When you set it on the station does it look perfectly upright? If you turn your VM one position, does it sit any differently? With one of mine, if I seat it carefully and in the same position (which I think means it's at maximum contact) it sits perfectly upright and works fine. If I turn it it one position in either direction, it tilts very slightly off-axis and heats noticeably worse.
When I set the Vapman into the well...I have to turn it slightly so it drops into the well and sits perfectly without a tilt. If you have a tilt it has not gone down enough into the chamber. When down into the chamber if you touch the Vapman it moves but, when placing into the well initially you have to kind of find the right circular motion where it just does a small drop in.
Right, but this is after it's fallen into the slots. There's a bit of room to wiggle and seat it, but with some they will not sit evenly no matter. It's a slight amount, like a mm or two, like it's solidly seated but on a slight angle. Not sure how better to describe it but you can see it particularly with a tall MP or by looking at the VM compared to the rim, you'll see the discrepancy. With others you can see that it's perfectly even all around and those seated like that work perfectly.
These were made by The Rogue Wax Works long ago...he has not had any recently but, you can ask him perhaps. https://theroguewaxworks.com/
Viola! That may have done it!Hello vapman family, I just spent the hole day testing all stations with different vapmans to really find out what could be the problem here.
1. I have checked several docking parts and I can assure that they are the same, so no issue there.
2. Each station is calibrated by me and David to the exact same temperature +/- 2C, so it cant be a calibration issue.
So i came to the conclusion that it can only be a positioning problem of the vapman on the docking part.
This can either be caused by a damaged vapman, i.e. a vapman where the pan no longer sits straight in the grip ring due to a bump or similar, causing the vapman to touch the edge of the heating station.
Or the docking part is not perfectly centered and the vapman is not sitting straight because it is touching the outside edge.
Of course, it can also be the case that the vapman is not placed right in its position or is placed on the station at an angle, but than the user is the issue.
we have manually aligned each heating station with the vapman and tightened the screws very firmly, but i would still ask you to check these two variables on your heating station/vapman.
If the docking part is not centered causing the vapman touch the edge of the heating station, there is a simple solution.
1. open the 3 screws by one turn
2. center the docking part by moving it to the appropriate position
3. switch on the station, allow it to heat up and then tighten the screws.
hope this helps!
Thank you Michael and David...it is wonderful to hear from you. My regards to Rene...stay well.Hello vapman family, I just spent the hole day testing all stations with different vapmans to really find out what could be the problem here.
1. I have checked several docking parts and I can assure that they are the same, so no issue there.
2. Each station is calibrated by me and David to the exact same temperature +/- 2C, so it cant be a calibration issue.
So i came to the conclusion that it can only be a positioning problem of the vapman on the docking part.
This can either be caused by a damaged vapman, i.e. a vapman where the pan no longer sits straight in the grip ring due to a bump or similar, causing the vapman to touch the edge of the heating station.
Or the docking part is not perfectly centered and the vapman is not sitting straight because it is touching the outside edge.
Of course, it can also be the case that the vapman is not placed right in its position or is placed on the station at an angle, but than the user is the issue.
we have manually aligned each heating station with the vapman and tightened the screws very firmly, but i would still ask you to check these two variables on your heating station/vapman.
If the docking part is not centered causing the vapman touch the edge of the heating station, there is a simple solution.
1. open the 3 screws by one turn
2. center the docking part by moving it to the appropriate position
3. switch on the station, allow it to heat up and then tighten the screws.
hope this helps!
this is on the menue for me today. i love these lil man so much!
hahaha! the lighter is a xikar turrim single torch. the stash cans are from a swift store and the olive tray and bowl are from a local shop. i loved how it all matched so i bought emYou can’t post such a wonderful picture of a Vapman and other beautiful items and not tell us anything about them, what a tease!
Did it. Positioning is a bit better. Now the station is no longer recognizing the vapman v2 (doesnt start blinking). Older vapman gets recognized and Station starts to blink....Hello vapman family, I just spent the hole day testing all stations with different vapmans to really find out what could be the problem here.
1. I have checked several docking parts and I can assure that they are the same, so no issue there.
2. Each station is calibrated by me and David to the exact same temperature +/- 2C, so it cant be a calibration issue.
So i came to the conclusion that it can only be a positioning problem of the vapman on the docking part.
This can either be caused by a damaged vapman, i.e. a vapman where the pan no longer sits straight in the grip ring due to a bump or similar, causing the vapman to touch the edge of the heating station.
Or the docking part is not perfectly centered and the vapman is not sitting straight because it is touching the outside edge.
Of course, it can also be the case that the vapman is not placed right in its position or is placed on the station at an angle, but than the user is the issue.
we have manually aligned each heating station with the vapman and tightened the screws very firmly, but i would still ask you to check these two variables on your heating station/vapman.
If the docking part is not centered causing the vapman touch the edge of the heating station, there is a simple solution.
1. open the 3 screws by one turn
2. center the docking part by moving it to the appropriate position
3. switch on the station, allow it to heat up and then tighten the screws.
hope this helps!
Outstanding. How beautiful. Super enjoy this...thank you for sharing and I loved it.
Those look like they might be rebranded Infinity Jars. If so, they work very well.
Which are sublime for storing ground buds IME. They aren't cheap but that deep purple tint is gorgeous.Which are rebranded Miron glass jar...
