ataxian
PALE BLUE DOT
Good Luck with your decision.Ugh this is such a hard decision
The NANO is fast so it can be a daily driver if need be.
The VRIP is great for FLAVOR however sessions are a bit longer!
Good Luck with your decision.Ugh this is such a hard decision
maybe I am doing something wrong, I have tried again tonight and I am still not getting hits as good as my PD.
Perhaps I should try attaching the silicone tubing to one of my nano stems, am I right in thinking this improves the seal between the vaporizer and the stem?
Also do people usually put the hole bit of tubing they are sent on to one stem or cut it into sections and attach small bits to different stems?
I am sure it must be my usage technique I can't believe the unit doesn't give as good highs as the PD.
maybe I am doing something wrong, I have tried again tonight and I am still not getting hits as good as my PD.
Perhaps I should try attaching the silicone tubing to one of my nano stems, am I right in thinking this improves the seal between the vaporizer and the stem?
Also do people usually put the hole bit of tubing they are sent on to one stem or cut it into sections and attach small bits to different stems?
I am sure it must be my usage technique I can't believe the unit doesn't give as good highs as the PD.
Hi all, I just tried again with the nano, I increased my draw speed and added more bud.
Then I wacked the dial to maximum, waited about ten minutes and vaped. Wow this thing is a monster I must say.
Just wondering is there a recommended time for leaving the dial at maximum? I have found my converter gets quite hot.
I now feel quite calm and heavy with the PD I usually feel alive and really energetic.
I don't leave the dial at max all the time and in fact turn it off when not in use.
Hi all,
well I took my nano for its first test drive last night, and unfortunately I was a little disappointed.
firstly I had the issue with the all glass stem of bits of herb ending up in my mouth, so I guess I will stick to using my other stem with the metal screen in, and also install an extra screen in the all glass one, though I have a feeling this will be fiddly, and I would appreciate some guidance on this.
I also had the issue when I had filled the stem that most of the herb inside it dropped out into the unit so I had to turn it over and tap the bottom to get it to come out.
Having said that I did enjoy the bit of flavor I got to taste, but I suspect I didn't get to appreciate the units full potential.
Any tips on getting my herb to stay in place would be appreciated, I did try using the epic to give it a prod but that didn't seem to help.
most of my material is ground up, but its not what you would call really finely ground, I do have a bit that isn't ground yet, the problem I have is allot of it is mixed in with leaves and bits of stem so grinding is kind of needed, anyway I have a bit ground up that I can normally use in my PD fine so not quite sure what the trick is to putting it through my nano.
Any help and advice would be appreciated I did like the very easy draw from the unit, and it was really nice holding the warm glass stem. I tried inserting the stem into the unit with the unit tilted at an angle, took a few draws and then stood the unit up right on the desk with stem inserted. This is basically the same technique I use when first drawing from my pd and mostly herb seems to stay in place.
as to what my bud looks like I can't say as I am blind, but I do know that I don't get any smell of burning at maximum temperature, which I am sure I would as often stuff still falls out of my stem and ends up on the top of the heater where the stem rests.
1) It does sound like the adapter is the problem. It should not be getting hot, and it does sound like your heater is not getting hot enough.Hi,
regarding my converter its quite possible it might not be very good, to be honest I was dubious about buying it from ebay as it only cost about £3.
I actually looked at ones that cost about £25 on amazon, but when I asked Andy for advice because I wasn't sure if the specifications were OK for the nano he sent me the link to the ebay one and advised me to get it.
as to what my bud looks like I can't say as I am blind, but I do know that I don't get any smell of burning at maximum temperature, which I am sure I would as often stuff still falls out of my stem and ends up on the top of the heater where the stem rests.
I know I want to upgrade from an Extreme Q to a GonG wooden log vape for my upcoming Leviathan Big Mona order (I love water pathways/bubblers!), but I can't decide between an Underdog or an E-Nano vape (on wait list for the HI Log for six more months).
Are the Underdog and E-Nano similar? Are there any other alternatives I should check out? I'm putting a premium on GonG-to-Bubbler pathway, minimal pathway before hitting the bubbler, *fast* vapor production (from off to vapor clouds in <= 2/3 minutes), really nice thick cloud vapor production, and flavor.
I ordered one 8/12/13 (last Monday). On 8/17/13 (Saturday) I ordered another one along with some accessories and was told they would both ship on 8/21(Wednesday). The two cherry Nanos are coming with the all glass stem that I will probably add a ss screen to. I ordered the gongs with the ss screen not the all glass. Cant wait to see this thing!