Marcus
Well-Known Member
Last edited:
Venty by Storz & Bickel
- Thread starter Jill NYC
- Start date
Thunderbelch
Well-Known Member
Finally bricked and disassembled mine
Now it really does look like a big pile of shit!Finally bricked and disassembled mine
vapviking
Old & In the Way
Nice!Finally bricked and disassembled mine
So, one question would be, "which of these components was bad, and how was that enough to warrant scrapping the whole unit? Or might the issue be a cascading event?
It appears to be rather modular.
This could initiate a "mod" phase much earlier than one might expect!
Lots of folks will be keeping for spare parts, which could be great. But before messing around they should know which could lead to trouble.
cptofnthng
Well-Known Member
Maybe s&b reps do what a lot of people in Blbusiness do. Making promises with good hope and to please impatient customers
Dr. G
***Old Resident*** Vapman Collector
Thanks for sharing this...its awesome you were able to take it apart and show us. You mean to tell me that..this is it? I am truly amazed. How sophisticated and yet so simple...put together its the best vape around. Go figure...I miss my Venty like crazy. I started using my TM2 and its super nice...but, I miss my Venty. Period. Need it. Got to have it.Finally bricked and disassembled mine
Strolling&Rolling
Well-Known Member
Last week I was told they hoped to begin shipping again this week.
Hopefully it's not just the company line to say next week every week LOL
Hopefully it's not just the company line to say next week every week LOL
666Honeybadger
Unknown member
And how about the airpath (where are the intakes exactly and how does air travel thru device) and the vaporpath? Anything non-plastic in there (except for the heater)?
Thunderbelch
Well-Known Member
Air enters through the slots on the sides of the oven area (bottom slots have baffles to meter air so enough comes in through the top slots too), past the outside of the heater (so the top slots help cool the outside of the heater), then into the gap between the beige PEEK and black PEEK at the bottom. The electronics and sensors are completely isolated from the oven area by a blue (presumably silicone) gasket just under the heater area. Confirmed all this by blowing ecig vapor through the heater from the top so I could see where it comes out.
Haven't taken the heater apart further as it would require desoldering the heater and sensor wires from the PCB below the gasket, and I don't want to do that at this point.
Just received S&B email stating my replacement Venty is ready to be shipped along with tracking number. Yipeeeeeee
Dr. G
***Old Resident*** Vapman Collector
YAYYYYYYYYYYYYYYYYYYYYYYYYY!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! YAHOOOOOOOOOOOOOOOOOOOOOOOO
HAPPY DANCE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Awesome! Now I'm waiting for an Email notification that it's available in the store again.
Strolling&Rolling
Well-Known Member
That's great news, did the email say any interesting or was it just a generic shipping email?
Are you in US or Europe if you don't mind me asking?
philiegram
Member
May i ask: when did you brick your venty? Right after receiving the instrucions? Just asking so i can find out if it was a first-in-first-out with regards to when one bricked the device…. Thanks!
stressed
Well-Known Member
my venty has been charging down for 24 hours now. it's almost dead but still has life in it. i just want to get this mess over with instead of jumping through hoops. their instructions were kind of vague to me.
- Once the update is successful (meaning that it has been drained) , you will be asked though a pop-up to reconnect your VENTY so that we can receive an update confirmation. If the pop-up does not appear, please refresh the site, click on “connect” and select your device again.
- This last step is important to qualify for a replacement device.
their asses are on fire and they are wondering who is getting fired for this disaster. i don't see how they could tell us that they just found out about a dangerous problem and to brick their device. but hey, all is well after 2 weeks or so and happy days are here again. you don't fix hardware problems that fast.
Hmmmmmmmmmmmm
Last edited:
Simply reconnect. And perhaps you should hurry. Noone said that it should be drained. No idea if you can still do it or if it is too late when it is drained. The update is usually successful in seconds. 3 dots and the bt symbol mean the update was successful.
Not sure where you got the part in parentheses.
"Update is successful" means that the web app has downloaded the firmware update from S&B and installed it on your Venty. THAT is when the popup appears.
You should definitely connect the web app to your Venty while it still has power. Once it's drained, it's a dead brick.
staircase slight of hand
Well-Known Member
I was also confused by this and emailed them, this is what they said:
Please note, the update was successful if the display showed 3 dashes and the Bluetooth symbol, and the device can now no longer be switched on.
You know that the data transfer to STORZ & BICKEL was successful if the following message appeared in the WebApp after the update: "Your device will now discharge slowly".
stressed
Well-Known Member
like i said, the directions are a bit confusing to me. i did what they said to do, i got the 3 dashes and the other symbol. i never got a pop up. not a word about don't drain it completely. my logic told me to drain it completely or they would have stated in big bold letters to not drain it. it is well and truly dead now. it won't turn on even when i plugged it back in. like i said, just send me a new fucking vape and stop with this nonsense. imma go write them a nasty gram and demand my money back. i'm done.
stressed
Well-Known Member
I wrote the line in parentheses. the pop up never appeared. i watched it closely for hours. i
ok, thank you. i guess it worked then. i never connected to the web app as i didn't need it yet. unless the web app means when i turned it back on yesterday, that was the app that i connected to per their instructions. i'm confused, stoned, and need a joint.
it still flashes the 3 dashes and the other symbol once every minute or 2. a slow death. i didn't get an email from them so i was and still am a bit concerned if things worked well.