TinyMight / TM 2

[Shit Snacks]

That's actually not a variable that applies when you are using a regulated device, because then it's not the battery that dictates how many amps will be taken. The max currency discharge indicates what max discharge would still be okay for a battery to give. If that's below the devices specifications, that's just bad luck for your battery.



Balancing low charges to the volts needed is one of the major jobs of the soft- and hardware of a regulated device. I'm quite sure the TM has this feature, because a) it's not exactly rocket science these days (e cig mods have been able to do so for many years on even higher power levels) and b) anything else wouldn't match my experience. As I said, I'm using the battery until it's (pretty much) dead (at ~3.2V) and I have never noticed a decrease of power.

Sorry I meant variables in my own usage where I was not scientific enough to note them when I felt I experienced the drop. honestly a couple times I felt like I noticed the drop in and put them on the charger and they were higher than I expected! Hence very unscientific lol

Regarding the regulation re: amps, I don't know just remember reading a post from @KeroZen about this regarding specifically the Evic and P80 which are regulated mods sooooo

 

[Siebter]

specifically the Evic and P80 which are regulated mods sooooo

While I'm still a young duckling when it comes to vaporizers, I have some experience with e cig boxmods. I literally suck 18650s dry on a daily basis, meaning until the mod says „Low Battery!” or the like, which will usually be at about 3 to 3.2V depending on the mod. None of them decreases in power when the bat gets low – which is important for us e ciggers (a metal coil is more sensitive to change in wattages than a bunch of herbs). There might be some mods that do it better than others when you have a fancy occilioscopometer to measure it (making names up here, have no idea), but in general they will give you the feeling that you always get the exact same power as you have set until the battery is dead. I'm sure both the P80 and the Evic, although not the freshest boxmods these days, are capable of that too.

 

[Abysmal Vapor]

While I'm still a young duckling when it comes to vaporizers, I have some experience with e cig boxmods. I literally suck 18650s dry on a daily basis, meaning until the mod says „Low Battery!” or the like, which will usually be at about 3 to 3.2V depending on the mod. None of them decreases in power when the bat gets low – which is important for us e ciggers (a metal coil is more sensitive to change in wattages than a bunch of herbs). There might be some mods that do it better than others when you have a fancy occilioscopometer to measure it (making names up here, have no idea), but in general they will give you the feeling that you always get the exact same power as you have set until the battery is dead. I'm sure both the P80 and the Evic, although not the freshest boxmods these days, are capable of that too.

This cause with e-cig atties you need very little power over a short period of time and it is not that noticable.. I could max the 70w limit on the TUBOevic easily and with the battery drained halfway,it had even more trouble with overly heroic draws .. Also using the PA provides me with 4.2v all the time and it feels like a freshloaded battery eachtime.. ,and that feeling is there cause it is hard for single battery to keep up with heaters like that when battery charge drops.

 

[Siebter]

This cause with e-cig atties you need very little power over a short period of time and it is not that noticable..

Well, some e cigs draw *a lot* of power (150 watts, sometimes more). I'm a low watt vaper, I would definitely recognize a drop even by only 1 or 2 watts. Beside that it's very true, a cruise mode would probably make things look a little different, although I'm not sure how it exactly works. However, the TM will not draw high constant power, both in session and even less so on-demand, so it will have an easier time recovering from voltage drops (than a mod in cruise mode might have). My point was that keeping up the power at the same level regardless of charge is very doable and I'm sure that's what the TM is aiming at too.

Edit: Whooo @Abysmal Vapor – 4000 posts! :-)

 

[dzoinp]

So it’s not that I had what I was looking for !!The BENDY SPIKED works just as well as on the TP80 !!
Attention is not a stable fit ... I had to remove the ring to seal the stem in the oring slightly.
ONLY FOR THE TEST PURPOSE

 

[Temple]

What grind are people finding works best for the TinyMight. Coarse, Med or Fine?

 

[david8613]

How long is the waiting list for a tiny might?

 

[Shit Snacks]

What grind are people finding works best for the TinyMight. Coarse, Med or Fine?

I like medium, but it works well with all three, depending on your screen and stem set up... I wouldn't go too fine with the stock setup, with basket or directly on cooling unit screen, though it does still work well it could dirty up the cooling unit faster... However, best is tough to say!

 

[Brewervapesalot]

Nop... already removed!
Too much air flow reduction.
I'm back to the original domed screen without the CU screen

Totally agree fine screens screw tiny might performance

 

[lauantaimakkara]

I’m quite new to vaping and I’ve read a lot about it but one thing I don’t understand is the screens. Is there some tutorials or videos about the screens? How and why should I use them and Where should I buy them in Europe? Or are those screens normal pipe screens which I can buy from any shop that sells waterpipes ?

Is their function to keep the vaporizer more clean?

 

[DonMarteng]

I’m quite new to vaping and I’ve read a lot about it but one thing I don’t understand is the screens. Is there some tutorials or videos about the screens? How and why should I use them and Where should I buy them in Europe? Or are those screens normal pipe screens which I can buy from any shop that sells waterpipes ?

Is their function to keep the vaporizer more clean?

You should use a screen to keep your herbs in place and not suck them into the cooling unit, this way you can avoid cleaning it too often.
Also this counts for 99% of all vapes: it works best clean! Taste and airflow are at its optimum then.
Cant tell you the exact size of the screens since im still waiting on my TM, but im sure its some standart size you can get fairly easy elsewhere!

Can anyone tell me how long it is from complete to shipped?
Mines complete since 31.01. and no updates yet, im just getting more hyped about this thing everyday (ordered 17.01. btw)

 

[lauantaimakkara]

Can anyone tell me how long it is from complete to shipped?
Mines complete since 31.01. and no updates yet, im just getting more hyped about this thing everyday (ordered 17.01. btw)

Thanks for the info!

I heard they “complete” the orders because of that 30day PayPal-period so it doesn’t actually mean anything.

 

[karec]

I’m quite new to vaping and I’ve read a lot about it but one thing I don’t understand is the screens. Is there some tutorials or videos about the screens? How and why should I use them and Where should I buy them in Europe? Or are those screens normal pipe screens which I can buy from any shop that sells waterpipes ?

Is their function to keep the vaporizer more clean?

It helps to keep the vape clean if you put between the flower and the CU, @dzoinp had use a similar one and took off the original but got back to use the doomed one ... myself im using this on the end of the stem to prevent any flower to come off, and this way i dont need to turn the vape upside down to load and helps when i need to stir since gives enough space to use a picker or just shake it, i ordered from Ebay, i found a pen that fits in the stem tightly and made the shape using it.
"100 Stainless Steel Tobacco Smoking Metal Filters Smoke Pipe Screen 19MM 0.74"

It also took me 3 weeks from the order to arriving, i made the order on the 27/12 maybe there is more people but 30 days +-, i ordered from the makers page.

Not heard back from glass blower yet, but got my ideas down on paper today (based on the stock 80mm stem)...
[Im not a glass blower, and so don't even know if it's possible]

i would totally love to have one stem like that... but if you could insert the CU would be great cannot understand is its possible that way... bottom part i would make like the OG TM stem but the top i would love to have as in the drawing.

Cheers

 

[Sensory Leaf]

i would totally love to have one stem like that... but if you could insert the CU would be great cannot understand is its possible that way... bottom part i would make like the OG TM stem but the top i would love to have as in the drawing

With the 80mm stem, leaving 10mm for a bowl, I don't think there would be enough room for the nipples and the taper... Obviously the length of the stem isn't confined to 80mm, and could be made longer

As I have it in my drawing; it only leaves 49mm in length for the nipples and the taper, I'm concerned that's a little tight

 

[im not a robot]

Can anyone tell me how long it is from complete to shipped?
Mines complete since 31.01. and no updates yet, im just getting more hyped about this thing everyday (ordered 17.01. btw)

hm - i ordered mine two days earlier & my order is still listed as pending. maybe the status is not so reliable? maybe they like you better. has your paypal payment gone through yet ? mine has not, i imagine they will complete the payment process once the parcel is ready to be shipped. finland to central europe delivery should take ca. 2-3 days i am guessing?

edit: oh. it could be possible they are changeing the stealth behavior of my unit, and that would obviously & rightfully take longer. i asked them whether it would be possible to disable the led in stealth, just haven't received a reply yet

 

[DonMarteng]

hm - i ordered mine two days earlier & my order is still listed as pending. maybe the status is not so reliable? maybe they like you better. has your paypal payment gone through yet ? mine has not, i imagine they will complete the payment process once the parcel is ready to be shipped. finland to central europe delivery should take ca. 2-3 days i am guessing?

My paypal got charged once it went to complete, so I guess it doesnt really say a lot
Ill let you know once i receive mine and you do the same please
I heard the shipping is like 1 day super fast but dont quote me on that!

 

[im not a robot]

Ill let you know once i receive mine and you do the same please

thanks! will do too

 

[Sensory Leaf]

I heard the shipping is like 1 day super fast but dont quote me on that!

I ordered some accessories last week... He shipped by DHL, and it arrived (in the UK) next day

 

[tokenknifeguy]

Anyone use the long stem? Most pics I see is with the short stem, wondering if the long stem is even needed? Also, is there a waiting list, or do you go ahead and place your order and pay? I think I need to get the ball rolling.

 

[Sensory Leaf]

Anyone use the long stem? Most pics I see is with the short stem, wondering if the long stem is even needed? Also, is there a waiting list, or do you go ahead and place your order and pay? I think I need to get the ball rolling.

I use the long stem. (Imo) It's not necessary as the cooling unit does a good job. Extended use/back to back draws, can lead to the glass getting warm (not uncomfortable by any means) but the long stem mitigates this massively.

AFAIK it's in pre order stage still, so you order is not fulfilled immediately.

 

[Siebter]

@ screens – there seems to be quite some confusion about this topic so I'd like to point out that extra screens are not necessary per se. This is my screen after 5 days of usage and about 20 sessions:

I never use extra screens in front of the cu and hardly do I have to brush the screen of the cu after a session. I will usually brush the walls of the chamber, that's it. However, I also never stir during a session, and that might play a role here. When stirring, extra screens might be necessary to prevent the cu getting dirty too soon.

 

[MonkeyTime]

@ screens – there seems to be quite some confusion about this topic so I'd like to point out that extra screens are not necessary per se. This is my screen after 5 days of usage and about 20 sessions:

I never use extra screens in front of the cu and hardly do I have to brush the screen of the cu after a session. I will usually brush the walls of the chamber, that's it. However, a also never stir during a session, and that might play a role here. When stirring, extra screens might be necessary to prevent the cu getting dirty too soon.

I'm jealous, mine aren't that clean after one bowl. But right now everything seems dry while being kept with 62% bovedas, the air is just too dry.

 

[Siebter]

I'm jealous, mine aren't that clean after one bowl. But right now everything seems dry while being kept with 62% bovedas, the air is just too dry.

I'm not sure the used strains or their condition have a great impact on that, because I have used about 15 different strains in the TM (I'm using 62% Bovedas as well) with various grinds and all of them were nice to the cu's screen. More resinous strains will gunk it up faster, but mostly the inside of the cu, not the screen.

It might also be because I developed a routine that tries to keep things clean in general. I will make sure that the load sits fluffy, yet firm enough to stay where it is when being turned upside down. After a session I will usually be able to blow the herb out of the stem, it will stay in one piece most of the times. That's why I brush the walls of the chamber a bit, they tend to get sticky fast and will prevent to eject the load that way after the next session if not taken care of.

 

[LabPong]

Stems will get gunked up if you have sticky greens!

I clean my stems every 6-8 bowls because of this. But I do have some strains that are not too sticky and I can go much longer before cleaning. Temp levels also play a factor....high temps will keep it cleaner.

 

[Tweakz]

I still can’t pay for my TM, and you tease me with a lot of photos and videos. as well as laudatory reviews. life is pain