but the second issue we are having looks like its on high voltage device only. IE 4.0 ohms and 5.0 ohms.

Many people without knowing are complaining of bad machine oil taste that is not, it is just the heating wire oxidizing and setting into the silica rope.

We are working to remedy this by actually pre using the heating wires so they are fully oxidized before we manufacture them so the taste is gone before they hit the consumers hands.


So a recap of that is going on.

Few people complained of bad tasting cartridges on the omicrons. Yes we did have a bad batch. All is gone and new items are washed twice, and put into a autoclave twice before being transported into a clean room for assembly.

Second issue that was mistaken to be part of the first issue of bad taste, is attributed to oxidation. this is only happening on the high voltage model that is noticeable in large quantity, this also happens in low voltage models, but it takes longer time for it to happen and it is so small that it is barley noticed in the taste, The heating wire is oxidizing and setting into the silica rope. Nothing to be worried about. Taste goes away after a few hits. You can dry run it but be careful to allow cool down periods in between dry hits.

This update we have, we are working on a upgraded cartridge, but this will happen after the herb chamber, nail cart, and herb cartridge ( my kryptonite )

The tank top does vent, but check this issue out, because the cartridges are hand assembled we have not been able to control the tolerance on the position of the top bridge. Given that it can be off by a millimeter or two, that can cause the mouth piece to make a direct seal, this seal now creates suction at the tank side when people inhale, this is why we said take the rubber white round cap off during use.

Now we have made some changes to the future mouth pieces we have coming to accommodate this tolerance and also made a tool that will keep the top bridge positioned at the same length during assembly. The tool will allow current consumers who have older mouth pieces to work properly, and the new mouth pieces we have coming will make sure just in case by act of god, one cartridge bridge is not in the position it is supposed to be will still work because it has a back up feature to prevent negative pressure in the tank.



Hope this explains it all.

Thanks G for explaining it all.

Unlike Vitolo my double top is quite tight and I feared breaking it trying to squeeze the two silicon tips on there. I will try this again.

 

[Authentic]

Is it okay to keep the double top on when only using one cart or do you advise switching it? Are there any downsides to hitting one cart with the double top?

 

[Darb]

Is it okay to keep the double top on when only using one cart or do you advise switching it? Are there any downsides to hitting one cart with the double top?

I believe THC has already said this would be ok. I've done it with no problems.

 

[Authentic]

Thanks brah!

 

[Vitolo]

I can see where the digital top will eliminate guesswork.
After the double carts.. and 5 ohm at 7 V, I got more courageous (I did get the extra batteries!!)
I now am doing this with the 4 Ohm cart at a full 7.4 V.
Liking the thickness of the vapor... next stop 3 Ohms...

 

[Stu]

As always, love your vids, Vito!

I can't wait to see your 3 Ohm face.

 

[DubCRider]

If there was such thing as Vorn(vaporist porn) then Vitolo would have the best "Ohm Face" in the industry!

Careful with the 3ohm cart with fully charged 7.4v setup. A friend of mine killed two 3ohms within 10 hits each.

 

[Darb]

I'm liking the 2.4ohm Omicron carts at 6.0 or 7.4 volts. Obviously just short three second hits. I have filled two three and two four ohm carts and with my shitty luck all four taste bad!! The Omicron carts still taste great though, even after numerous grams of concentrate.

 

[THC SCIENTIFIC]

ya 3 ohms dont last that long, I seriously think vito will be exception to the rule and the first to reach 100 hits on 3 ohms 7.4v setup.

 

[THC SCIENTIFIC]

update guys, The Hammer will be packaged with the click on/click off top, the Top and heating rod will have a 6 months warranty on manufacturers defects.


Price $59

Will be available soon.

 

[OF]

If there was such thing as Vorn(vaporist porn) then Vitolo would have the best "Ohm Face" in the industry!

Seems to me "Ohm Face" and "Poker Face" are at opposite ends of the Face spectrum?

Somehow, I think Vitolo might be master of both.....go figure.

OF

 

[THC SCIENTIFIC]

Seems to me "Ohm Face" and "Poker Face" are at opposite ends of the Face spectrum?

Somehow, I think Vitolo might be master of both.....go figure.

OF

doesnt hurt to be Italian either when it comes to porn and poker, and some how faces. I dont know what im talking im gonna go destroy a new toy i have.

 

[The_Reckoning]

Ok bad battery. Submit a ticket and we will take care of it.

Thank you for helping me figure out my battery issue. I received the new batteries in today, and finally got to take this thing for a spin.

It is a monster.

Good work all, thanks again for the innovation, as well as the customer service. I'll gladly recommend you or your products to anyone. Although, after a rip from a Persei or an Omicron, they usually don't need much convincing.

Also, Thanks for the tip to whomever mentioned to prime the higher Ohm carts on 3.7v. Should save us all a few carts.

 

[OF]

doesnt hurt to be Italian either when it comes to porn and poker, and some how faces. I dont know what im talking im gonna go destroy a new toy i have.

Now that you mention it, ever notice there are times in his videos where you can't see what he's doing with his other hand?

No wonder he moved and changed his name.

OF

 

[THC SCIENTIFIC]

Thanks G for explaining it all.

Unlike Vitolo my double top is quite tight and I feared breaking it trying to squeeze the two silicon tips on there. I will try this again.

No problem Ruf, hold off on the trying if it is two tight, we have other mouth pieces we can have you try, they are not all here but we have a few we can send you to try. Submit ticket and ask for me in it.

 

[THC SCIENTIFIC]

Now that you mention it, ever notice there are times in his videos where you can't see what he's doing with his other hand?

No wonder he moved and changed his name.

OF

Witnesses do not live long, that is what i learned when i was young, so i dont want to know.

 

[OF]

Witnesses do not live long, that is what i learned when i was young, so i dont want to know.

Good point.

Vitolo who?

OF

 

[THC SCIENTIFIC]

Good point.

Vitolo who?

OF

Im sorry i dont speak english.

 

[OF]

Im sorry i dont speak english.

You lie and I'll swear to it....


OF

 

[druminfected]

I can see where the digital top will eliminate guesswork.
After the double carts.. and 5 ohm at 7 V, I got more courageous (I did get the extra batteries!!)
I now am doing this with the 4 Ohm cart at a full 7.4 V.
Liking the thickness of the vapor... next stop 3 Ohms...

awesome video Vito, I love all of your videos and wish you made one everyday! Correct me if i'm wrong though, but it's not advised to use the 4 ohm carts with the 18350 batteries since they are really 8.4v so watch out vito.

 

[Vitolo]

I'm watchin'.... I'm watchin'....

 

[OF]

I'm watchin'.... I'm watchin'....

Hey, and we're all watchin' you. Well not all, but the smart ones are.

Is it any wonder so many kids want to be just like you when they grow up? Or that so many mothers would share that very wish for their little bundles of joy?

Forget the Academy snubbing you again this year, they're just jealous and we all know it. Well, OK, some of them feel threatened with your success, but they're jealous too. Keep making those wonderful videos, spit in the face of 'the Hollywood system'.

Have you considered dual language versions? Perhaps just sub titles for now?

OF

 

[Vitolo]