Kalessin

Well-Known Member
1) Can the condenser be pushed until there is no airflow from the carb or do I need to cover the carb again?
2) Do most of you feel there is enough airflow with a Ti tip and closed carb so I can do comfortable mouthpulls? It should be tight enough to make a normal draw really hard but airy enough so I can mouthpull....
I have no use for the carb. First I plugged it, but then I realized I could slide one of the internal o-rings that support the condenser past the carb and it forms a perfect seal. Mouthpulls are not my technique, but they've always worked fine when I've tried them.
 

The Stranger

Account Closed
I have no use for the carb. First I plugged it, but then I realized I could slide one of the internal o-rings that support the condenser past the carb and it forms a perfect seal. Mouthpulls are not my technique, but they've always worked fine when I've tried them.
Oh this is exciting to know! You can cover the carb and it'll essentially have to be puffed like a joint?
 

Derrrpp

For the world is hollow and I have touched the sky
Thanks for the pics @Derrrpp. Man I really do like the look of that crown, decisions decisions!

By the way, how did you get one with a crown? I thought the option only appears a few days ago when he switched to the new site.
No problem man, it's my pleasure! I love taking pictures of my Woody! :brow: :lol:

I got mine by just messaging George and asking him if he could add a crown on the mouthpiece end. And I paid the extra $5.

How are the crowns attached? Do they used glue? And does that crowned tip as mouthpiece get hot?
I'm not sure how he attaches the crown. I imagine it's just a friction fit with no glue, but I could easily be wrong about that. You know what they say about assuming, haha. And the mouthpiece crown doesn't get hot at all, the only part that gets hot is the titanium tip.
 
Last edited:

Oogendoogan

Well-Known Member
So I corresponded with Matt, George's employee at Dynavap yesterday. He is a great guy and dealing with him was just like dealing with George. Super easy, quick responses, super helpful. He made sure that all of my different orders and notes from the old site were translated corectly. I had quite a confusing order lol but today I got emails from George saying my short double crowned Blackwood body and malee Burl mouth piece have shipped! Also my hemp fiber and my VapCap OG :) Matt asked if I wanted to wait a little longer and get my VonG body and DynastashER with my Woody and OG all at once. I told him to send the Woody/OG and I would wait because it is so hard watching all of your beautiful vapes not having my own. Couldn't be happier that my vapes are coming and also couldn't be happier with the company they are coming from. Great to watch a good company grow and get their amazing product out. Can't wait to get my vapcaps and post some pics of my own.
Cheers,
Stay vaped.
 

We5d

Well-Known Member
Beautiful pics every time someone posts their woodies (this could be interpreted wrong if on another forum, haha)

Loving my Ti Cocobolo but VAS is strong

Will be saving up for a Ti Burly double crown and hoping I can special request an XL titanium mouthpiece.

Drooling at the thought already...
 

bobcool09

Well-Known Member
I've made a case for my Ti Woody + rubber mouthpiece. It's a 16x125mm test tube that I bought from the local surplus store for $0.65, and a matching rubber stopper($0.10) that I cut to the correct size. It holds the VapCap in securely, with no movement whatsoever if I shake it. It also fits my Ti + XL condenser and wood mouthpiece, but if you want to do both XL condenser + wood mouthpiece + rubber mouthpiece, you'll have to get a 16x150mm test tube.
Although it isn't as indestructible as the regular cases, it does look pretty nice in my opinion. Sorry about the quality of the pictures, my phone doesn't have the best camera.
I also found out that the regular tube fits perfectly inside of an empty M&M minis tube (click for picture, it showed up big and ugly when pasted directly). The only use I can think of for this is if you want to be really discreet.
hwuEaAQ.jpg
bIHArHx.jpg
 

b0

Cloudy...
So bad news my friends, my Ti Glassy died today :cry:

I was outside hiking, using my Ti Glassy and it sudenly fell in the floor. A little corner of the glass broke but it was enough to make it unusable.

So now I have decided to order an omnivap! :nod:

That way I will have an unbreakable Vapcap to take with me everywhere and with the extra glass body that comes with the Omnivap and the parts of the Glassy I can make another Ti Glassy. Love this "lego" system :bowdown:

And here come my doubt, should I buy a Dynastash? I like the design and it's really cool, but I dont know if the Omnivap fits. Also I don't like that the herb is gonna be in contact with the wood, anyone knows if it's posible to use a glass (or plastic if not, but glass would be amazing) sleeve like in the Jyarz? That would be awesome!
 

b0

Cloudy...
Omnivap fits in dynastash, also you can put a short wood body on them, think it looks great!
Cheers

I really love how the wood looks, but it changes the flavor and I'm a bit OCD and like my vapes as clean as posible so I try to avoid wood because I can't ISO soak it.

But nice to know that the omnivap fits! :tup:
 
Last edited:

CharmCityVapeGuy

Known to some and enigma to others
can anyone tell me how to install the extended mouthpiece?

do i just remove the finned cap, push out the metal stem, and insert the extended stem and mouthpiece and put the finned cap back on?

has anyone found good storage for the vapcap and extended moutHpiece? I notice its too tall for the doob tube.
Yes, that is exactly how you install the XL mp. It's super easy.
 

StormyPinkness

Rhymenocerous ʕ•ᴥ•ʔ
Does anyone else have trouble getting the ss tube back in a glass body with the o-rings in the right spot? The lower o-ring that sits next to the carb hole (or should) just refuses to slide down. I tried using a paperclip to push it but it got really difficult and I thought I was going to pierce right through it. I've just been leaving it pretty much next to the o-ring by the mp where it stops sliding down. Doesn't seem like it's negatively affected it though. Also this was after a fresh iso soak so it was totally clean.
 
StormyPinkness,

b0

Cloudy...
Does anyone else have trouble getting the ss tube back in a glass body with the o-rings in the right spot? The lower o-ring that sits next to the carb hole (or should) just refuses to slide down. I tried using a paperclip to push it but it got really difficult and I thought I was going to pierce right through it. I've just been leaving it pretty much next to the o-ring by the mp where it stops sliding down. Doesn't seem like it's negatively affected it though. Also this was after a fresh iso soak so it was totally clean.

It never h appened with mine :shrug:
 

Kalessin

Well-Known Member
Does anyone else have trouble getting the ss tube back in a glass body with the o-rings in the right spot? The lower o-ring that sits next to the carb hole (or should) just refuses to slide down. I tried using a paperclip to push it but it got really difficult and I thought I was going to pierce right through it. I've just been leaving it pretty much next to the o-ring by the mp where it stops sliding down. Doesn't seem like it's negatively affected it though. Also this was after a fresh iso soak so it was totally clean.
Try lubing the oring?
 

Squiby

Well-Known Member
Does anyone else have trouble getting the ss tube back in a glass body with the o-rings in the right spot? The lower o-ring that sits next to the carb hole (or should) just refuses to slide down. I tried using a paperclip to push it but it got really difficult and I thought I was going to pierce right through it. I've just been leaving it pretty much next to the o-ring by the mp where it stops sliding down. Doesn't seem like it's negatively affected it though. Also this was after a fresh iso soak so it was totally clean.
You might have better luck by lubricating the orings with a bit of spit before sliding the condenser into the sleeve.
 

Oogendoogan

Well-Known Member
I really love how the wood looks, but it changes the flavor and I'm a bit OCD and like my vapes as clean as posible so I try to avoid wood because I can't ISO soak it.

But nice to know that the omnivap fits! :tup:
Pretty posative that the wood models have a completely stainless steel isolated air path, meaning the vapor never touches the wood, not affecting the taste and never needing to be cleaned, just iso soak the stainless steel path and the titanium extraction tip and your good. and with the omni the wood would just go outside the vapor path, just would look pretty, tasting and working the same as with a titanium body.
 

b0

Cloudy...
Pretty posative that the wood models have a completely stainless steel isolated air path, meaning the vapor never touches the wood, not affecting the taste and never needing to be cleaned, just iso soak the stainless steel path and the titanium extraction tip and your good. and with the omni the wood would just go outside the vapor path, just would look pretty, tasting and working the same as with a titanium body.

You sure the inside of the wood is ss? If it's a simple sleeve like the Glassy, the wood is in the airparth.

It's gonna be an option to have a woodie omnivap? Didn't know that :o
 

Kalessin

Well-Known Member
You sure the inside of the wood is ss? If it's a simple sleeve like the Glassy, the wood is in the airparth.

It's gonna be an option to have a woodie omnivap? Didn't know that :o
There IS a SS condenser tube inside the ti woody, but it is not completely sealed off. I don't think much vapor touches the wood, but if you don't keep the ti tip pretty clean oil will build up in it and drip down onto the wood.
 

Spocks_Katra

Well-Known Member
been using my vapcap for a few days now,

Flavor is great! the first heat up is pure flavor!
extraction is among the best i have experienced
Size is a huge bonus. I can carry my vapcap, a doobtube of herb and a lighter easily in my pocket, with room to spare

Craftmanship 11/10
 

Oogendoogan

Well-Known Member
There IS a SS condenser tube inside the ti woody, but it is not completely sealed off. I don't think much vapor touches the wood, but if you don't keep the ti tip pretty clean oil will build up in it and drip down onto the wood.
Thanks I don't have mine yet so I'm not sure but I am pretty sure George has said that wood shouldn't effect the taste, and idk about with the omni it may be even cleaner?
 
Oogendoogan,

Andreaerdna

If God is the answer, then the question is wrong
Got my order yesterday, a lot of spares and parts.
xl VapCap (ti glass with Wood mouthpiece and xl condenser) is my favorite length, both for spinning while heating or for the extra chilling vapor path.

Now my hope/waiting is for a condenser adequate to the omnivap, in order to extend it while keeping the possibility to adapte draw resistance.
 

scottyc22

Member
After deciding on the Boundless CF over a Ti Woody (ease of use, stealth), I've decided to order an OG as well to experience both worlds. But after reading everywhere that the OG looks like a crack pipe when not cleaned regularly, that's an issue for my current situation. I can't afford any Ti models alongside my CF. Is it possible that I could cover the outer glass with silicone or some other material that 1. Would protect the glass from damage 2. Wouldn't allow people to see the resin from outside? Aluminum foil tape? Would that change any functionality? I would cut a hole to make sure the carb hole wasn't permanently closed.
 

Andreaerdna

If God is the answer, then the question is wrong
After deciding on the Boundless CF over a Ti Woody (ease of use, stealth), I've decided to order an OG as well to experience both worlds. But after reading everywhere that the OG looks like a crack pipe when not cleaned regularly, that's an issue for my current situation. I can't afford any Ti models alongside my CF. Is it possible that I could cover the outer glass with silicone or some other material that 1. Would protect the glass from damage 2. Wouldn't allow people to see the resin from outside? Aluminum foil tape? Would that change any functionality? I would cut a hole to make sure the carb hole wasn't permanently closed.

Have similar concern:
If you add the small mouth piece with XL condenser (25 usd) there will be very little oil accumulating on the body walls. Condenser get almost everything.
 
Top Bottom