vapviking
Old & In the Way
Beautiful job! Nice design.
For a while I used Mighty like a plug-in, your stand would be perfect for that use.
The Mighty/Mighty+ by Storz & Bickel
- Thread starter Roger D
- Start date
Beautiful job! Nice design.
For a while I used Mighty like a plug-in, your stand would be perfect for that use.
seatsniffer
Well-Known Member
Awesome, that's way nicer than the stand I printed before and have been using. This will be the first thing printed when I get time to fix the thing.
ChooChooCharlie
Well-Known Member
Think these are around 2 and 4 yr olds, got lots of use with smokebuddy in hotels, less lately, couple times a week. And, uh, don't think I've cleaned in a couple years, gross skid marks on the right
Always capsules, and I'm one of those FC kooks who remove the cooling unit screen. Pack caps slightly over, lid compresses load, this avoids herb bits from shifting during use. Only tiny bits near lid holes at session start have any passage opportunities
Use cotton swab or piece of paper towel twisted, immediately after dumping hot capsule, clean resin from cooling unit inlet edges especially -- actually the reason for my madness -- before I removed CU screen years ago, the capsule lids would get resin sticky. The damn CU screen accumulated condensed resin, which transferred to capsule lid, grrr, sticky capsule lids are the worst!
No damage to any plastic on mine. Never had plastic failures on old Crafty's either. Got first decent vape, Crafty, after lurk reading FC before I joined. Remember reading and seeing pics around 2015, warning users to handle CU carefully when opening and closing
It made an impact on me, and I practiced opening and closing my new Crafty
Examined the CU-to-chamber locking design, the sloping modified bayonet friction fit, the large silicone O-ring around chamber base which compresses and seals CU in place
I press down slightly when twisting open or twisting shut. You can feel the silicone O-ring compress as you press -- this way the plastic sloping tabs are not under any shearing type stresses
I also twist CU slowly. Less stress. Odd to me that every Mighty or Crafty use video or stream I watch, they quickly twist, no downward pressure, no care. Even see folks using CU to tap, rap load out, ugg
Edit: remember Bud calling me out by my choo user name in a livestream, reacting to my condemnation of his rough handling of mighty CU, rapping out load, extra hard, for my viewing “benefit”
I’m a hopeless ocd nerd
Last edited:
BiPolarBear
Well-Known Member
I had a worse case of this plastic breaking. No receipt. Also after 2 years. I registered the serial number and device on their site and they give you an extra year warranty for doing so. I then sent it in. Everything worked fine but A LOT of wear n tear n plastic bits off everywhere/structural rigidity was gone. I just got my new one today shipped to my door as a replacement. Stoked. Hopefully this helps you.My Mighty is disintegrating! A piece has broken off of the lip on the main body which engages the cooling unit. I have not dropped it, and I've never misaligned the cooling unit or the loading tool. I never even encountered any resistance installing either piece. This has always been my worry about a plastic device, especially one where the plastic bits are exposed to repeated heating.
Has anyone else had this problem, and do you know if Storz and Bickel considers it a warranty issue? Mine is two years old, but I don't have a receipt. I'm not even sure where I got it (Puffitup, I believe), though I do have the original packaging.
Thanks!
Last edited:
ChooChooCharlie
Well-Known Member
I'm sure most of you Mighty owners are aware of this "battery-saving feature," apologies if it was discussed years back
I got distracted while in boost mode, which is very rare
It buzz-warned me. I get that
But it also kicked me out of boost mode. Why?
Why not just buzz-warn me and leave me in boost. Am I a first world problem complaining, lazy wuss? Please don't answer that
When in Boost mode, after idle of 1 min 30 sec, get a short buzz and you're booted outta boost, then buzz at 1 min 45 sec, then 4 more from 1 min 50 to 55, then off. In regular, non-boost operation, first warning buzz at 1 min 45 sec, then 4 more from 1 min 50 to 55, then off
I got distracted while in boost mode, which is very rare
It buzz-warned me. I get that
But it also kicked me out of boost mode. Why?
Why not just buzz-warn me and leave me in boost. Am I a first world problem complaining, lazy wuss? Please don't answer that
When in Boost mode, after idle of 1 min 30 sec, get a short buzz and you're booted outta boost, then buzz at 1 min 45 sec, then 4 more from 1 min 50 to 55, then off. In regular, non-boost operation, first warning buzz at 1 min 45 sec, then 4 more from 1 min 50 to 55, then off
vapviking
Old & In the Way
In the old days we didn't even have boost mode, times were harder but somehow we liked it that way.
...and I'm still using that old Mighty!
ChooChooCharlie
Well-Known Member
@vapviking -- You're right. I'm complaining about boost and warning buzzes, features S&B added for our benefit
Yes, I remember walking five miles to the parole officer appointment, uphill both ways
Yes, I remember walking five miles to the parole officer appointment, uphill both ways
simplywonderful
Well-Known Member
one year of warranty + for the mighty? can anyone else confirm? I thought it was for crafty +
Thick Vape
In the Ballpark
So it came to my attention that the Mighty + is a reality. Sorry if has been said already.
They mention it in the video on the storz-bickel site. It should be available soon.
It even looks like they have some other stuff in petto at storz&bickel
They mention it in the video on the storz-bickel site. It should be available soon.
It even looks like they have some other stuff in petto at storz&bickel
justcametomind
Well-Known Member
Seems like it will launch in a few months, I was anticipating and gave for sure a pre-Xmas launch, but this doesn't seem possible anymore.
My dream would be a 20 seconds heat up time, same as a Fury 2. Then I would take a Mighty in rotation again.
@simplywonderful IIRC it's 2 years.
Thick Vape
In the Ballpark
Ah, so that is old news. Well "soon" can mean alot. I would love a faster heat up too.
I hope the other things they seem to have in their pipeline are bigger things than just 1 gram capsules for the volcano/plenty or something like that.
Edit:
From the S&B Website:
"Due to the company’s continued growth, the extension of the West Wing was also started at the beginning of 2020 and is scheduled for completion mid-2021. The West Wing will primarily be used to expand the production area and introduce additional production lines for new products."
It might take a couple of month more until new products arrive. Not sure the mighty + needs a new production line.
Last edited:
iammyself
Well-Known Member
I got one after I dropped and broke my glass wpa. It’s currently sitting in my long-term storage drawer, I got a replacement glass one. Maybe it’s just my rattle can water piece, but the rubber delta 3D one would get stuck every time I tried to clear the chamber. I even had it rip off a couple times, and some of the bowl spill out. I also felt like I have to position my pinky on it while drawing to make sure there was a solid seal.
I know it’s recommended to avoid breaking your Mighty, which can happen with the glass adapters. But the rubber wpa required too much finesse for me.
vapviking
Old & In the Way
I use the Delta3d v3 wpa and like it a lot. Occasional sticky-ness of silicone to glass, as @iammyself mentions; sometimes I rub a little veg. oil, or some wax on it. I find it more a matter of technique/finesse in how you remove it. It can also spin out of the Mighty during removal from glass, so there's that.
But with those two potential pitfalls I find if I do it carefully, no problems. And neither can result in breakage to glass piece or Mighty. I am usually leaving Mighty on the glass throughout a bowl, so I don't encounter the stickiness with every hit, just at the end, if at all.
I definitely feel it is safer using this on the Mighty than the glass adapters are, because,
I see two pitfalls to the glass adapters. First is the one commonly pointed out, that simply over-tightening when mounting it to Mighty can cause cracking on Mighty. The second is, when mounted and glass piece is added, there is a lot of leverage potential against the Mighty's housing. The other (delta) wpa is 'break-away', will just pop off if under stress, rather than break the housing.
Moses Baca
Colorado State Reformatory #8755
I agree with @vapviking , I love my D3D Studios wpa. I haven’t used my glass wpa since I got it.
Both work. There’s technique involved with any wpa but the silicone reduces chances of me damaging my Mighty.
Both work. There’s technique involved with any wpa but the silicone reduces chances of me damaging my Mighty.
Last edited:
iammyself
Well-Known Member
I don’t really use my mighty in water often, so I never bothered to investigate further what was causing the silicone delta 3D wpa to stick so bad in my rattle can. I have a bit of a sore throat right now, and a kind of harsh-vaping quarter of ground flower, so I just broke it out of storage to give it another try.
I used a 18mm to 14mm reducer in my rattle can; I had previously just used the delta 3D wpa with the 18mm opening. It worked perfectly when using the 14mm reducer. No sticking or finessing required. The extra depth required to insert it in the 18mm opening was causing too much friction.
I used a 18mm to 14mm reducer in my rattle can; I had previously just used the delta 3D wpa with the 18mm opening. It worked perfectly when using the 14mm reducer. No sticking or finessing required. The extra depth required to insert it in the 18mm opening was causing too much friction.
Vapordeflor
Well-Known Member
Hey Arsenick,
It´s very advisable to take the screen out and, if recoverable, clean it and put it back, or change it for a new one. You will also need to clean the area under that screen, usally a brush is all it takes. Better to do all this process with your vape inverted, this way any herb particulate or cleaning substance will fall into the heater element area, located under the holes.
Repeat this process everytime you deep clean your Mighty bowl.
Last edited:
curubelo
Well-Known Member
Thick Vape
In the Ballpark
Amazing little orange tool, everything is included. Works like a charm and leaves the screen intact to reinstall.
Imagine if it was as easy to clean the bowl as the video suggests 
Thick Vape
In the Ballpark
Haha you got me there. I tried almost everything including DC Cleaner. And while I can get the bowl less dirty I never got it really clean again.Imagine if it was as easy to clean the bowl as the video suggests
grogazola
Well-Known Member
Does anyone have experience with this wpa from PotV?
ca.planetofthevapes.com
Is this the Delta 3D Studios Mighty WPA v3? If so, I’d love to ordered it from PotV Canada and avoid any customs etc!
Mighty & Crafty Water Pipe Adapter (WPA)
The Mighty/Crafty Water Pipe Adapter is easy to use with bubblers/water pipes. ✅ Shop now and get free shipping and a 100% satisfaction guarantee.
Is this the Delta 3D Studios Mighty WPA v3? If so, I’d love to ordered it from PotV Canada and avoid any customs etc!
I got it cleaned up real nice once, but I don’t even remember what I did. Maybe Simple Green. Seems like I also had it on max temp with distilled water swabs trying to “shock” or “deglaze” the burnt on oils off the aluminum. It took a lot more effort than it took to dirty up the bowl again lol - I used capsules at first to mitigate the issue but I prefer the vapor without them.