Discontinued The Hammer Vaporizer

pakalolo

Toolbag v1.1 (candidate)
Staff member
Damn something is wrong with my hammer. It just wont ignite now at all even though its definitely getting enough butane. You guys have any ideas how to fix it?

Did you fill it recently? I might be a butane klutz, since I've had this problem with lighters and that's always been the cause. Somehow I get air in the tank during filling, so I get the hiss and smell of butane being released but it won't ignite. I can usually cure it by thoroughly purging the device, turning the flame adjustment down as far as possible, and then filling carefully and completely. I find butane devices to be cantankerous, but to be fair I never had this happen with the Hammer while I owned it.

The other possibility is a failed igniter. As I understand it, you can replace the igniter in a Hammer but I haven't done it.
 

FlyingLow

Team NO SLEEP!
Loving my hammer for travel. No worries on airplane/airport with fully cleaned stems. I've found it great for the beach and other windy locations as well.

Only problem with travel is that I most always end up having to use Ronon due to being in small cities without head shops and I am not able to fly with butane... I find ronson burns pooly, and does not maintain a high of temps- so I have to bump up the tune by a notch or two.
 

Hammer Vaporizer

Well-Known Member
Manufacturer
Hey FC,

I apologize we haven't been active for a while, but I can assure you it's been for good reason. We've been planning a huge crowdfunding campaign that we are super excited to finally be able to share with you. We just launched on Indiegogo moments ago and this is the first place we've come to start sharing the details with our favorite Hammerheads on the net. You all were incremental in helping us decide on the upgrades to the Hammer PRO, so we truly thank you all for your feedback and support!

To kick things off, I'll let @Head Tools (aka David) tell you more...


Now we need your help to transform the Hammer Vaporizer into the:

20141107111121-hammer-pro-vaporizer-ig-big.jpg


I know many of you are already familiar with the Hammer and all the positive feedback we've received from reviewers and users around the world, so I won't repost all of that. The important thing I know you all want to know is what's been changed, so I'll leave you with one more image that I think will be helpful.

20141113103244-hammer-pro-whats-new.jpg


Please visit https://www.indiegogo.com/projects/the-hammer-pro-vaporizer/ to check out and share the project. We are going to be dropping a lot more exciting stuff as the campaign goes including a referral program, t-shirt design contest, surprise rewards, stretch goals and more. We created a $1 contribution level for those of you that just want to stay updated and a $15 stems only contribution level for those of you that may already have Hammers and don't want to upgrade, but still want to support the campaign.

Please let us know if you have any feedback or questions about the project. We want you all to be a part of shaping this campaign over the next 34 days as much as you were a part of shaping the design of the Hammer PRO. We know how much you guys love the Hammer Vaporizer and with your help, we can spread that love and help more even more people GET HAMMERED with us by supporting the Hammer PRO on Indiegogo. Stay tuned for more updates soon...
 

davesmith

Well-Known Member
Glass Blower
I'd like to know a bit more about this built in nail? And will we old hammer users still be able to get the gaskets?

Cheers
 
davesmith,
  • Like
Reactions: RUDE BOY

LuckySeed777

Well-Known Member
@Head Tools I think you used my custom stem for the campaign.I feel so special! I really miss that little guy. Was my favorite way to use the hammer. David makes them really strong and they are so nice to vape from. Unfortunately mine fell out of my lap from my lifted jeep and onto the concreat floor, it bounced and landed on the side of the bowl. I could tell it didn't want to break. but...
hGKUT1d.jpg


I couldn't belive it didn't break instantly from so high. Some day soon I'll buy another.

Wish I had the spare money to contribute. I love my original hammer and know what you guys put out is gonna be great. goodluck!!
 
Last edited:

Head Tools

Well-Known Member
Manufacturer
My apologies to you Scott... we did receive your email, but were a bit distracted by the launch of the campaign. I have a solution to your problem and will reply to you asap.

NO MORE wispy HITS
David
 

Scott A

Well-Known Member
My apologies to you Scott... we did receive your email, but were a bit distracted by the launch of the campaign. I have a solution to your problem and will reply to you asap.

NO MORE wispy HITS
David
Thanks David. I completely understand you guys being busy right now. Im probably gonna get in on the campaign for a hammer pro some time soon.
 

Hammer Vaporizer

Well-Known Member
Manufacturer
Always wanted an analog vape and now Hammer Pro #2 is going to me :rockon:

How do I pay the $25 for Europe shipping?

There was likely a place you could have added the extra $25 when you first checked out. I think now you will just have to go back to the campaign page and contribute a custom amount for $25. I will make a note when I see the transaction that it is for shipping of your Hammer PRO.


I'd like to know a bit more about this built in nail? And will we old hammer users still be able to get the gaskets?

Cheers

Replacements will continue to be available for both the front lock-on gasket and new rear gasket which comes pre-installed on the Hammer PRO. The built-in nail just refers to using the heat exchanger as a nail, which some innovate hammer users like @paytonpenn have been doing for a while. We just never really promoted it as a feature until now.
 
Hammer Vaporizer,

Dramma Lamma

Looks like a job for!
I went ahead and made my contribution to the fund and got one with the WP adapter.

I would really like to see other WP adapters tho, just 1 size and style is kinda a bummer. Have you also got a price point for a replacement or custom WP adapter size/style? I would really Like a 18MM Female one.

Also to be frank the price of the WP adapter itself is a bit much IMO considering you get two mouthpiece's which is more glass for $5 less. A small comparable sized GonG size adapter with 2 joints is only $8 at a head shop so it can't be price driven by the cost of a single GonG ground joint. So why the hell is one tiny little WP adapter $20? That is a bit over priced, or at least give us 2 for the $20. I can see my friends doping it and needing replaced sooner than later.
 
Last edited:
Dramma Lamma,
  • Like
Reactions: $unnyblaq

davesmith

Well-Known Member
Glass Blower
Replacements will continue to be available for both the front lock-on gasket and new rear gasket which comes pre-installed on the Hammer PRO. The built-in nail just refers to using the heat exchanger as a nail, which some innovate hammer users like @paytonpenn have been doing for a while. We just never really promoted it as a feature until now.


So there's no difference in terms of dabbing?

When's the rear gasket going to be available for use Hammer 1.0 users?

Cheers guys
 
davesmith,
  • Like
Reactions: KidFated.

Head Tools

Well-Known Member
Manufacturer
The Hammer PRO does actually include few tweaks to the heat exchanger for better use with concentrates. However, the original Hammers will also perform the job without any issues.

If you haven't tried your Hammer with concentrates... You are missing out!

Seriously better than any rig setup you've tried... like an e nail in your pocket. The heat exchanger is designed to maintain lower temps which means that you get the best flavor without any "scorched taste"

NO MORE wispy HITS
David
 

Philreal187

Well-Known Member
I believe I have a friend who only smokes looking into the hammer. I mentioned to be patient and put 79 up for the new units fund raiser, but I have a feeling he's gonna jump on the original which is still a quality vape. Im pretty excited to see what changes the 2.0 has but I couldn't be happier with the OG hammer. Thanks @Hammer Vaporizer & @Head Tools for keeping us up to date with whats new.
 

wax

Well-Known Member
Does anyone have more info on the hammer pro? I saw the video on indiegogo aND it looked. Awesome. I've never used a butane vape does anyone know how this one works exactly ? Do you have to hold the torch or does it clip on because that's what it looks like in the video
 
Top Bottom