Discontinued Omicron Vaporizer for oils

OF

OF

Well-Known Member
THC SCIENTIFIC said:
yes we kept the update and as more carts are produced they will have it. But now im not sure about the second generation carts keeping this update. We shall see.

Also taste test carts are 4.0
Click to expand...

OK, that got a little scrambled from your brain to mine over Al Gore's internet. So old styles are disappearing and the new style will continue to fill the product stream until the release of the next generation which is still a ways off and might or might not include this blind ended tube change?

<Deep breath>

Then I got lost, I know the taste test carts are four Ohms.....did you mean me to understand that they are the new style?

Thanks once again, big guy.

OF
 
OF,
THC SCIENTIFIC

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
OF said:
OK, that got a little scrambled from your brain to mine over Al Gore's internet. So old styles are disappearing and the new style will continue to fill the product stream until the release of the next generation which is still a ways off and might or might not include this blind ended tube change?

<Deep breath>

Then I got lost, I know the taste test carts are four Ohms.....did you mean me to understand that they are the new style?

Thanks once again, big guy.

OF
Click to expand...

Yes on first part.

No on the second, the taste test carts had the metal air tube on the bottom but are not the version 2 carts, that was finally assembled yesterday and being shipped out Monday.

That goes into testing soon as i get em. But it should take care of the leaks and clogs.
 
Zingbuddah

Zingbuddah

Vaporologist
jambandphan03 said:
use pliers or tongs to hold the cart so you don't burn your fingers, or even a thick glove would work...you could also find a way to mount/clamp it to something and then heat it w/ blowdrier...a few ideas anyway...
Click to expand...

I disagree...I think you need to hold on to the bottom of the cart with bare fingers as you gently heat the funnel and top 1/3 of the cart. Using your bare fingers ensures the temp stays where seals and electrics have zero chance of failure. I'm using a MAPP gas torch when I do this and I'm able to fill .8g with no issues while holding the cart. Leveraging time instead of effort in this case (wait for the oil to flow instead of heating it longer and hotter) works out in your benefit.

Then again...YMMV

-Z
 
Zingbuddah,
  • Like
Reactions: DubCRider
S

shortwind

Well-Known Member
THC SCIENTIFIC said:
Sorry boss i missed it can you pm me your issue and let me see if i can help.
Click to expand...

Here's what I wrote earlier today:

Update. I checked my cartridge this morning and now there is a big blob of goo coming out of the bottom. Yesterday, I went to vaperpedia and did all the steps noted to get rid of a clog. I did hear popping sounds several times, but after all that the device heated up, but little or no vapor came out and now stuff is leaking out the other end. What steps should I next take???
Thanks!


Here's an addendum: after tons of priming and cleaning all the goo off of stuff with ISO and q tips, I got some vapor out of it this afternoon. Will try again later and see if it is still working.
 
shortwind,
B

bombaysippin

Member
Is THC online right now? I have a defective Omicron Original charger again. This time it lasted 2 months+... I filed a ticket yesterday no response, I take it no business on the weekends? In all still very happy with the product, the faulty charger has been the only negative.
 
bombaysippin,
W

Wildcajun

Member
Fter charging the Battery and filling the chamber with .5 grams of oil blue light would flash 3 times took back apart cleaned all areas good recharged batteries and still blue light flashes 3 times never heats chamber ?? any ideas?? Cajun
 
Wildcajun,
THC SCIENTIFIC

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
shortwind said:
Here's what I wrote earlier today:

Update. I checked my cartridge this morning and now there is a big blob of goo coming out of the bottom. Yesterday, I went to vaperpedia and did all the steps noted to get rid of a clog. I did hear popping sounds several times, but after all that the device heated up, but little or no vapor came out and now stuff is leaking out the other end. What steps should I next take???
Thanks!


Here's an addendum: after tons of priming and cleaning all the goo off of stuff with ISO and q tips, I got some vapor out of it this afternoon. Will try again later and see if it is still working.
Click to expand...

Is it possible to weigh the cartridge?


bombaysippin said:
Is THC online right now? I have a defective Omicron Original charger again. This time it lasted 2 months+... I filed a ticket yesterday no response, I take it no business on the weekends? In all still very happy with the product, the faulty charger has been the only negative.
Click to expand...

Please check your spam or junk folder, we have a ticket system and if you submitted a ticket we should have gotten to it. If no response please provide me with a ticket number and ill see what happened.
 
THC SCIENTIFIC,
Xchadb

Xchadb

@Brownglass
Glass Blower
sucks, i see a LOT of posts with problems... but a lot of people getting answers :tup:

because all my carts work perfectly!(even with tons of bong use) :science: thanks again G for this awesome cartridge.
 
Xchadb,
  • Like
Reactions: Jay420
jambandphan03

jambandphan03

in flavor country
not getting any real problems here either, occasional little primer 'pop' clog that clears up once I get it warm. Nothing serious.
 
jambandphan03,
DubCRider

DubCRider

Well-Known Member
Test all carts at 3.7v. That means with your Omicron or Persei with 18650 battery. With a 3ohm or higher you will need to feel for the heat rather than look down the air path for the glow.
 
559stonerr

559stonerr

Well-Known Member
just ordered my omicron v2 from planetvape.. accidentally ordered two on accident.. will be resolving the issue with PV. can't wait till i can test this baby out!:tup:
 
hatfieldsmama

hatfieldsmama

Active Member
DubCRider said:
Test all carts at 3.7v. That means with your Omicron or Persei with 18650 battery. With a 3ohm or higher you will need to feel for the heat rather than look down the air path for the glow.
Click to expand...

in regards to 3 ohms and higher, simply feeling the heat does not signify a working cart. the wick down the tube needs to be functioning for the cart to be working properly. only way i know of to make sure the wick works is by looking down the tube for the red glow....
 
hatfieldsmama,
DubCRider

DubCRider

Well-Known Member
Go ahead and burn your carts out at 7.4v checking then....

I've tested a few carts not only for myself, but others too this way with great results. I have also burned out carts checking at 7.4v on accident and in the beginning. If it gets warm it will work.
 
DubCRider,
hatfieldsmama

hatfieldsmama

Active Member
DubCRider said:
If it gets warm it will work.
Click to expand...

thats simply not true.

edit: i never said to check at 7.4 volts. i just said you need to check for the red glow..... carts that are burnt out still get warm. i have received carts that never lit up from the start fwiw
 
hatfieldsmama,
Sinclue

Sinclue

OK disagree with me, I can't force you to be right
As I understand it the newer pre-oxidized carts we tested are just entering the consumer stream. There are plenty of the older style around (I have several) that still need to be pre-oxidized per G's instructions.
 
Sinclue,
rusty shacklford

rusty shacklford

Member
is this new cart going to be able to handle thinner oils like RS/co2/iso without leaking or clogging ???



ilovedoobies! said:
DSC_0292.jpg
Click to expand...
 
Indicana_Jones

Indicana_Jones

Member
Zingbuddah said:
I disagree...I think you need to hold on to the bottom of the cart with bare fingers as you gently heat the funnel and top 1/3 of the cart. Using your bare fingers ensures the temp stays where seals and electrics have zero chance of failure. I'm using a MAPP gas torch when I do this and I'm able to fill .8g with no issues while holding the cart. Leveraging time instead of effort in this case (wait for the oil to flow instead of heating it longer and hotter) works out in your benefit.

Then again...YMMV

-Z
Click to expand...

I have adopted a similar method, I used to heat more aggressivly for a faster melt in but I'm using my torch still and coaxing it down. I add a few tenths of a gram at a time keeping my 5 ohm cart right around a half gram or slighly under and other than some clogging of the tube which clears easily enough I have no issues. My 2.4 cart clogs at the other end and clogs full. I'm not sure how much more use I'll get out of that cart now. My cart has gotten hot to the touch at the 1/3 point when filling though, not hot enough to burn but hot enough to be uncomfortable.

Wildcajun said:
i have a 1.5 cart and a 2.4 cart how do you test them do they go bad ?
Click to expand...

Carts will fail! The wicks can clog or the heating elements burn out. Voltage tests can tell you something if you have the equipment and understand those things. No vapor is a good indication that there is something wrong. If there's oil, a good battery and you're hitting it proper but getting no vapor.. I'd say cart.. But I'm new.

Cheers!

Indy.
 
Indicana_Jones,
Dgtheonlyg

Dgtheonlyg

Active Member
THC SCIENTIFIC said:
Ok guys update on HVD just checked tracking number, if i can understand this mumbo jumbo it says its being delivered to our shipping center tomorrow or Tuesday. Soon as we get it its going out.
Click to expand...

This just made my moring! Can't wait!

G is d9 having a booth at hempcon? it's comming up soon
 
Dgtheonlyg,
You must log in or register to reply here.
Top Bottom