I can attest to kief (not hash - it’s been way too long sadly since I’ve had hash). Kief works wonderfully! I load it in before regular ground flower so it’s not adjacent to the heater screen, lightly tamping the load down. I haven’t tried just kief by itself for fear of any particles falling through the heater screen into the heater, hence the flower on top. I suppose kief-only could be done if packed tight enough (which may hamper draw resistance and air flow a bit). Kief however is kool in the TM!How’s the tiny handle hash and kief?
I’m rotating through 8 batteries.
@LAWTHEONE – There is a secret way to tune your TM higher and lower, but you will have to ask the maker about it and let him decide whether that's a good way to cope with your problem.
Hello everyone. I have two quick questions.
1) Does the tinymight work with the E nano water adapter?
2) I thought I heard of a way to turn your tinymight higher or lower? Other than the dial of course. If there’s a way can someone explain how please? I’m looking to turn mine up to make it hotter, because I feel like it cooled off suddenly? Still works just not as hot and hard. I’m rotating through 8 batteries.
There was some discussion of lowered performance a page or two ago (and earlier in the thread) and since it was resolved with some of our suggestions it’s probably worth a read.
The secret method only works on newer models. I tried it on my older model TM and it didn't work. I haven't tried it on my newer model TM because it vapes at temp 5 the same way my older TM vapes at temp 7.
Hello everyone. I have two quick questions.
1) Does the tinymight work with the E nano water adapter?
2) I thought I heard of a way to turn your tinymight higher or lower? Other than the dial of course. If there’s a way can someone explain how please? I’m looking to turn mine up to make it hotter, because I feel like it cooled off suddenly? Still works just not as hot and hard. I’m rotating through 8 batteries.
Thanks everyone
1. I would say no....does not look like it is 16mm OD. which is needed to fit the TM.
2. You would have to explain exactly how you use your TM and then we can see what might be your issue.
If you were combusting that easily, I have to ask: when you hold the button down, are you waiting for the single vibration before starting to draw? Because if you don't wait for that vibration, the heat you get will be inconsistent, possibly to the point of combustion.I got my TM in February. I actually struggled with using it at first because I could come bust a bowl on level 6-7. I can’t stand the way combustion smells. I would have to clean the bowl out each time so this made me put it on the shelf for a little. I went back to a few of my other Vape‘s that I could get more consistency with.
I got my TM in February. I actually struggled with using it at first because I could come bust a bowl on level 6-7. I can’t stand the way combustion smells. I would have to clean the bowl out each time so this made me put it on the shelf for a little. I went back to a few of my other Vape‘s that I could get more consistency with.
In June I started using my TM and Tetra X mostly. In July I started using my TM exclusively. I started getting my technique down so I combusted hardly ever. I would use anywhere from 6 1/2 to 7 1/2. Then maybe a week ago I felt like it wasn’t giving me the same extraction at those levels. So I bumped it up two 8 1/2, then two 9 1/2, and now I’m on 10. 10 was working great but now it seems like it has cooled off and it’s virtually impossible to combust even on 10 even with a long & slow draw.
I have a total of eight batteries but I really only rotate through seven of them. Someone said rotating through seven is to many so I am going to try to rotate through three now. It’s definitely not the same from when I could combust so easily on power 7.
Thank you to everyone answering my questions and giving me a hand with this. It’s greatly appreciated.
Since the first day i got it, it sounds like something is moving inside I figured it was just the metal tube in the chamber with its little wiggle room it has, maybe it is.
Haha yeah I also use the all glass wpa from TM official, cleaned my water pipe also to make sure the percs were unclogged. Well if there should be no noise I believe my unit came slightly defective and what ever is making that noise must be the culprit, sounds like something small probably connected with a wire is moving freely. I had assumed it was normal because mine seemed to function normal. It won't void my warranty if I open the bottom where dial is and see what the noise is will it?You guys got a clean screen and CU right? The impact of a dirty screen on a convection vaporizer shall not be understated!
Blu-Tac! Works for my Hopper (all threads) but haven’t needed to use it on my Tinymight. Good luck.and something that will get into the threads.
I've tried that. Here was my checklist.@LAWTHEONE & @iDRINKBLEACH
From what I'm hearing so far, I'd start with a very thorough cleaning of the battery lid and threading it screws into. Iso and something that will get into the threads. Verify the battery terminals are clean and they're fully charged. Then pictures of your stems, the pack/grind, etc. like was just asked.
It sounds like you're getting inconsistent results from poor power delivery (dirty contact points) and possibly packing/setup hurdles.
I've noticed a slight drop in performance a couple of times, each time a good cleaning brought it back to it's normal awesomeness.
Let's get you guys straightened out already, too much experience and talent here for this! Unless of course there is just a physical issue, but not guessing that to be the issue.
It's been quicker of late. Speaking generally it's around two to four weeks or less if he's still stocked up. Mine was two weeks and change a few months ago.Hey does anyone know the current approximate wait time? My solo II is crapping out and hoping to get a TM before it’s completely unusable
In June I started using my TM and Tetra X mostly. In July I started using my TM exclusively. I started getting my technique down so I combusted hardly ever. I would use anywhere from 6 1/2 to 7 1/2. Then maybe a week ago I felt like it wasn’t giving me the same extraction at those levels. So I bumped it up two 8 1/2, then two 9 1/2, and now I’m on 10. 10 was working great but now it seems like it has cooled off and it’s virtually impossible to combust even on 10 even with a long & slow draw.
I have a total of eight batteries but I really only rotate through seven of them. Someone said rotating through seven is to many so I am going to try to rotate through three now. It’s definitely not the same from when I could combust so easily on power 7.