just cause I said its not that hard doesn't mean I got it right add filming to the mix and that its still a work in progress. but at least its worth a laugh lol
$62... and that handle again looks worthy of a sub $10 product. Super disappointed. CH needs to ditch things they don't do well (wood) and stick to what they are good at.
Taking a hard pass for now.
Okay so I really want to convert my VROD into a ball setup, my only question is does the screen baller work with the VROD? Or is it a separate head entirely? I haven't really been able to figure that one out.
Second, what is everyone's favorite setup with the BROD? Should I got for screen baller? OG baller? Etc.
You're going to need either one of the Baller head assemblies along with the Vrod Head Top. I'd honestly email their support and see if they can let you only order the Vrod Head Top along with the Baller to save some cash.Okay so I really want to convert my VROD into a ball setup, my only question is does the screen baller work with the VROD? Or is it a separate head entirely? I haven't really been able to figure that one out.
Second, what is everyone's favorite setup with the BROD? Should I got for screen baller? OG baller? Etc.
Just trying to figure out what I need to order to get the best experience! Since I have the Halo by iDB now I want my VROD to just be a pure facemelter haha
It all depends on the 5 pin connectors setup. I’d be really careful. Check at CH for their pin connections and check compatibility with that new coil pin connections. If + or - are swapped, you’ll be SOL , but if you’re good with electronics and soldering, it’ll be a piece of cake the swap.Might be bit of a long shot but can anyone confirm that the "silver plug" version of this flat coil will work with the old newvape PID pictured below. Just got my T-bucket today but ordered a new flat coil that doesn't work with my controller so had to order the one above. Also the above coil usually comes with this setup and controller that looks like my older newvape controller. So it should be ok right? Thanks
Current controller:
After owning the V-rod for over a year, I bought the weed eater just to see how it was to use. What a mistake; it was awful. It feels like there is close to zero heat retention with that thing. I wound up having to sip the vape like tea. Which is contrary to the entire idea of the FP in the first place.I agree. I kind of feel like the Baller has the potential to replace the WeedEater not the VRod.
After owning the V-rod for over a year, I bought the weed eater just to see how it was to use. What a mistake; it was awful. It feels like there is close to zero heat retention with that thing. I wound up having to sip the vape like tea. Which is contrary to the entire idea of the FP in the first place.
I recently started using the baller screen setup w/2mm balls and a 2-holed-carb-cap for extra flow lost by the smaller quartz spheres. I really like the setup. It holds more heat than I can suck out of it. Just plows through flower at a consistent temp the whole way through.
In my experience the carb cap is a necessity for the weedeater to get the hits I wanted with my draw speed.After owning the V-rod for over a year, I bought the weed eater just to see how it was to use. What a mistake; it was awful. It feels like there is close to zero heat retention with that thing. I wound up having to sip the vape like tea. Which is contrary to the entire idea of the FP in the first place.
I recently started using the baller screen setup w/2mm balls and a 2-holed-carb-cap for extra flow lost by the smaller quartz spheres. I really like the setup. It holds more heat than I can suck out of it. Just plows through flower at a consistent temp the whole way through.
Curious to hear how snug a fit folks have for their B-rod heater on the Shovel Head. I feel like I have a good deal of wiggle in my set up.
Also feeling that even with what should be an easy drawing MegaGlobe that the draw strength needed is a bit more than I'd like. Any other ideas other than these:
Yeah, I imagine some of this has been addressed before, but oof this is a 792 page thread....
- Switch from 3mm to 4mm balls
- Get a screen for below the flower that is a les tight weave.
first I should say this my not be safe? but I'm something of a risk taker . its vegan and non poisonous ........... how can I go wrong ? recently had a dab, taste was amazing ! and I'm not dead? for now?............. I tasted no strange flavours, saw nothing coming off the dish and noticed no colour change after it was heat soaked. seemed ok? dab of bubble hash was delicious , don't feel anything weird? just my normal high. so I'll probably use it again unless someone tells me ive got 5 minutes to live or something.what solution was it?