joerghustle
Well-Known Member
any suggestions for improving the heat up time from a apollo2?
Dynavap VapCap
- Thread starter Fenton Mewley
- Start date
stark1
Lonesome Planet
If you are a flavor hound like I am, you actually want a slow hand with the heat on the mag.
joerghustle
Well-Known Member
i use my dynavap only in waterpipes
with a lighter i extract in 1 hit heating near the "diggerouter"
Planck
believes in Dog
Well George likes hot cheese and this is hot and cheesy so perhaps mission accomplished.
I think is has all the appeal of a blow up doll.
If the trademark was bigger I'd be all over it.
TommyDee
Vaporitor
I have to say this in defense of the Apollo 2... the innards are most likely perfectly good. This thing has had a long hard look so it can't be all bad. Just a poor choice of aesthetics.
And I definitely see an aftermarket box upgrade for the Apollo 2. Maybe also include a way to save the face-plate as an option.
BabyFacedFinster
Anything worth doing, is worth overdoing.
I think is has all the appeal of a blow up doll.
Actually
I agree. During the video the guy showed the care put into designing the control board and I believe George would be stringent on the build quality.
Like taking your sister to the junior prom.
stark1
Lonesome Planet
Well George likes hot cheese and this is hot and cheesy so perhaps mission accomplished.
I think is has all the appeal of a blow up doll.
If the trademark was bigger I'd be all over it.
How do you know Geo likes hot cheese, or are you just cutting the Cheese?
(Blow up doll can be useful, in a commuter lane)
Any sightings in the wild of the M-20?
Last edited:
Planck
believes in Dog
It's not a secret that he imbibes hot cheese with great relish.
ETA;
Me too, it's duct tape.
Planck
believes in Dog
That is cheese made from toe jam?It takes a good cheese to make a top VapCap?
rnartian
Earthling flora is... fascinating.
Yeah, the Dynatec is basically an Apollo 2 with a custom (branded) faceplate, as shown here:
^ see the "Apollo 2" logo at the bottom left.
if there are any differences in efficiency or build (which I doubt), Lucid nor Dyna themselves have reported anything at this time.
I'm guessing whoever does graphics at Dynavap designed the faceplate and Lucid Customs does the heater in the same style as their own.
[keyword; 5-point safety torx] ...or reboxing. They really want to keep us out 
Now I want to see 
BabyFacedFinster
Anything worth doing, is worth overdoing.
You're gonna do that while driving?
Interesting on the use of torx fittings with the Dynatec.
stark1
Lonesome Planet
Wow. Thanks, @Vaporooni! 
For sharing.
Did ya have to use special torxs (hollow, for the center pin)
—Quite a bit of space 2-spare; bet it can be
Made EDC small (-er).
Any air/heat vents?
Close to 2 bills for it?
For sharing.Did ya have to use special torxs (hollow, for the center pin)
—Quite a bit of space 2-spare; bet it can be
Made EDC small (-er).
Any air/heat vents?
Close to 2 bills for it?
Last edited:
Yes you will need a Torx set for this one like @TommyDee KAIFNT set, If your not worried about the warranty. Plenty of air vents now.Wow. Thanks, @Vaporooni!
Did ya have to use special torxs (hollow, for the center pin)
—Quite a bit of space 2-spare; bet it can be
Made EDC small (-er).
Any air/heat vents?
Close to 2 bills for it?
Last edited:
StringTheorista
Well-Known Member
stark1
Lonesome Planet
Indeed! Like your coiled diamondbacks.
What’s that boxy thing in the back with all the wires.
Last edited:
