TETRAx
- Thread starter funkyjunky
- Start date
Jacer
Well-Known Member
I have it running aroud .15 higher than it "should be' (i.e. what is on the tag). I'm running it around .260 right now on a RX Gen 3 dual. Also thanks for the heads up on the signature!
Thank you friend I appreciate it! The only thing that beats the TETRAx in my entire line up is my Flowerpot haha, and even then it can be close sometimes.
I can not for the life of me to get tuboevic to recognize my rx gen 3. I just bought it, downloaded tuboevic, run it, and it says unknown device? Am I missing a step or do I have to do something to the rx before running updater?
1nd3cEnt
Well-Known Member
Download the original firmware of the rx gen3, reflash the device with that fw, & then try flashing tuboevic fw again. Or else, download Artic Fox, flash it, then try flashing the tuboevic fw again.
Sometimes compatible mods would not recognize nor flash the tuboevic fw, so it was necessary to flash, say, Artic Fox fw first, then flash the tuboevic fw on top of it. Strange but true.
Ha I was just editing I did manual with toolbox. Thank you! Just realized I ordered wrong mod. Ugh hectic ordering around holidays caught me up. So the p80 with the x has no overheating issue?
Last edited:
recent tetrax batch:
Eclipse
Well-Known Member
So I managed to snag this prebuilt Zircote Tetra X.
Anyone have any recommendations on a 2 battery 18650 mod that would work well to strap on to a small bubbler? Looking to make a self contained couch setup. I would take recommendations on a bubbler as well. Thanks!
Anyone have any recommendations on a 2 battery 18650 mod that would work well to strap on to a small bubbler? Looking to make a self contained couch setup. I would take recommendations on a bubbler as well. Thanks!
bkkbob
Obsessive Collector
The Wismec Reuleaux RX GEN3 Dual works pretty well.So I managed to snag this prebuilt Zircote Tetra X.
Anyone have any recommendations on a 2 battery 18650 mod that would work well to strap on to a small bubbler? Looking to make a self contained couch setup. I would take recommendations on a bubbler as well. Thanks!
MikeRotchHertz
Well-Known Member
That's your best best or the evic dual if you can find it. I'd stay away from the cuboid 300. All mine started overheating eventually. P80 is of course a great single cell option
Eclipse
Well-Known Member
As far as I can tell the p80 is discontinued and out of stock everywhere I have looked.
GoldenBud
Well-Known Member
if you're from USA visit here:
Search: 0 results found for "Wismec P80"
VGoodiez is a small family owned business and home of the heavies. We also specialize on hand crafted artisan vaporizers and accessories from around the world. Getting the Good stuff was never so EZ! Thanks for supporting small business!
Wismec Reuleaux RXmini 80W 2100mAh TC VW APV Mod Kit - authentic / 2ml / 0.2ohm / 1-80W / 100-315'C(200-600'F) at FastTech - Free Shipping
Probably the best deal for a Wismec Reuleaux RXmini 80W 2100mAh TC VW APV Mod Kit authentic / 2ml / 0.2ohm / 1-80W / 100-315'C(200-600'F) USD as of 7/27/2022 - Free shipping worldwide on all orders. Prices unbelievably cheap.
Last edited:
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Even though the P80 is a great mod, if you are using a TetraX, I do think there's a lot of value in getting a dual battery mod... G3D should be fine though it can have issues, like you should get an external charger too...
BubbleDrop
Well-Known Member
The P80 is not listed on the TETRAx web page. Is it still fine to use it ?
TUBO evic base kit
www.shop.lamart.ch
Also, do you know if the Wismec Sinuous Ravage 230 with Red Panda would work ?
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
The P80 is not listed on the TETRAx web page. Is it still fine to use it ?
TUBO evic base kit
Also, do you know if the Wismec Sinuous Ravage 230 with Red Panda would work ?
Yes P80 is fine and simple because the settings will match the Tetra P80, but no to those ravage mods, I mean you can use red panda with a tetra, and try to use the settings and make them match, but it would be much better to use tubo firmware in order to experience the proper regulation and all the other features available... like that is how you will get the most out of the heater!
GoldenBud
Well-Known Member
works. TCR 185 , resistance - as the sticker says for starters. Temp dominant ... i like to config these settings from the PC , not from my mod tho
but it's always better to use the tubofirmware because the warmup to cruise is very nice option for the TETRAx
BubbleDrop
Well-Known Member
Thanks ! For test purposes, I'll try to get a P80 mod and see what I can do.
Well noted, thanks a lot !
I already use this mod for both the Splinter and the Splinter Z, with @bossman settings. :-)
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Yeah you'll notice comparatively that it will eat through batteries more, so you may need to swap more, but it is a little easier to recharge externally and have plenty waiting. Molicell P26A are a great cell for this btw!
BubbleDrop
Well-Known Member
Oh I was actually going to get those ! Thanks for the hint.
toketogether
Founder of Puff
I purchased a TetraX second hand and am having the same issue with finding the right resistance.
Should the coils ever glow orange?
When I drop the resistance low, the temp display can go crazy high while the coils stay cool. If I go too high on resistance, the display will show a low temperature but the coils glow orange. I bought it from a person that used it at 0.262 but I had a hard time getting it to produce vapor. I've been testing different resistances but then I realized, I don't know what the "correct" answer is and I don't want to break it somehow.
Thanks!
Should the coils ever glow orange?
When I drop the resistance low, the temp display can go crazy high while the coils stay cool. If I go too high on resistance, the display will show a low temperature but the coils glow orange. I bought it from a person that used it at 0.262 but I had a hard time getting it to produce vapor. I've been testing different resistances but then I realized, I don't know what the "correct" answer is and I don't want to break it somehow.
Thanks!
GoldenBud
Well-Known Member
no they should glow only at 260c. which mod he had? which one u got? TCR 185 right? here's how to configure :
set ur resistance. go to temp 260. click fire and hold. look at the coils. do they glow abit? if too much glowing get it down abit. if they don't glow at all raise the resistance up until they glow abit
toketogether
Founder of Puff
toketogether
Founder of Puff
Update for any that are curious
I couldn't dial it in consistently and chalked it up to my own ignorance on mods. I sold it on reddit and the purchaser replied back that the mod was malfunctioning, so, I missed out on my tetrax and the firewood I traded it for
Oh well, maybe just order a custom p80.
I couldn't dial it in consistently and chalked it up to my own ignorance on mods. I sold it on reddit and the purchaser replied back that the mod was malfunctioning, so, I missed out on my tetrax and the firewood I traded it for
Oh well, maybe just order a custom p80.
CanikUser19
Trenchtown Rock
My TetraX delivered yesterday. As suggested here, I got a P80 to run it on. Downloaded the firmware, but the updater is not recognizing the mod and does not make the update button available (stays grayed out). Did a cable check by opening up the NFE Tools updater for RP/AF and the mod is recognized there. Haven’t had any issues installing RP/AF on multiple mods recently. What am I doing wrong with this firmware?