Herborizer corner
- Thread starter marcuss
- Start date
Vape Soda
Sparkling !
There must be one headless allen screw in the upper part of the Ti element that holds it on the heating rod. If you take of the glass sleeve you should see it. Did you get that small Allen key with your heater?
Razshiro
Well-Known Member
Hippie
Well-Known Member
There's a good pic of the screws here
I think mine came set at 7mm altho the manual says 5-6mm and some say they prefer the tip of the heater protruding out as far as 11mm
That Sherlock stand comes very handy too.
I tend to use it for that first fresh grind tasty bowl microdose.
It can get a little bit harsh sometimes, after that first hit, everything is heat soaked and second hit can get drier, less tasty, but still thick and potent.
A small ash catcher no water, or a dropdown make a “tangible”difference in that.
View attachment 3243
“tangible” Tangie
View attachment 3242
I have Sour Tangie.
Editing a video of a Sour Tangie bowl, with a dropdown and the Sherlock stand...
View attachment 3244Videos are supposed to be 4K 60fps available. Still processing.
First video is at 696F.
A tad too high, even for a fresh bowl with “dropped heater” a la “Zancru”.
Sherlock has no restriction, so your draw needs to be slower than normal to not overpower the heater and avoid hot spots.
Still big flavorful clouds, almost tolerable
Second video is the U jointed Fred the Chicken carb system a la Zancru too.
This time temperature is at a way more comfortable 666F.
And Freddie helps to carb that perfect hit.
Dracarys!!!!
Stay vaped!
Mantente de la mente!!!
p.s: for people wondering what’s a “dropped heater a la Zancru”, use your Allen wrench and slowly counter/clockwise (one way is the correct I believe, the other adds friction) drop down that Ti heater rod.
Start like by 5mm drop down, lower temperatures between 606-636F and go to town.
Warning, remember to lower the dose of material, go microdosing for better results and avoid the heater too close to the herb.
View attachment 3245
My Ti heating rod protrudes 11mm from the tip of the glass injector.
You can clearly see where it used to sit, at that blue line, and the screw mark.
To reach same results with less weed now, I dropped temperatures from above the 700F, now I range between 666F and 696F.
Depends on the mood.
I think mine came set at 7mm altho the manual says 5-6mm and some say they prefer the tip of the heater protruding out as far as 11mm
Gomaruana
Well-Known Member
Hi guys, just got my Herborizer TI for about a week.
What a machine! My previous favorite vape was the e-nano, this thing is the e-nano on steroids.
I think I'll need bigger glass than my bubblers. Would love to see some video/photos of the TI with different glass setups. Carb hole might be a nice addition.
Are there any other must have accessories to get the most fun out of the TI? I didn't buy the glass stand yet because of the comments around it getting stuck. I'm still looking for a solution there.
What a machine! My previous favorite vape was the e-nano, this thing is the e-nano on steroids.
I think I'll need bigger glass than my bubblers. Would love to see some video/photos of the TI with different glass setups. Carb hole might be a nice addition.
Are there any other must have accessories to get the most fun out of the TI? I didn't buy the glass stand yet because of the comments around it getting stuck. I'm still looking for a solution there.
Vapordeflor
Well-Known Member
Hey @Gomaruana !
Well, in my opinion you must get a stand, is equally probable that your herbo will get stuck on the bowl and I can´t think of a safer solution than the Herbo stand.
That said, you might consider getting a double joint adapter and use one of the slots as a carb or directly buy a carb adapter.
Here I leave a little video with my DigiTi Herbo at 343C and some tasty Purple punch with my current Blaze piece:
Enjoy!
Well, in my opinion you must get a stand, is equally probable that your herbo will get stuck on the bowl and I can´t think of a safer solution than the Herbo stand.
That said, you might consider getting a double joint adapter and use one of the slots as a carb or directly buy a carb adapter.
Here I leave a little video with my DigiTi Herbo at 343C and some tasty Purple punch with my current Blaze piece:
Enjoy!
Last edited:
3migo
Is this a...what day is this?
The stand seems like a "must have" accessory to me. I don't know what else you'd do with the injector in between hits/sessions. The injector can get slightly snug inside the stand, but I just put my fingers on the metal base, lightly twist the injector, lift up, and that easily frees it from the stand without issue.
Shadooz
Well-Known Member
"A" stand,... a ceramic mug, bowl can be as good or even better if u find a good form factor (no glass friction, less heat absorption)
Carb hole will have no use. Pulling the heater out will be better and cool the bowl too, if u go for more than 1 hit.
Putting double joint will add "air leak" risk, if u go with cheaper glass....
Vapordeflor
Well-Known Member
Hey @Shadooz
Its curious that you state carb hole will have no use, its an essential part of my hit routine, I milk my piece, then i free the clogged joint to clear the vapor and to finish I lift the vape from the piece (all while inhaling) and place it in the stand. Being able to clear the piece prior to lift the vape gives me just enough time to milk the most without running out of breath, big hits for me
. If you try to clear the piece through the bowl with the herb by just lifting the vape it wont be so instantaneous and I find it more confortable to lift just the vape than the combo bowl+ vape from the bowl handle.
Also it can be very useful to clear your piece without having to lift the vape, I dont do this because I want to keep the glass inyector as clean as possible but I see people doing it and I can understand its more confortable to do so.
Regarding the risk of air leaks, I hear you, I have bought some bad adapters in the past but I think that its worth it to buy some bad ones, in my experience you will get the good ones if not the first the second try, all the adapters I use are air tight.
Edit2: Regarding the stand I will prefer any female glass joint with good stable feet over a mug but thats my way to use the Herbo, I place the vape in the stand while exhaling and it will be so easy to break it leaving it on a mug or a ceramic dish.
Enjoy your Herbos!
Its curious that you state carb hole will have no use, its an essential part of my hit routine, I milk my piece, then i free the clogged joint to clear the vapor and to finish I lift the vape from the piece (all while inhaling) and place it in the stand. Being able to clear the piece prior to lift the vape gives me just enough time to milk the most without running out of breath, big hits for me
. If you try to clear the piece through the bowl with the herb by just lifting the vape it wont be so instantaneous and I find it more confortable to lift just the vape than the combo bowl+ vape from the bowl handle.Also it can be very useful to clear your piece without having to lift the vape, I dont do this because I want to keep the glass inyector as clean as possible but I see people doing it and I can understand its more confortable to do so.
Regarding the risk of air leaks, I hear you, I have bought some bad adapters in the past but I think that its worth it to buy some bad ones, in my experience you will get the good ones if not the first the second try, all the adapters I use are air tight.
Edit2: Regarding the stand I will prefer any female glass joint with good stable feet over a mug but thats my way to use the Herbo, I place the vape in the stand while exhaling and it will be so easy to break it leaving it on a mug or a ceramic dish.
Enjoy your Herbos!
Last edited:
Shadooz
Well-Known Member
If u can't clear with a heater pull off, it's mean u put too much for a 1 hit.Being able to clear the piece prior to lift the vape gives me just enough time to milk the most without running out of breath, big hits for me
So if u just go for a 2 or 3 hit, what's not milked first will be in the next. And cooling the bowl will be a taste savor for the second one.
Now i know my dosage for 1 hit or 2, and i no more go till 3 with the herbo. Only tasty rips now...
Those who lift the bowl after lifting the heater try to go too far too (*cough*
).And people combo lifting both in the same time ? Never seen that, even more useless, not pratical, no bowl cooling...
I usually try to lift the bowl with the heater still on top. It could be a bit of a practice because the heater could tip over, so you have to sort of do a counter balancing act to prevent that and you have to be carefull. You best practice a bit with the heater still cold. Also you need the stand. The stand is a must have accessoire. I am actually surprised it does not come with the vaporizer kits.
Vapordeflor
Well-Known Member
If u can't clear with a heater pull off, it's mean u put too much for a 1 hit.
Those who lift the bowl after lifting the heater try to go too far too (*cough*
I guess what is "too far" for you it´s just perfect for me and other people, I have tested many ways to hit the Herbo since I got it on december 2019 and I just love those milky dense hits... I don´t mind coughing also.
So in my experience there is nothing as "too much" or "too far" if you like it that way! that´s the beauty of life, each to their own
!Just lifting the heater is not really working. It definately does not give you that shoot right up the throat hit experience.
What you can do is buy an extra glass part with 2 18mm connection. One part is for your bowl. The other 18mm hole is for a glass plug. So you can just lift the plug and that becomes the carb hole. Thats how Jerry the vape jesus does it. I think you might have to wear sandals and stuff too.
Something like this:
What you can do is buy an extra glass part with 2 18mm connection. One part is for your bowl. The other 18mm hole is for a glass plug. So you can just lift the plug and that becomes the carb hole. Thats how Jerry the vape jesus does it. I think you might have to wear sandals and stuff too.
Something like this:
Shadooz
Well-Known Member
It definetly does the work, and really well.
Just not visulay the best for "cloud porn" spitting out everything...
You don't even succeed to get cloud at 5 with your 7 days old TI... so yes for u, it may not work...
Go back to combustion for deep throat fuck..
i hear the gargling noises
Last edited:
Shadooz
Well-Known Member
Absolutly not,... if so the bowl won't cooled down, and even worse if u pull everything out, u create blow back...
if you want it to look dirty, go on, and make your dirty porn
The bowl will cool down because after the hit you put the heater back in the stand. It is a ritual.
Put heater on bowl. start hitting that bong. If you got enough vape built up you just lift bowl a bit (You only need to lift it like an inch or 1,5 inch or something) that gives you already plenty of air flow) so you can clear the bong easy. Put bowl back and put heater on the stand.
But if you want to do it different that's fine if that work for you. If you use a small bubbler or sherlock you probably dont even need to lift anything, so that might be a bit different from a bong hit, although i still prefer to lift it anyway, because then you get just a little extra.
Put heater on bowl. start hitting that bong. If you got enough vape built up you just lift bowl a bit (You only need to lift it like an inch or 1,5 inch or something) that gives you already plenty of air flow) so you can clear the bong easy. Put bowl back and put heater on the stand.
But if you want to do it different that's fine if that work for you. If you use a small bubbler or sherlock you probably dont even need to lift anything, so that might be a bit different from a bong hit, although i still prefer to lift it anyway, because then you get just a little extra.
Last edited:
Really torn between the analog and digital Ti versions. The state of the art appeals to me just as well as the tried and true. Is chasing performance with the latest and greatest worth the potential problems inherent to a more complex system? Or does it make more sense to stick with the analog, which is a simpler system and therefore less prone to potential malfunctions?
Will anyone who has used the two systems chime in with a comparison? I have read through this thread but I'm afraid my appetite for comparison has not been satiated.
I must say the promise of more precise control with the DigiTi is VERY appealing to me. But how much more precision are we talking about here? What are the real benefits the DigiTi holds over the analog classic?
**I have a Verdamper as my other desktop vape, and I must say the robust feel and quality old world European craftsmanship really speaks to me. Performance and reliability of the Verdamper are very high, but I'd really like something a bit more compact, the ability to use multiple glass configurations, high performance and precise control over temperature; all without sacrificing build quality and reliability.
Any thoughts?
Will anyone who has used the two systems chime in with a comparison? I have read through this thread but I'm afraid my appetite for comparison has not been satiated.
I must say the promise of more precise control with the DigiTi is VERY appealing to me. But how much more precision are we talking about here? What are the real benefits the DigiTi holds over the analog classic?
**I have a Verdamper as my other desktop vape, and I must say the robust feel and quality old world European craftsmanship really speaks to me. Performance and reliability of the Verdamper are very high, but I'd really like something a bit more compact, the ability to use multiple glass configurations, high performance and precise control over temperature; all without sacrificing build quality and reliability.
Any thoughts?
vaping herbs
Well-Known Member
Hello people,
I am thinking of buying a new desktop vaporizer.
Which of the two models would you buy and why?
Herborizer Ti System 14,5
herborizer.com
Herborizer Ti System 18,8
herborizer.com
I am thinking of buying a new desktop vaporizer.
Which of the two models would you buy and why?
Herborizer Ti System 14,5
Système Ti 14.5 - Herborizer
Système Ti combo vaporisateur/enail (option) équipé d'un variateur de température, pour un contrôle optimal de la vaporisationAdaptable sur tous les bongs équipés de joints 14.5mm
Herborizer Ti System 18,8
Système Ti 18.8 - Herborizer
Système Ti combo vaporisateur/enail (option) équipé d'un variateur de température, pour un contrôle optimal de la vaporisation Adaptable sur tout les corps Herborizer et tout les bongs équipés de joints 18.8mm
Shadooz
Well-Known Member
When the digiti will get back... cause for now it's only the analog available, and only a few left...
The digiti is a must if u want to keep it on, temp regulation.
The TI work really well but i never let it on... i always go from cold and use a timer for gettin my perfect temp.
So if u'r bad at cooking, wait a digiti
One people here said they will be back in may...
They are the same, just the bubbler size u want.Hello people,
I am thinking of buying a new desktop vaporizer.
Which of the two models would you buy and why?
Herborizer Ti System 14,5
Système Ti 14.5 - Herborizer
Système Ti combo vaporisateur/enail (option) équipé d'un variateur de température, pour un contrôle optimal de la vaporisationAdaptable sur tous les bongs équipés de joints 14.5mm
Herborizer Ti System 18,8
Système Ti 18.8 - Herborizer
Système Ti combo vaporisateur/enail (option) équipé d'un variateur de température, pour un contrôle optimal de la vaporisation Adaptable sur tout les corps Herborizer et tout les bongs équipés de joints 18.8mm
I get two 18mm bowl at first to go with my mobius but move to a smaller 14mm so i bought two 14mm bowl also after
18 mm is only good if u need a lot of cooling, and so big glass
Well the digTi has numbers on it but nobody seems to know what the numbers mean because it is neither celsius, fahrenheit or kelvin. So i am not really sure if that adds any value to the digital experience. If you use the analogue ti you just have to put it somewhere in between 4 and 6.
It is all a matter of try what you like. with these herborizers you just have to trust your gut feeling rather than worry about the temperatures, because both analogue and digital do not show the temperatures, they just show a bunch of numbers that have nothing to do with any temperature scale.
It is all a matter of try what you like. with these herborizers you just have to trust your gut feeling rather than worry about the temperatures, because both analogue and digital do not show the temperatures, they just show a bunch of numbers that have nothing to do with any temperature scale.
Last edited: