lol i hear ya. maybe use your pinky (not thumb) or try to insert the stem from that side..maybe the stem will roll/twist it back into place..
BAKx - bake all kinds
- Thread starter funkyjunky
- Start date
BubbleDrop
Well-Known Member
I was lucky enough to score a BAKx from the last drop and received it a few days ago.
This is such a great vaporizer, quite tiny and super light too.
I don't have a DNA mod so I configured a Sinuous P80 mod with Lamart indications and it worked quite well.
One issue is that even at low temps (185 C / 365 F), I'm getting a "Weak battery" even when fully charged (Molicel P26A/P28A). Has anyone experienced this ? It does work after all, even after a couple of warnings.
I also have a Sinuous Ravage 230 mod and installed Red Panda, but got poor results (almost no vapor with the same temp settings).
Has anyone tried this ? Here are the settings I used, maybe something was wrong.
This is such a great vaporizer, quite tiny and super light too.
I don't have a DNA mod so I configured a Sinuous P80 mod with Lamart indications and it worked quite well.
One issue is that even at low temps (185 C / 365 F), I'm getting a "Weak battery" even when fully charged (Molicel P26A/P28A). Has anyone experienced this ? It does work after all, even after a couple of warnings.
I also have a Sinuous Ravage 230 mod and installed Red Panda, but got poor results (almost no vapor with the same temp settings).
Has anyone tried this ? Here are the settings I used, maybe something was wrong.
still figuring out the cockeyed stem issue (ralph is sending me another cap rn), but i have got my dna mod in and man this thing is good. Its a nice change from my ball vapes and tinymight. I need to learn how to use this better and to change the resistance and change the celsius reading to fahrenheit though. Writing this now as im about to go on a last minute tuna fishing trip for 36hrs, hopefully when i get back i will have some sashimi and info on how to better use my bakx
El Duderino
The Dude abides.
I was lucky enough to score a BAKx from the last drop and received it a few days ago.
This is such a great vaporizer, quite tiny and super light too.
I don't have a DNA mod so I configured a Sinuous P80 mod with Lamart indications and it worked quite well.
One issue is that even at low temps (185 C / 365 F), I'm getting a "Weak battery" even when fully charged (Molicel P26A/P28A). Has anyone experienced this ? It does work after all, even after a couple of warnings.
I also have a Sinuous Ravage 230 mod and installed Red Panda, but got poor results (almost no vapor with the same temp settings).
Has anyone tried this ? Here are the settings I used, maybe something was wrong.
I use a DNA100c box mod and I’m getting the „weak battery“ message too from time to time regardless of how fully charged the battery is. Doesn’t seem to affect performance so I don’t care.
Regarding the settings: My power is a little higher (72W) and I have the resistance dialed in at 0.222 ohms for more umph - but since these are handmade devices I don’t think there are THE right settings as they all would slightly differ.
BubbleDrop
Well-Known Member
Ok ! I also didn't notice any issue. This was a bit akward though.
I tried to change the base resistance value and set it to 0.200, 0.210 and then to 0.220 but couldn't get nice results unfortunately.
It worked better with the P80 using the settings provided by Lamart (0.200 locked, TCR 185).
I wonder if some people are using the BAKx without a DNA C mod, it would be great to hear your comments and preferred setup.
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Yep still using it on the evic two mini mod without adjusting anything since getting it
tots
Member
Bonsoir, j'ai un problème avec mon bakx, habituellement il fonctionne sans problème mais là je suis parti travailler à l'étranger quelques mois et depuis mon retour, quand je mets le bakx en chauffe l'écran m'affiche une chauffe à 400 degrés c'est bizarre je ne comprends pas trop ce qui se passe... Ma box est un prédateur.. Quelqu'un aurait le nom du logiciel pour réinitialiser mon mod ainsi que comment le faire ? Ce serait vraiment super je suis triste de ne plus pouvoir m'en servir...
Dr. G
Vapman Collector*Vapman Beta Tester
Good evening, I have a problem with my bakx, usually it works without problem but now I went to work abroad for a few months and since my return, when I put the bakx on heating the screen shows me heating at 400 degrees it's weird I don't really understand what's happening... My box is a predator... Does anyone have the name of the software to reset my mod and how to do it? That would be really great, I'm sad I won't be able to use it anymore...
Mes deux cents sont d'aller sur un forum appelé Discord où vous trouverez et parlerez au monsieur qui a créé le Bakx.
My two cents is to go to a Forum called the Discord where you will find and speak to the gentleman that created the Bakx.
I am sure that someone here can also help you further...good luck with your Bakx.!
popitup
Well-Known Member
pew pew
BubbleDrop
Well-Known Member
Still trying to figure out the best settings with the P80.
Anyone using this mod as well ?
As the mouthpiece is quite short and heats a lot, I have added a fat mouthpiece for Vapcap.
Should work fine (haven't tried yet).
Anyone using this mod as well ?
As the mouthpiece is quite short and heats a lot, I have added a fat mouthpiece for Vapcap.
Should work fine (haven't tried yet).
Last edited:
Falconflys
Well-Known Member
I've used wismec mods with tubo firmware for quite a while. On tetrax's and on the bakx. Just very recently switched to a dna mod after a 1 1/2 years on the bak. What ya tryin to figure out?Still trying to figure out the best settings with the P80.
Anyone using this mod as well ?
As the mouthpiece is quite short and heats a lot, I have added a fat mouthpiece for Vapcap.
Should work fine (haven't tried yet).
BubbleDrop
Well-Known Member
It could be some kind of calibration, but even at 175°C/347°F in session mode, the AVB is completely dark whereas it is light brown with my other vaporizers.
Maybe I can try to lower the temp settings ?
Falconflys
Well-Known Member
It seems you may need your adjust the coil resistance. Try setting it to .200 or auto read resistance and subtract .020 from that number.It could be some kind of calibration, but even at 175°C/347°F in session mode, the AVB is completely dark whereas it is light brown with my other vaporizers.
Maybe I can try to lower the temp settings ?
Is tubo installed on that mod?
BubbleDrop
Well-Known Member
Yes, tubo is installed (I also have a TETRAx using another P80/tubo), with the recommended parameters from Lamart already set : 0.200 locked, TCR 185.
It is fine, but I guess I shouldn't get those results at low temps.
Falconflys
Well-Known Member
Huh...No, it shouldn't be that dark at that low of temp. My average temp. is about 425F.Yes, tubo is installed (I also have a TETRAx using another P80/tubo), with the recommended parameters from Lamart already set : 0.200 locked, TCR 185.
It is fine, but I guess I shouldn't get those results at low temps.
Have you watched the watts when warming up? Like start at 70 and level at about 10 or so?
Somthing doesn't seem right. Are you on discord? Choooo hangs there a lot and it's easy to contact him there and ask for his input
BubbleDrop
Well-Known Member
Here is how the warm up looks like (double click to Cruise) :
Anything seems wrong ?
I'm not on Discord but I guess I'll have to get there and ask Ralph what he thinks about it.
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
I wouldn't focus too much on what it is in other vaporizers... In my experience it is all relative and far from universal across such different vapes and this was no exception
Maybe I can try to lower the temp settings ?
That does look super dark, but yes I would run lower settings, if you see my early posts here I run extremely low 300-325 if dry direct maybe even less, 340 is often a finisher temp stepping for whole nug then... It is a dance of the amount of time and the heat settings though, I think it is all subjective
Falconflys
Well-Known Member
That looks good. It's how my wismec mods operate. You may want to lower the resistance if you think it's running hot.
Stonedbadger
Well-Known Member
I love to see some pictures of those teak units from the last drop!!
Dr. G
Vapman Collector*Vapman Beta Tester
I am bummed out...have not received my package from Choo yet...I asked him...he said not to worry...but, its been awhile I think.
PS I did get my extraordinary glass and wood from Z Stems...seriously a beautiful addition to the Bakx for sure. I got the Purple Heart from the drop the other day...it was just a few days ago...I used it today. AWESOME!.
PS I did get my extraordinary glass and wood from Z Stems...seriously a beautiful addition to the Bakx for sure. I got the Purple Heart from the drop the other day...it was just a few days ago...I used it today. AWESOME!.
Last edited:
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
It can take quite a while yes, and tracking is not typically that accurate, I've had some arrive really quick, but most take longer, some have taken really long... Still nothing to do, but wait as patiently as you can
Dr. G
Vapman Collector*Vapman Beta Tester
Thank you...I made the mistake of not getting tracking. So neither Choo or I can look...but, he said the same as you...be patient. I will. Thank you for your post. Good day...It can take quite a while yes, and tracking is not typically that accurate, I've had some arrive really quick, but most take longer, some have taken really long... Still nothing to do, but wait as patiently as you can
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
I never get the tracking either, that's what I mean, no point to pay extra for the tracking as it doesn't really matter, I also don't think it's much faster... A helpful estimate though has been to see the tracking of other people who ordered when you ordered, or when they received etc... But yeah, with this shipment in particular depending where you are located of course, it will take a while. Best to put it out of your mind and just be surprised one day when it shows up suddenly!