AVS m22

Oil420FL

Well-Known Member
So long as I get a good install (resistance at or below marked on the container) I get a resistance read and then lock resistance. I will use the escc until performance drops but don’t re-read resistance.

A little resistance drift really doesn’t matter. Both the v1 and v2 work fine with dna. I setup a custom material profile in escribe with the recommended TCR.

The controller tower is also really close at this point so that might be n option as well.

But my v1 paired with a paranormal dna250 and a v2 paired with the 510 cable and a Odin 250c work imo equally as well as the beta control tower.
I seem to recall reading that 510 cables often made DNA units revert to wattage out of TC mode because of resistance changes [or is my memory foggy on this?].
 
Oil420FL,

DankNug

Active Member
I seem to recall reading that 510 cables often made DNA units revert to wattage out of TC mode because of resistance changes [or is my memory foggy on this?].
It does for me, but on my dtv5 on my dna unit. I use the m22 510 cable. It didn't end up lasting long, took them 6 months to replace and it still didn't last long. I didn't think I was super tough with the cable. I ended up getting this for my DTV5 and haven't looked back to a cable since. Maybe it'll help someone who gets annoyed by the cable

small jack stand
 
DankNug,
  • Like
Reactions: Oil420FL

BakedDiogenes

Well-Known Member
Anyone have a good method for removing the stock black mouthpiece tip? Looking to swap it with a different 810 piece.
 
BakedDiogenes,

BakedDiogenes

Well-Known Member
Ohhhh I see. In that case, I'd toss the whole top in ISO until it softens up a bit.
Worked like a charm. Thanks!

Testing the new tip with some Future Ex-Wife rosin I picked up today. 20w on the 6-sec profile. Definitely a much cooler hit, and I may throw some balls in at some point for further cooling.



image hosting

 

Chicken No Name

Dazed and confused
Just hitting some runtz rosin in the M22 using their bubbler.
Due to my own special clip installation tech I get about 5 hits before resistance goes off so I stick with wattage, just pulsing old school. I'm quite good at it now so I still love her, warts and all.

IMG-20221129-152821.jpg
 

SpaceCowboy702

New Member
It might just be my preference. Believe me I want to like the DTv5 more given how cheap replacement cups are. Everything just seems smoother to me on the m22. Part of it might be SiC over white ceramic.

If you want to try, let me know what version of the ESCC you have and I can get the right curve files for you.
I just got an M22 for my Rx gen 3 Dual but I'm so lost on setup since I'm coming from a Sai+. Any chance you could spare a few minutes to help me out??
 

SpaceCowboy702

New Member
Just hitting some runtz rosin in the M22 using their bubbler.
Due to my own special clip installation tech I get about 5 hits before resistance goes off so I stick with wattage, just pulsing old school. I'm quite good at it now so I still love her, warts and all.

IMG-20221129-152821.jpg
I have an Rx Gen3 Dual, may I ask what settings you are using??

What’s the question?
I'm on my lunch break rn is there anyway to make a profile right now without using a PC? I'm so new to this that I don't want to mess up the ESCC I just got it last night. It's a high ohm ESCC btw
 
SpaceCowboy702,

florduh

Well-Known Member
I have an Rx Gen3 Dual, may I ask what settings you are using??


I'm on my lunch break rn is there anyway to make a profile right now without using a PC? I'm so new to this that I don't want to mess up the ESCC I just got it last night. It's a high ohm ESCC btw

Brother, if you're rocking a high ohm you'll want to use Wattage Curves on Arctic Fox. I'm pretty sure I posted a link to the curves somewhere on this thread. If not, I can find them later tonight.

You will need to connect your mod to a PC and install Arctic Fox before you can load any custom curves.
 

SpaceCowboy702

New Member
Brother, if you're rocking a high ohm you'll want to use Wattage Curves on Arctic Fox. I'm pretty sure I posted a link to the curves somewhere on this thread. If not, I can find them later tonight.

You will need to connect your mod to a PC and install Arctic Fox before you can load any custom curves.
I already have AF my apologies I should have explained myself better. I actually downloaded the link you supplied for someone else prior but since I'm at work away from a PC I wanted to see if I could erase an existing profile and just input the settings from edit mode on the mod. I guess I should have brought my Sai+ with me as well lol now I'll have to just look at this rosin and hope we're almost done with this job.
 
SpaceCowboy702,
Top Bottom