Discontinued VapeXhale Cloud EVO

vaporeyes444

New Member
Do you crank it up all the way? How do you deal with the excess bubble left over? It worked great first hit w/ the two cap method but then not as well after that
 
vaporeyes444,
I run pretty hot, some times max, sometimes 3. When I'm vaping bubble, I'm going for quick one hitters most the time, so I normally keep the load small, so quick extraction is possible.
Also, depending on how melty your bubble is, you might benefit from some SS concentrate pad in the top cap. This gives it somewhere to go, instead of sucking through the screens.

@VnS, non fullmelt bubble vapes easier than fullmelt. The non melty properties allow air to travel through it, which gives nice convection vapage. While full melt will melt and have its heat zapped by the elb, in turn makes it convection with a healthy assist from conduction.
 

vaporeyes444

New Member
I run pretty hot, some times max, sometimes 3. When I'm vaping bubble, I'm going for quick one hitters most the time, so I normally keep the load small, so quick extraction is possible.
Also, depending on how melty your bubble is, you might benefit from some SS concentrate pad in the top cap. This gives it somewhere to go, instead of sucking through the screens.

@VnS, non fullmelt bubble vapes easier than fullmelt. The non melty properties allow air to travel through it, which gives nice convection vapage. While full melt will melt and have its heat zapped by the elb, in turn makes it convection with a healthy assist from conduction.
What is an sS concentrate pad and where do i find them?
 
vaporeyes444,

mvapes

Scratchin' Glass!
Accessory Maker
I've started flattening out some hemp cotton and throwing some shatter in it. Then smash it in to outside of an ELB lid. With an empty ELB otherwise and your temp cranked to like 2:30+ - I promise your going to see fog like your in fucking San Francisco!


The flavor is off the charts, unless you got some shitty oil, but from what I've used it's been pretty dope!

Arty-Brilliant-Ingenious-Hand-And-Finger-Painting-23_zpsf7c58881.jpg
 

vaporeyes444

New Member
I had some thoughts on the evo and bubble hash. I'm concerned that withthe increased airflow we use with the evo that we are actually wasting much of the hash. You can see how messy using bubble hash in the cloud can be, it also seems to dissappear quite quickly. I noticed this too with the bho i used and I was concerned that much of the waxy nature of the bho splattered everywhere before being vaporized, some on the hydratube and some possibly in my lungs. I hope that the hash ez load bowls will address these concerns. Overall pretty happy with the evo and hydratube. Out of curiosity, how hard do you guys pull when hitting it? Is it whistling, faint whistle, no whistle?
 
vaporeyes444,

530rasta

Well-Known Member
not sure if it works for the evo as im still waiting for mine (preorder meh) but for my solo i just make a small flat hash patty and sandwich it in between a couple tiny pieces of herb, works awesome and even if its fmcd, the hash doesnt just flow down into my solo bowl, might work for the evo fwiw
 
530rasta,

m0sh

Singer Song Writer Stoner
Hey guys and XVL

As I'm waiting for my international EVO, I have a small question.
Is it possible to receive some sample of legal herbs like lavender and such?

Cheers!
 
m0sh,
  • Like
Reactions: Silent

elmomuzz

That just happened...
My cloud is really being tested. I keep it outside in a unheated shed. This morning it was -0.3 degrees Fahrenheit when I went for my first shed visit. I keep a 5 gallon bucket covering the evo and hydratube so that the water doesn't freeze. I have to turn the evo to maximum but it can turn the green to brown with 0 degrees intake air temp!
 

mvapes

Scratchin' Glass!
Accessory Maker
So this question has been asked a lot since I got an Herbalizer. How do they compare? I tell evryone the same thing, they don't. Two completely different worlds!

IMO, if I could show a picture that best sums up Herbie it would be...

2003-Rolls-Royce-Phantom.jpg


Now if that same question was asked about the EVO than I would go with...

muscle-car-engine-showdown-9.jpg


I hope this clears things up.
 

JoeKickass

Well-Known Member
I notice my evo seems to be colder than when I first got it, it turns green on max, and I get wispy vapor where I used to get a regular hit. Seems to take longer to get up to performance.

However, I have used a single ELB nonstop since I got it. So I'll try a new one next time, does a dirty ELB make the unit act cold? (thinner vapor)
 

Nevertheless1090

Well-Known Member
I notice my evo seems to be colder than when I first got it, it turns green on max, and I get wispy vapor where I used to get a regular hit. Seems to take longer to get up to performance.

However, I have used a single ELB nonstop since I got it. So I'll try a new one next time, does a dirty ELB make the unit act cold? (thinner vapor)

In my opinion, it's like maintaining your car's oil. Sure, it will still run but the longer you don't change your oil (ELB, clean or change), the more your car's performance will diminish.

I try to clean my ELB every two days. Your cloud device will combust the ELB is incredibly dirty.
 
Top Bottom