TinyMight / TM 2

[TommyDee]

This is a thought about the tube o-ring in general. Maybe my take can be confirmed - what if you left the o-ring slack by backing off the retaining ring? Does the draw tube become much easier to insert/withdraw? In that way, one could tighten the retaining ring for securing the draw tube for transport and loosen for easier access.

 

[Shit Snacks]

Bowl #5 Come On Down!

So this is where things get more aftermarket experimental... Dug out an unused clear Milaana short stem, which does indeed fit perfectly as the same diameter as the stock stem, with a basket screen from @Ratchett for RBT vapes (can't recall what size or what he calls them on his site) and no cooling unit since that is still in my stock short stem for more mobile use.

Loaded some medium ground Candyland, and started using it upside down with this awesome mini j hook from lamart tubo, riding level 3 for three lovely hits. Then bumped to level 4 for two more, and one at level 5. Smooth, tasty, no hotter or harsher than the cooling unit at these temps.

I then switched to this RBT dydrotube upright (or at a side angle-- load definitely seated securely after those first several upside down hits in the j hook, though I did not check) for the remainder:

Took another hit at level 5 like this, then two more hits at 6.5 followed by two at 8 to finish, with noticably roasted flavor now. The clouds were substantial though the vapor was still pretty smooth thanks to this wider diameter glass cooler, perhaps more tolerable than the j hook for upper temps (but unfortunately I don't think these tubes are available anywhere).

I guess basket screens may leave a darker more extracted ring here without stirring, but could also be draw dependent, too soon to tell. I did rotate the stem carefully every few hits, while glass did get a bit warm since this was again a session with back-to-back hits even though I was using on demand mode (have not tried anything else yet, not stealth mode yet either).

After this whole bowl, battery went from 3.8v to 3.66v so I threw it in my nitecore charger (which is how I am seeing the cell's level btw). If I am just using this style of load and stems, temp stepping for this many hits, I could get four bowls probably? Depending on exact settings, how much is loaded, specific usage etc. I think with smaller loads and perhaps fewer hits at maybe higher settings even, seems like up to six bowls should be a reasonable expectation... An estimate range of 2-6 bowls, with average being 4 bowls, for the included battery at least.

I have some other 18mm female glass pieces that I can now use with this stem setup, unfortunately I have an even wider variety of 18mm male glass stems (from lamart, RBT, customs, and more) that I cannot use with my TM. But I do think I have plenty other options (including bubblers and hydrotubes) to play around with, so I think I will be using this stem for a while at home now... I meant to mention with the previous bowl, at the end of doing all those back-to-back hits even below level 6 (which is the halfway mark) the entire short stem got quite hot, especially cooling unit.

 

[Siebter]

I can concur that aiming for a dark abv won't milk much more thc – my abv from a TM tend to be quite a bit lighter then what I'm having with my Dynavaps; stirring and upping the temps may result in one or 1½ more very light hits, but spoils the flow for me = not really worth it.

Maybe my take can be confirmed - what if you left the o-ring slack by backing off the retaining ring? Does the draw tube become much easier to insert/withdraw? In that way, one could tighten the retaining ring for securing the draw tube for transport and loosen for easier access.

That would leave the (edit: metal) ring loosened, which I don't find practical. The way it is now is actually quite nice, the stem can be inserted and removed with enough ease, while the o ring will hold the stem securely when inserted. You can even hold the device by the stem.

 

[Alex3oe]

So this is where things get more aftermarket experimental... Dug out an unused clear Milaana short stem, which does indeed fit perfectly as the same diameter as the stock stem,

You're genius!

Paired the TM with the ELEV8R mouthpiece using a Splinter stem as intended. Not very handy, but no cooling unit needed.

 

[Shit Snacks]

You're genius!

Thank you, but I can't take credit as it was @khelek41girl who first discovered that the RBT stems fit or at least reported it here first!

Agreed as @Siebter says, the o-ring is very secure, as it is with other handmade stem vapes that use them, here they they are also easy enough to get in and out. No complaints from me so far, but I still don't feel like stirring now lol

Okay so I'm not going to play by play every bowl, but here we have number six to finish off that Candyland grind... Took the first hit upside down at 5, still tasty but thick, so then switched to the drydro for another. I then bumped up to 8 for a hit through water, inline honeycomb rig from dhgate. I took another hit at 8 to finish, but first shut it off and turned back on in session mode, for one last long one without holding button:

Getting it into session mode was surprisingly easy, though I did have a little trouble shutting it off. Got the three clicks right on the second try I guess so not too bad really, and fortunately was able to clear the hit because the bowl was cashed at this setting (no leftover vapor).

Onwards and upwards...

 

[TommyDee]

<snip>
That would leave the (edit: metal) ring loosened, which I don't find practical. The way it is now is actually quite nice, the stem can be inserted and removed with enough ease, while the o ring will hold the stem securely when inserted. You can even hold the device by the stem.

The term "slack" is meant as a specific connotation here of 'not being loose but not being under pressure' . Sorry if I wasn't clear. I noted the comment in another review regarding a little extra effort to stir the load. To me, this is a tweakable element.

Interesting thought; if that screw becomes a furniture magnet, swap it for a Philips version of the screw. They seat deeper - fact! Is the adjuster knob dead-even with the bottom face?

 

[IAmKrazy2]

Nice @Shit Snacks - I had been using a stem as a watertool like you but was putting the cooling piece in every time. I like the idea of just putting in a basket screen and calling it a day. Good call.

 

[Shit Snacks]

Thanks @IAmKrazy2 dude I know you have plenty of these stems too! It sure is an easy way to roll through bowls (I mean the TM doesn't make that too easy though of course )

Okay okay because you all begged me for it, bowl number seven of tangie dream here with first hit at 5 through the j hook, then a couple more through the d tube, and get this I actually stirred (rather I dumped it out on the table then sucked it back in reverse direction, which is the easiest way to stir at home btw) before taking another hit at 6.5 through the j hook. Then I actually did a trick I picked up from my early Zion days and packed a tiny bit more of fresh herbs on top of the compacted-from-being-extracted load for the final hits... After another one through the j hook I then moved on to the bubbler and cranked it to 8.5 for two more:

Okay no more from me for a little while, please please no, no encore, stop all your insisting!

 

[tennisguru1]

Bowl #5 Come On Down!

So this is where things get more aftermarket experimental... Dug out an unused clear Milaana short stem, which does indeed fit perfectly as the same diameter as the stock stem, with a basket screen from @Ratchett for RBT vapes (can't recall what size or what he calls them on his site) and no cooling unit since that is still in my stock short stem for more mobile use.

Loaded some medium ground Candyland, and started using it upside down with this awesome mini j hook from lamart tubo, riding level 3 for three lovely hits. Then bumped to level 4 for two more, and one at level 5. Smooth, tasty, no hotter or harsher than the cooling unit at these temps.

I then switched to this RBT dydrotube upright (or at a side angle-- load definitely seated securely after those first several upside down hits in the j hook, though I did not check) for the remainder:

Took another hit at level 5 like this, then two more hits at 6.5 followed by two at 8 to finish, with noticably roasted flavor now. The clouds were substantial though the vapor was still pretty smooth thanks to this wider diameter glass cooler, perhaps more tolerable than the j hook for upper temps (but unfortunately I don't think these tubes are available anywhere).

I guess basket screens may leave a darker more extracted ring here without stirring, but could also be draw dependent, too soon to tell. I did rotate the stem carefully every few hits, while glass did get a bit warm since this was again a session with back-to-back hits even though I was using on demand mode (have not tried anything else yet, not stealth mode yet either).

After this whole bowl, battery went from 3.8v to 3.66v so I threw it in my nitecore charger (which is how I am seeing the cell's level btw). If I am just using this style of load and stems, temp stepping for this many hits, I could get four bowls probably? Depending on exact settings, how much is loaded, specific usage etc. I think with smaller loads and perhaps fewer hits at maybe higher settings even, seems like up to six bowls should be a reasonable expectation... An estimate range of 2-6 bowls, with average being 4 bowls, for the included battery at least.

I have some other 18mm female glass pieces that I can now use with this stem setup, unfortunately I have an even wider variety of 18mm male glass stems (from lamart, RBT, customs, and more) that I cannot use with my TM. But I do think I have plenty other options (including bubblers and hydrotubes) to play around with, so I think I will be using this stem for a while at home now... I meant to mention with the previous bowl, at the end of doing all those back-to-back hits even below level 6 (which is the halfway mark) the entire short stem got quite hot, especially cooling unit.

Maybe something from here?
https://www.dhgate.com/product/glas...tml?skuid=439871470072352768#cart_view-8-null

 

[Easywider]

@Shit Snacks loving the play by plays! Great way to start the new year. The darker ring that happened when using without the CU and using a basket screen is this present at all when using the CU ? Does using session mode reduce the ring at all? I have another vape that uses a very similar coil design and it's plagued by the ring. Maybe I can fix it when my TM with extra CU arrives

Thanks for experimenting and sharing your results!

 

[MonkeyTime]

@Shit Snacks loving the play by plays! Great way to start the new year. The darker ring that happened when using without the CU and using a basket screen is this present at all when using the CU ? Does using session mode reduce the ring at all? I have another vape that uses a very similar coil design and it's plagued by the ring. Maybe I can fix it when my TM with extra CU arrives

Thanks for experimenting and sharing your results!

I'll be interested to hear @Shit Snacks answer, but I've only found that ring when going thru water or really honking on it, cooling unit or not.

I can also correct my earlier post, I was pushing medium BCG grind thru it to start, not fine. I tend to grind in larger quantities and should have checked the grinder before speaking! I have since changed to the fine and will probably stay there for a bit to keep from changing too many variables at once.

I tried a few of my ELB's last night, most of them didn't fit. The only one I did it that the body of the elb for into the stem, the neck was too large and left a 1mm gap. I tried it install the stem just to see how it worked with the o-ring, and I had to disassemble the heating chamber to get the cap out... It got pulled loose trying to remove it.

I've tried all the capsules I have, so far none of them have fit well enough to recommend. Are the MV capsules the only confirmed to fit?

This one shows enough promise that I'm shelving my other vapes while we get aquatinted, maybe another week.

 

[dzoinp]

My TM review:




...end

 

[RelaxedNow]

I ordered a Tinymight about 10 days ago, before the o-rings were available. When I found out they are now sold as an accessory, I emailed a request to have them added to my order. Today, I received a reply and a modified invoice, which now includes them. Positive service experience thus far.

On a related note, it’s looking like mine will be shipped in about 2+ weeks. No promises, but I’m ok with that. Definitely looking forward to trying it out.

 

[YaMon]

I ordered a Tinymight about 10 days ago, before the o-rings were available. When I found out they are now sold as an accessory, I emailed a request to have them added to my order. Today, I received a reply and a modified invoice, which now includes them. Positive service experience thus far.

On a related note, it’s looking like mine will be shipped in about 2+ weeks. No promises, but I’m ok with that. Definitely looking forward to trying it out.

I had the very same experience today.

 

[Easywider]

Same here, just last week. Emailed about an extra CU and O-rings, had a reply with an updated invoice in 15mins. Incredible.

 

[IAmKrazy2]

The heat consistency is among the best of any portable. Really can't scorch or hot spot at all with the stock stem and something about the actual temp consistency reminds me of the Herbalizer which is (was?) the king of temp consistency.

Something unique about a portable with this type of temp consistency in conjunction with instant convection.

Excellent "vapor signature" too - great flavor and effects from a fully clean stem.

 

[RelaxedNow]

The heat consistency is among the best of any portable. Really can't scorch or hot spot at all with the stock stem and something about the actual temp consistency reminds me of the Herbalizer which is (was?) the king of temp consistency.

Something unique about a portable with this type of temp consistency in conjunction with instant convection.

Excellent "vapor signature" too - great flavor and effects from a fully clean stem.

A comparison to the Herbalizer!

I love my Herbalizer, but I rarely use it, as it’s a desktop unit. If the Tinymight comes even close in terms of flavor and temperature-controlled buzz, it’ll be a winner.

 

[Brewervapesalot]

A comparison to the Herbalizer!

I love my Herbalizer, but I rarely use it, as it’s a desktop unit. If the Tinymight comes even close in terms of flavor and temperature-controlled buzz, it’ll be a winner.

I agree. My Herbalizer is getting much less use.

ABV. I get darker ABV with an ELB versus just a pipe screen. Flavor is better without a ELB or capsule. And I do like just filling the stem by sticking it directly in ground herb.

Herbalizer has better flavor, but we're talking on the margins here...

The best comparison I stand by:

The Tiny Might is a portable (instant on) Evo (Evo wins performance wise, but not massively)

- no learning curve.
- nice analog dial for temp that works well.
- holds ELBs
- big tasty clouds
- not finicky

 

[Ramahs]

I agree. My Herbalizer is getting much less use.

ABV. I get darker ABV with an ELB versus just a pipe screen. Flavor is better without a ELB or capsule. And I do like just filling the stem by sticking it directly in ground herb.

Herbalizer has better flavor, but we're talking on the margins here...

The best comparison I stand by:

The Tiny Might is a portable (instant on) Evo (Evo wins performance wise, but not massively)

- no learning curve.
- nice analog dial for temp that works well.
- holds ELBs
- big tasty clouds
- not finicky

 

[dzoinp]

My TM arrived yesterday ... Now that I've empty 3 sony vtc6 I've figured out why it didn't arrive before ... TinyMight is not a vape of the past decade. It is a vape of the future as long as it has been running consistently for a long time. Can be sure
I use a kind of doob tube to top up my daily used crafty. With the TM is the same but takes about 1/3 of the greens. You can add more but I do not advise ...but... can always repeat the dose
Weighs 184gr with the battery and short stem, 42gr more than the crafty and is about 20mm shorter
Steam with short stem + cooling unit is colder than long stem with domed screen only, however here the steam is stronger and a little tastier. I like it both ways.
I've been using it at temp 6 ... very nice to change just by turning the button, after 3/4 hits the steam is gone but you can always stirr and / or increase the temp. Stirr sucks with TinyMight, unlike e-nano for example. At Tm the greens are at the very end of the stem and when stirring spreads the browns.
In my opinion TM is an on demand vaporizer ... crafty/mighty is a better session vape because it takes twice or triple the material.
When it's cold on dial 6 it takes 7sec to vibrate ... if it doesn't take long the next heats are 2 / 3sec not even that! incredible!
Good, but here is the first point to improve:
When the heater is warming up, it makes a noise (bzzzzxxxxx) during the day in the car I heard nothing but sitting on the couch you hear a lot.
Taste is very good I think better but similar to e-nano, with the cooling unit makes it quite comfortable on short stem. Plenty, crafty, mighty may have better flavor but with much more greens and only on the first hits!
Another thing that could be improved is the button location i preferred on the other side like in crafty...
I love the light and the vibration that is not very aggressive, just enough to feel when you have it in your hand ... lol
The light can be seen from anywhere regardless of where you place it and the reflection on the stem is beautiful.
I have not mentioned that this vape is beautiful just looking at it I'm happy, but anyway I still enjoy looking at my wife more ... is much prettier and gives me much more ...
Monday T80 arrive after two weeks at customs!!... I'm a luckie man

 

[SquirrelMaster]

Just ordered a Tinymight to Canada! Hopefully it makes it through without many/any duties which have been hit or miss lately for me. Stickstones piqued my interest when he first posted about it on Instagram but my VAS could only hold so long. Plus I "need" a new dog walking vape so really this a vape for the pups . Extra short stem, long stem, cooling unit and o-rings were added and I asked about screens as well since I didn't see them on the site. I like to stock up.

The Mistvape Imp dosing caps seem like they're the best/only dosing cap option correct?

 

[Alex3oe]

The cooling unit sucks, mod nipple or multiple path stems or something for cooling please

Didn't much bowls in the original stem with the cooling unit, maybe 10, max 15. At this point the cooling unit wasn't barely movable any more in a cold stem, it stucks in the resin.

When I read about fitting RBT stems (sadly not all fit) I started experimenting, using Lamarts bent stem connected to the RBT stem as my favourite setup now. When I used the original stem today, there was a noticeable lack of vape density and taste from the very beginning. Switched the load to the RBT stem after some draws, much better.
Opened the cooling unit and it's covered with so much resin already, surprised me after this few bowls. As good as the unit cools, as much resin it seems to catch, leading to reduced airflow, taste and potency quite fast

 

[Siebter]

@Alex3oe - What temps are you using? I'm able to move the cu even after 25 sessions easily. Might be dictated by the strain and / or temp, though. I'm usually at about 7.

Edit: Also very interesting to see how low temps are used by others, will give that a try as soon as my t break is over.

 

[Weedcutter]

The VAS hit me and I placed an order
I have a DV Ascent, GH, Mighty, Cano Digital and a couple of Dynavaps since before
Can’t wait to see how it compares
Fun fact, dynamite pronounced with a Finnish accent becomes tiny might

 

[Alex3oe]

@Alex3oe - What temps are you using? I'm able to move the cu even after 25 sessions easily. Might be dictated by the strain and / or temp, though. I'm usually at about 7.

I have to vape with at least 30% hash, depending on weed availability, it goes up to 80%-90%. This leads to more dirtparts and resin in general, so it plays a role for sure
And that's why I'm needing higher temperatures as well, I'm starting at ~5-6, allways going up to 10 to get the last 1-3 puffs out.