I do need to buy a multimeter either way, I'll do that on my way home tomorrow.
Any other obvious shit I could be overlooking?
in fact to further reinforce the battery thing, I hadn't charged the 18650, so that may have not even been ready to heat up a cart.
Is it possible to run dual 1.5 carts?(3.7v) the battery(3.7v trustfire protected) works on single 1.5Ohm, but not dual?! I have AW imr 18650's 2000mah on the way if my battery is the issue! Thanks for the info, as always.
same. my dual top is near the end of it's life anyway and it has worked so far.Yup, dual 1.5's on a AW IMR works great. It pushes the limits of the 5a persei top...never stopped me though.
Yup, dual 1.5's on a AW IMR works great. It pushes the limits of the 5a persei top...never stopped me though.
I can't believe that they awarded the HT Medical Cannabis Cup gold medal for best product to a grinder with a built-in ashtray !!!
Silver to a domeless nail !!
and bronze to a "grinder card" that fits in your wallet???
WTF !!!!!!
hey guys, im back and proud to say that yes we didnt win, but we did win Best hybrid.
Larry OG Grown by us, Cali Connection Genetics.
1st Place baby.
Thats Trophy #2.
hey guys, im back and proud to say that yes we didnt win, but we did win Best hybrid.
Larry OG Grown by us, Cali Connection Genetics.
1st Place baby.
Thats Trophy #2.
Excellent! Congratulations!!! So how long before the Larry OG 'pre-fills' are available?? LOL
NoName
And, for those interested in the battery ordeal that was had here it has been solved. The 3v cr123a cell received was a dud. Multimetered it and it read at a whole .16v. Even on the battery it says 3.6v at full charge and 2v at empty. So has been solved. Going to open D9 ticket. Any way to test carts with a multimeter? either live or independently? OF would probably know.... Lost a couple carts to the battery ordeal i believe.
Porq
OF posted a detailed set of instructions for cart testing with a meter in the Omi thread I believe. Essentially you measure the carts impedance between the bottom center pin (on the threaded end) and the cart casing. Hope this helps.
hey guys, im back and proud to say that yes we didnt win, but we did win Best hybrid.
Larry OG Grown by us, Cali Connection Genetics.
1st Place baby.
Thats Trophy #2.
Hey I was just thinking about getting some too!
Nice price/potency:
Congratulations on the win! That is one of the things I would like to accomplish someday!
Great news, sure smelled like that was it but you need other tools (or spares) to pin it down.
Sure, you can use your new meter to check 'em.
Set it to the lowest Ohms range (probably 200 at about six o'clock on the dial). The display should go to over range (usually 1 with 3 blanks). Touching the probes should make it go to zero. It won't quite make it because the leads and connections have resistance so it'll probably stop at one point something. Remember this number if you want the most accurate answers but now hold one probe on the threads and use the other to probe the hole in the center pin.
Easy, once you see it happen.
Good luck, and again, well done on the troubleshooting!
OF
Tested the two that were presumed doa. One 5ohm was lost, the other 4 ohm was fine.
I can't believe that they awarded the HT Medical Cannabis Cup gold medal for best product to a grinder with a built-in ashtray !!!
Silver to a domeless nail !!
and bronze to a "grinder card" that fits in your wallet???
WTF !!!!!!
THC SCIENTIFIC said: ↑
hey guys, im back and proud to say that yes we didnt win, but we did win Best hybrid.Larry OG Grown by us, Cali Connection Genetics.1st Place baby.Thats Trophy #2.