Discontinued RBT Splinter (All Versions)
- Thread starter RastaBuddhaTao
- Start date
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Yup this is correct, sometimes it is referred to just as Splinter Z (vs ZV2 and US custom) which is how they list it on planet vape... It will be the cheapest of all the Splinter Z models, and it should be noted that the build process is not as perfected as it was with the later blackwood ZV2, so there could be manufacturing defects like cracks in the wood or other superficial imperfections.
bossman
Gentleman Of Leisure
There's a ZV1 that looks more like a custom bubinga on r/entexchange with a UK seller just FYI. He's looking for a trade but still
MikeRotchHertz
Well-Known Member
bossman
Gentleman Of Leisure
I'm in the minority but I don't lock resistance on my Splinter mods.
I've been enjoying TCR between 130 and 165. I have all my Zs set to max 50W rather than 45W so I'd bump that first. With just those settings and the unlocked cold resistance of a Z I get clouds from the first hit at temps down to 350°.
I have a wenge Z and a ZV2 each on its own Ravage both are excellent with the settings above.
In case it matters, I mostly use LG HG2 cells and never drain them below 65 or 70%.
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Still kind of struggling with my ZV1 on the G3D with tubo firmware, been keeping TCR at 160 now with algo off and tried adjusting resistance but still came back down to .392 which seems close to what it's cold value should be though I'm not getting consistent readings... It is kind of working, but I have to use much lower temps, like I can vape a whole bowl to dark at 320 lol suppose I can put my wattage to 50 and see if that makes any kind of difference but I don't see why?
jbm
Well-Known Member
I’ll try bumping it to 50, but it’s weird how the exact same settings (aside from measured cold resistance) aren’t producing on the Ravage. Pretty much the same settings are also working great on an Espion. And both my Zs rip on duals. Do you set PID ever? Does it matter?
As for cells I use a mix of hg2s and Vtc5as.
As for cells I use a mix of hg2s and Vtc5as.
bossman
Gentleman Of Leisure
I haven't fucked with pid myself.
If you're getting good results with the Espion I agree it doesn't make sense. My Ravage kicking so much ass with Red Panda and an easy config was why I tried the Espion in the first place. Both work great and both have identical settings. One of my Ravages was at TCR 165 for a bit and predictability running hot. It has since been switched to TCR 135 like the others.
vapviking
Old & In the Way
What a difference fresh batteries can make!
I'd been using the same batteries (6 total) for what turns out has been just around a year and a half. (in 2 mods, 2 or 3 devices that power this way)
Got some new Molicel P26A's and have used first pair in the Ravage 230 with Splinter V1+ on it.
I'm a very happy guy! Just finishing 6th bowl and it appears there will be a couple or a few more before batteries need a charge.
The old HG2's were getting me about 4.
It seems this is a lesson I have to keep re-learning...my previous times were with Grasshopper batts...
I'd been using the same batteries (6 total) for what turns out has been just around a year and a half. (in 2 mods, 2 or 3 devices that power this way)
Got some new Molicel P26A's and have used first pair in the Ravage 230 with Splinter V1+ on it.
I'm a very happy guy! Just finishing 6th bowl and it appears there will be a couple or a few more before batteries need a charge.
The old HG2's were getting me about 4.
It seems this is a lesson I have to keep re-learning...my previous times were with Grasshopper batts...
androponic
vaped.
Chinese - Female 19/22 Joint - 120mm (100)
www.mountainglass.com
nachooo
Well-Known Member
Thanks..but I think I read somewhere in this thread that those glasses were not suitable for the US custom Splinter Z...If I remember well someone said that they are only good for Splinter Zs..but not the US custome ones..I am a little confused about this...i believe this is it. hopefully @MikeRotchHertz can validate as he has done these repairs. i know you will need to cut the tubing end to the correct length using a diamond cutting wheel.Chinese - Female 19/22 Joint - 120mm (100)
Sadly they charge 50$ for shipping to Europe....That is too much in my opinion...
jbm
Well-Known Member
It turns out cutoff was set to 10 seconds. Works fine now.
MikeRotchHertz
Well-Known Member
That is correct, the mountain glass one is only suitable for Chinese glass repair (Vs and mi3). When I last did a custom and mi2 repair, I was able to grab both of those from KGW, but I don't think that is an option now.
@Unklmark68 any chance you have any to sell to repair our wounded soldier?
Also, I'll try googling for some EU vendors for 19/22 female joint glass and compare dimensions
nachooo
Well-Known Member
Thanks for the info.. I am really in the need of fixing this issue cause no vape is giving me the splinter z feel... If you find a suitable vendor for the female joint of the us custom splinter Z..please notify me.. Thanks again!
Unklmark68
Well-Known Member
@nachooo
I have some Custom Z glass, but I'm not set up to ship internationally,Message me maybe we can work something out....
SquirrelMaster
Well-Known Member
@Unklmark68 has a really nice bubinga Z with blue glass on auction on Instagram if anyone is looking.
I pulled out my Z last night as I was jumping through devices and was reminded why I love it so much. @RastaBuddhaTao made a post on Instagram as well that makes me think RBT may be coming back? Hell yeah is all I need say.
I pulled out my Z last night as I was jumping through devices and was reminded why I love it so much. @RastaBuddhaTao made a post on Instagram as well that makes me think RBT may be coming back? Hell yeah is all I need say.
Unklmark68
Well-Known Member
Do you believe in reincarnation????
SquirrelMaster
Well-Known Member
Hmm I don't see it now but I thought he made a post. Maybe it was on his story, I can't recall.
arb
Semi shaved ape
No and for a marketing pitch this one needs some work.
Why are you so dodgy about answering questions about the heater alloy in your neo?