The Stray Fox
Separated from the group
Wow that hurts my head to think about. You could do all 4 I believe but for the B-1 you would have to do the screen hack with the WE top nut.
Cannabis Hardware (formerly NewVape) FlowerPot Twax Vaporizer
- Thread starter natural farmer
- Start date
DamnGentleman
Well-Known Member
The B-1 uses its own nut with a groove for the top screen. The Weedeater nut doesn't have that groove but you can still jam a screen in there, it's just a little less elegant. You might also want to consider getting separate coils for B-1 and B-2 as they fit a bit differently. Personally, I think the balled heaters are such an improvement that I see no reason to go back to the OG titanium diffusers.
delta hotel
Well-Known Member
To your edit: Yes. This is what I did and I think I'm sticking with the B-1 for now. I converted a VROD to a B-2, then I bought the nut you mentioned and converted it into a B-1. I can make all of the CH units now except the original weedeater.
someTooL
Well-Known Member
@RustyOldNail thank you for pointing out the 2 hole cap. Totally missed this and have been wanting to try out with the DCup. Any experience with the prior 2 hole?
Severmore
Well-Known Member
Thanks guys! You all are great!
@delta hotel
Won’t the combination of your original VROD diffuser with the B-1 nut make for a functional WeedEater? It does in my head at least
@delta hotel
Won’t the combination of your original VROD diffuser with the B-1 nut make for a functional WeedEater? It does in my head at least
Last edited:
RustyOldNail
SEARCH for the treasure...
I just use the OG ATWO HOLE cap that came with my DCup, I could always plug one hole with tiny silicone plug if desired. Then I got the Universal cap a few weeks ago, with ONE HOLE, now it seems it’s got TWO HOLES. The new one doesn’t SPIN as easily as it has more grooves, so each groove is THINNER. It will work, just have to be more careful when spinning.
delta hotel
Well-Known Member
The top nut for the B-1 is a little different, it uses a screen and not the drilled holes.Thanks guys! You all are great!
@delta hotel
Won’t the combination of your original VROD diffuser with the B-1 nut make for a functional WeedEater? It does in my head at least
Severmore
Well-Known Member
@delta hotel
The drilled holes come from the OG diffuser side of the equation, yeah? Simply remove the screen of the B-1 and mate the two pieces together? I’m probably confused.
Regardless, I’ma buy a B-1 Nut…and yes, this soon after a BF sale. Doh!
The drilled holes come from the OG diffuser side of the equation, yeah? Simply remove the screen of the B-1 and mate the two pieces together? I’m probably confused.
Regardless, I’ma buy a B-1 Nut…and yes, this soon after a BF sale. Doh!
snackmaster
Well-Known Member
I tried my B1 nut on my old 18 hole diffuser and you can attach them just fine without removing the screen.
The Stray Fox
Separated from the group
I’ve got a DCup two hole. It’s got a tooth pick in one of the holes. I liked the one hole universal cap with DCup. The vacuum pressure it creates just feels better. That’s what lead me to block one of the holes on the DCup carb.
I did enjoy my OG VRod 2 hole carb on my VRod.
snackmaster
Well-Known Member
I found another washer from EXTSW that holds the shovelhead pretty well and fits the carb cap spot on the PID stand: EXTSW 3/4" / .755” ID x 1 1/4” x 7/8" long 316 Stainless Shaft Spacer. Works with male posts, not sure about female.
Great find. And carb cap can just go on baller until you start heating it up...
Oh, free shipping right now too...
The Stray Fox
Separated from the group
He’ll yeah. I need this for that Timberhead PID I just won. He did put a heat post on it but there is no place for the ShovelHead.
snackmaster
Well-Known Member
Ooh nice I think I caught a glimpse of that on his IG story the other day and it looked great. I've been playing around with a couple designs for PID stand enhancements I want to run by him to see if they're viable.
SquirrelMaster
Well-Known Member
My BF order arrived yesterday and after a quick clean of all the parts I had my VROD converted to the B2 with a new B1 beside it. The 2 Ed's TNT handles I ordered are stunning! The ergonomics absolutely crush the stock Shovelhead bowl, this is a worthwhile upgrade imo.
I was scratching my head a little when I set the new Auber to 320° and I wasn't getting any vapor, but I quickly remembered they come set to Farenheit not Celsius so I swapped units and set the dial to 320°C/608°F on both Auber's.
After a few minutes of warming up while I checked on my plants (my Slurricane #7 is looking frosty!) I took the plunge. The B1 is ridiculous, I've never seen my Sphere fill up with vapor so quickly. I agree with @delta hotel in response to @ManFlies352 that no carb cap is needed for the B1 and I actually feel like it hurts the performance. I don't have a new universal carb cap but instead a Beracky glass cap and the additional airflow restriction is exactly that, without a noticeable increase in vapor density. The B1 isn't as free flowing as a VapBong for comparison but it's easily the most free flowing of the CH family and just gives you instant vapor.
The B2 is a different kind of beast. I need to open mine up and re-work the rubies because I'm getting a good hot spot on a portion of the bowl. Both my B1 and B2 currently have 3mm rubies installed. It hits harder than the VROD, that's for sure, but compared to the B1 I need to do more side by side testing (which completely crushes me) to see what I think of each. My tolerance has been climbing over the past week and these two are going to destroy it.
I was scratching my head a little when I set the new Auber to 320° and I wasn't getting any vapor, but I quickly remembered they come set to Farenheit not Celsius so I swapped units and set the dial to 320°C/608°F on both Auber's.
After a few minutes of warming up while I checked on my plants (my Slurricane #7 is looking frosty!) I took the plunge. The B1 is ridiculous, I've never seen my Sphere fill up with vapor so quickly. I agree with @delta hotel in response to @ManFlies352 that no carb cap is needed for the B1 and I actually feel like it hurts the performance. I don't have a new universal carb cap but instead a Beracky glass cap and the additional airflow restriction is exactly that, without a noticeable increase in vapor density. The B1 isn't as free flowing as a VapBong for comparison but it's easily the most free flowing of the CH family and just gives you instant vapor.
The B2 is a different kind of beast. I need to open mine up and re-work the rubies because I'm getting a good hot spot on a portion of the bowl. Both my B1 and B2 currently have 3mm rubies installed. It hits harder than the VROD, that's for sure, but compared to the B1 I need to do more side by side testing (which completely crushes me) to see what I think of each. My tolerance has been climbing over the past week and these two are going to destroy it.
Severmore
Well-Known Member
Ed’s handle should not affect this washer/spacer’s ability to function as a stand for the shovelhead, yeah?
David Root
Well-Known Member
Ed's handle replaces the stock one. I ordered two.
delta hotel
Well-Known Member
Exactly! Like I said, an issue I had with some pieces was that I needed to hold it or position it in a way, that I couldn't hold the glass, to then grab the cap off and remove the handle, unless I wanted to do grab the cap and handle with one hand, but I felt like that was risking burning myself. Now I only need to hold the glass and the handle.
I don't have that washer, but I do have Ed's handle, and I can say from the pictures, that no, it wouldn't interfere with it.
snackmaster
Well-Known Member
Can confirm this is correct
thevapist
Well-Known Member
I snagged an Ed's handle and it doesn't fit my 2-3 year old flowerpot bowl thread. Goes in a tiny bit then stops. I compared it to their other handles/tools and it seems to be a different thread? Anyone else seeing this?
It does fit a newer flowerpot bowl I got about a year ago.
It does fit a newer flowerpot bowl I got about a year ago.
710yota
Have you heard about the boom on Mizar 5?
Maybe not the same issue but still a threading issue is mentioned here, might be a ongoing issue and worth contacting CH about.
The Stray Fox
Separated from the group
https://www.cannabishardware.com/blogs/newvape-blog/count-down-timer
I’m hoping for an 18mm bottom nut for injector style glass bowls like used with the Heborizer/TerpTorch.
I’m hoping for an 18mm bottom nut for injector style glass bowls like used with the Heborizer/TerpTorch.
bizwaxzion
Enigmatic Cannabist
I have an 2.5 year old NewVape shovelhead and a CannabisHardware shovelhead from this year. The handles are NOT interchangeable.
David Root
Well-Known Member
I don't think its an "Ongoing issue".
I think I got a goof, and I am a mechanic.
Threads should be at least as long as the bolt thick.
Math says I should have 4.5 threads, I have 2.
3/6" (.1875) Diameter. 24 threads per inch, .041 inches per thread, .1875/.041=4.573 threads.
This is not a big complaint.
How thick is the bowl where the threads are?
Can I ever get a Pan Head Bowl?
I am reading around page 179 where they are developing the bowl. I think its perfect.
Pan Head, Shovel Head, VRod.... I have 3 BMWs in my garage including a 21 R 18 First Edition with 10,000 miles on it I bought this spring.
David
B1 shows up tomorrow.
I think I got a goof, and I am a mechanic.
Threads should be at least as long as the bolt thick.
Math says I should have 4.5 threads, I have 2.
3/6" (.1875) Diameter. 24 threads per inch, .041 inches per thread, .1875/.041=4.573 threads.
This is not a big complaint.
How thick is the bowl where the threads are?
Can I ever get a Pan Head Bowl?
I am reading around page 179 where they are developing the bowl. I think its perfect.
Pan Head, Shovel Head, VRod.... I have 3 BMWs in my garage including a 21 R 18 First Edition with 10,000 miles on it I bought this spring.
David
B1 shows up tomorrow.
snackmaster
Well-Known Member
Check out this CH blog post https://www.cannabishardware.com/blogs/newvape-blog/let-me-handle-this