Discontinued The Persei Vaporizer for herbs and concentrates.
- Thread starter THC SCIENTIFIC
- Start date
elmoe420
Well-Known Member
You always need to use the supplied fuse with any battery config on the 8.
SamuraiSam
Extraction Technician
If you're using the dual coil try the single on the smaller battery.
Do one thing, try it out on the full size 8 and see if that still works, in case you had ever tried to use the 8 top without the fuse in any battery configuration.
Do one thing, try it out on the full size 8 and see if that still works, in case you had ever tried to use the 8 top without the fuse in any battery configuration.
Still won't fire
Are you using AW batteries? Also a single 18350 might not be powerful enough have you tried an 18650 to see if the cart fires properly at 3.7?
ragnorokk
DERP
You just need an AW 18650. You can adjust the spring on the 8 long tube to accommodate either 2x18350 or 1x18650.
The short tube is for a single 18350 but a single 18350 seems to be best used on the standard kiss carts and older essential oil carts the herc and alpha c I belive draw too much power for a single 18350 to perform properly
Edit: I've also been told recently you can stack both tubes to accommodate 2x18500 which I am very interested in trying myself soon
Edit: I've also been told recently you can stack both tubes to accommodate 2x18500 which I am very interested in trying myself soon
ragnorokk
DERP
Package arrived. Can't wait to spend some time with the 7.4v donut and give feedback.
@THC SCIENTIFIC what is the recommended range for operation of the 7.4v KISS Alpha Centauri 1701?
@THC SCIENTIFIC what is the recommended range for operation of the 7.4v KISS Alpha Centauri 1701?
Last edited:
I am going to try the 7.4v donut tonight also
@ragnorokk I have been using my 7.4v Donut with 2 aw imr 18350s. You are using The Core? On fully charged batteries it hits hard with flavor. I'm not riding the button just extended presses. If you dal it down a bit you may be able to get setting where you can just ride the button. I wouldn't venture much above 7.4v without @THC SCIENTIFIC or @SamuraiSam's 
.
.
ragnorokk
DERP
Yeah, I loved the 3.7 donut @ 4.8 until I murdered it (manslaughter? Techslauter? I swear it was an accident!). I had been trying it @ spots between 3.7v and 4.2 and just hated using the wick. I couldn't find a setting I thought was worth a damn. As soon as G posted the comment that up to 5v could be put through it without incident, I set it to just below his max recommendation and had a blast. Thus, I'm waiting in anticipation for @THC SCIENTIFIC to post this donut's operating range as well, in hopes of avoiding both breaking the donut messing around w/ higher voltage as well as lackluster vapor production from too low of voltage input (aka Splattertown, USA).@ragnorokk I have been using my 7.4v Donut with 2 aw imr 18350s. You are using The Core? On fully charged batteries it hits hard with flavor. I'm not riding the button just extended presses. If you dal it down a bit you may be able to get setting where you can just ride the button. I wouldn't venture much above 7.4v without @THC SCIENTIFIC or @SamuraiSam's
the donuts safe range is 3.0v - 4.2v, even then you have to learn to pulse the button on the top range. If not using the black ceramic, you can go up to 4.8v but pulsing the button starts as higher to go.
You have to re-seat the pins and adjust the button pin.
i recommend pull the top pin and look inside while you push the button, if the bottom pin is being pushed back by the button back out the button screw by about 1/8th of a turn until it makes contact but the pin barely moves at all then reassemble you should be firing nicely after that also make sure the gold nuts on the top pin make good contact with witch ever cart your using
ragnorokk
DERP
The 8 can be touchy. You'll have to have SamuraiSam do a video chat with you to get everything set up -- he does an awesome job pointing out what should go where and making sure everything is set up right.
whats the safe range for the 7.4, though? And if we're using the ceramic wick, we should stay in battery voltage range?
Last edited:
The 8 is designed to be totally user serviceable, what we recommend for everyone is when you get the 8 tear it down and reassemble it to get a feel for this unit.
This unit is designed to work no matter what the issue is. This means if its our of sync it has to be re adjusted, it is a mechanical mod. Wont fail and even if it does it will still work in limp mode 100% until you replace the springs.
@ragnorokk
1701 best range is 3.0v - 4.2v with the occasional pulsing of the button on the higher end, when moving away from this range and into the 4.3-5.0v range then pulsing the button comes regular.
ragnorokk
DERP
gotcha. At 4.8, I was definitely pulsing and got amazing results; instacloud. I think what killed it was that I had my core set for herc and thought it was set for the 1701.
I tried the 3rg gen dual coil KISS cart tonight @7.4v; Awesome. Back to the KISS mentality w/ the simpler design. Very tiny profile. It's thinner than my Omicron... does it match some other w9 product?
What do you mean match other w9 products?
ragnorokk
DERP
Just curious if it is the same outer diameter as one of the non Persei/omicron units (minicron, etc).
Yes the kiss Gen 3 is the same diameter as the Minicron and Ophos, which is 14 mm