snackmaster
Well-Known Member
When they showed it on the stream they had a screen in the vrod head top to keep them containedSo if you tip the head over can the balls still fall out the top intake hole?
When they showed it on the stream they had a screen in the vrod head top to keep them containedSo if you tip the head over can the balls still fall out the top intake hole?
I think 4mm would work better based on my experience trying to use 3mm rubies in the vrod head, but that’s just speculation.Edit: If I was to order this thing would it make more sense to order VGoodiezs 3mm ruby balls instead of quartz from CH? Rubies are better for this type of stuff…right?
Edit 2: This thing will go on a WeedEater top too…right? I’m pretty sure I’ve got my bottoms swapped at the moment.
It would not make a difference.Does anyone know if it makes a difference if you exhale through your nose or mouth? Does one get you higher than the other?
Exhaling through my nose always made me more susceptible to sinus-related problems like sinus infections.Does anyone know if it makes a difference if you exhale through your nose or mouth? Does one get you higher than the other?
I can't vouch for this specific seller:Anyone know a good place to get 4mm sic pearls?
I can't vouch for this specific seller:
out of stock now but I got these a while ago from prime and they are legit and work great...:Amazon.com: 4mm OD SIC Beads Balls Insert (20 Pack Black) : Industrial & Scientific
Buy 4mm OD SIC Beads Balls Insert (20 Pack Black): Insert Bearings - Amazon.com ✓ FREE DELIVERY possible on eligible purchaseswww.amazon.com
I can torch em white hot and drop straight into cold ISO no problem...Amazon.com: BERACKY 6mm OD SIC Beads Balls Insert (5 Pack, Black) : Arts, Crafts & Sewing
Shop BERACKY at the Amazon Arts, Crafts & Sewing store. Free Shipping on eligible items. Save on everyday low prices.www.amazon.com
I’ve been thinking about these 4mm Ti balls on Etsy. The artist will even anodize them for you. Anodized they’re about a buck a piece and sold in sets of 10.
https://www.etsy.com/listing/501428...-10-packs-plain?ref=cart&variation0=545749286
I did grab some of the quartz balls from CH, this being my first ball vape, but am I reading correctly Ti has better heat retention than quartz? I don’t have an issue with the flowerpots Ti component flavoring my vapor in any way like some users experience. I have seen that Dave sells 3mm Ti balls for the Terp Torch I believe but worry 3mm maybe to small?Does anyone have experience using Ti in ball vapes?
3mm might actually be fine. My issue with 3mm in the vrod head was they tended to settle in the diffuser holes and cut airflow. Tried to remedy that with a screen on top of the diffuser, but then I couldn't close the head all the way. I'm pretty sure the baller diffuser has the same hole pattern at the bottom, but now there's plenty of room to add a screen.I have seen that Dave sells 3mm Ti balls for the Terp Torch I believe but worry 3mm maybe to small?Does anyone have experience using Ti in ball vapes?
I saw someone mention earlier than the smaller and centrally configured airflow is causing the herb to be blown around in the bowl. Are you seeing that at all? Maybe the needing stirring is a result of this.Here is a pic of the Baller Heads 18 heat dispersion holes on the right. The two on the left are are the 18 & 19 hole WE and VRod bottoms. I am noticing, because of the way they had to tighten up the holes, that the Baller Head requires a bit of stirring between hits. It’s not bad and I stirred before it’s just a bit more noticeable with the Baller Head. I’m still down low at 580 so more heat may remedy this a bit. View attachment 12792
I also got three more 4mm balls down the chimney and capped that with a screen. I didn’t notice any difference but think it would be worth trying some different sized balls to see if I can’t get a carb cap effect. View attachment 12793