Joaon

Well-Known Member
Yesterday, after some weeks without bubbler (thanks, cat..), I decided to hack something to make one myself. It ended up with that :


A bottle of Monkey Shoulder (whisky),

her own cap as joint (cork-wood),
a vanilla pod Glass tube as downstem, and a bit of trickerish :myday:

NMro3lr.jpg

Mounted with my desktop vaporizer, the Herborizer Ti



HsFE2EO.jpg

Mounted with the Omnivong Burl :luv:



Water filtration is back ! Smoooooooth ! :cool:



:ninja:
 
Last edited:

Ricardo

Well-Known Member
I just tested this, here's exactly what I did: Just using the body and condenser/mp, I unthreaded the mp just a bit and stuck it in the body. I can see the condenser on the other end. If I twist counter clockwise, the condenser appears to do nothing until I push the mp so it's flush to the body again. Then the condenser is clearly sticking out a bit. Now, if I twist clockwise, I can see the condenser shorten and move back inside the body. No pushing on the mp to make it flush required.
So yours seems to be working OK now. My condenser just spins and spins.
It sounds like the inner diameter of your body could be too large. If you have any organic hemp or cotton you could try wrapping some around the two o-rings closest to the mouthpiece. That might add enough friction to make it work.
Thanks - tried that to no effect. Looked like a botched plumbing job :(
 

flotntoke

thoroughly vaped
Guys Is there any product similar to Dynavap?

Just the various VapCaps. Why? This is the place for one of the most innovative vapes to ever hit the market. Prices are more than fair for every configuration. Not sure why anyone would be looking for something else "like" this.

This is the vape! DynaVap is where you get one (or one of the authorized retailers).
 

darbarikanada

Well-Known Member
Guys Is there any product similar to Dynavap?

in a way, the vapor genie: a flame heats a piece of (I believe) pumice, which then heats the air passing through it on the way to the cannabis. I've got one, never really liked it; you have to stir it - a lot - to get full extraction.
 
darbarikanada,

sunnyblaq

Well-Known Member
So I've tried most of the butane vaporizers other then this bad boy and now VAS has hit strong. I just got a VG coil and love it for size and ease of use but now I'm thinking this would be a great addition. I love that this vape is so cheap 35 for the entire level is what drew me in like the VG coil the VC for 35 seem unbeatable. I prefer butane powered vapes so I can't wait to compare to my already personal fave vape the VM. Soon I'll have the VC the VG and VM all butane powered beauties and come back to give my opinion on the best of the three I can't wait. I will have get a TI woody once my testing is done thank you all for the awesome c pics which pushed me to order the OG and see what's up. My only question is which is better the OG with two carb holes or one?? I feel like one should be fine but want to see what others say.
 

Quetzalcoatl

DEADY GUERRERO/DIRT COBAIN/GEORGE KUSH
So I've tried most of the butane vaporizers other then this bad boy and now VAS has hit strong. I just got a VG coil and love it for size and ease of use but now I'm thinking this would be a great addition. I love that this vape is so cheap 35 for the entire level is what drew me in like the VG coil the VC for 35 seem unbeatable. I prefer butane powered vapes so I can't wait to compare to my already personal fave vape the VM. Soon I'll have the VC the VG and VM all butane powered beauties and come back to give my opinion on the best of the three I can't wait. I will have get a TI woody once my testing is done thank you all for the awesome c pics which pushed me to order the OG and see what's up. My only question is which is better the OG with two carb holes or one?? I feel like one should be fine but want to see what others say.
I have the OG with one carb and found the airflow through that to be a bit much for my specific usage pattern. Did the rolling paper carb mod to make it a little tighter draw and that's where it's been since I put it on months ago. Two carbs gives you more room to play with, if you find you don't like it and want one you can just stick a bit of rolling paper over one of the carbs and not poke holes in it, effectively leaving you with one open carb.
 

mucsusn

60 going on 20
Always watch this amazing and very active thread.....several times a day. I'm at a place in my life where I'm spending most nights with my wonderful new (9 mos.) girlfriend, and I don't have the regular mancave setup available....that being said, I am currently VC'ing about 90% of the time, absent visits to the home base. I have 4, 2 being set at half capacity, and 2 at full depth. I basically load all 4 every morning, and they get me through the day on about .27g of flower. In other words, medicated as much as I need on 2g per week. Amazing little beasts, these are......., now just to get my power supply sorted out on my new WoodScents!
 

towtow

Active Member
Hi everyone,

Just receive my omni titanium with a complimentary glass body to watch it perform.
And also a vapcap-s with complimentary adjustement to make an OG.
Everything well packed with the dynavap tubes. Customer service was the best I have ever talked to, for real.
Time to give it a try, thanks again for all the help I get from here.

Have a great day folks.
 

SSVUN~YAH

You Must Unlearn, What You Have Learned...
@SSVUN~YAH SWEEEET!!!!

Awesome collection!!! Love that Ebony, that Burl, that Cocobolo. Love them all. I hope you give them all personal attention every single day!
Thanks, I try my best. :lol:

What kind of wood is the fifth VC over from right? That's a beautiful collection you have there.
I fell off my chair when I opened. I call it my who dey vape,
because i looks like a Bengal tiger! I would guess Amboyna? :hmm:
 

TheVaporist

Man is a universe within himself
@SSVUN~YAH, are you trying to start a VapCap museum? :o
And those Thuya from the WS... :drool:



Before my battery went off I took this, a little comparison between the old and the new Omni condenser / mouthpiece assembly :
IMG_5756.jpg


The overall length of the new system is 1mm more than the older one (seems more in the picture, perspective deformation)

The threading is different: an older mouthpiece can't match a newer condenser (the contrary is also true).
The threading is shorter on the newer condenser but lead to same amplitude.

The grooves where the orings sits are deeper and the mouthpiece sits more tightly in the body than the older one.

The new mouthpiece is wider than the older one (a few microns more, causing the tighter fit).

I think that's all, I hope that it'll be useful for someone!
Now let's get back to work :science:
 

SSVUN~YAH

You Must Unlearn, What You Have Learned...
@almost there
Lol, George and his crew come up with so many cool additions that I have a lot to live for!

@WakeAndVape
I hope that never happens but you're invited either way!

@TheVaporist
If I do, I wouldn't use my photos, but a professional like yourself!

@phattpiggie
Nope @Squiby is queen bee and @NickDlow is the log king. I'm probably just a court jester or something. Look at what you finally taught me about replies, I'm a slow learner.
 

GreenHopper

20 going on 60
@SSVUN~YAH, are you trying to start a VapCap museum? :o
And those Thuya from the WS... :drool:



Before my battery went off I took this, a little comparison between the old and the new Omni condenser / mouthpiece assembly :
IMG_5756.jpg


The overall length of the new system is 1mm more than the older one (seems more in the picture, perspective deformation)

The threading is different: an older mouthpiece can't match a newer condenser (the contrary is also true).
The threading is shorter on the newer condenser but lead to same amplitude.

The grooves where the orings sits are deeper and the mouthpiece sits more tightly in the body than the older one.

The new mouthpiece is wider than the older one (a few microns more, causing the tighter fit).

I think that's all, I hope that it'll be useful for someone!
Now let's get back to work :science:

Thanks for this, useful to know the differences. The newer model definitely seems more refined, it's tough getting those O-rings off and on again, the pinch trick works but it's fiddly.
 
Top Bottom