letter never sent
reckoner
It’s a Portside Mini.
Dynavap VapCap
- Thread starter Fenton Mewley
- Start date
It’s a Portside Mini.
Monk Debate
The monks do be debatin’
I’ve heard the coils on those can be rather thick (I have the SJK heater with thinner coils and it takes longer). Here’s what I would do, throw the Dynavap in there empty and time how long it takes to heat up from cold, how long it takes to heat up after the first heat cycle, after the second, etc. Then load some flower in there and heat it up for 1-2 seconds less than the time you measured for the first heat up, see how it tastes. Adjust as necessary. Eventually you’ll just get a sense of how long it takes.
Squiby
Well-Known Member
ataxian
PALE BLUE DOT
I use COLAS of Granddaddy PURPLE in my “M”.
Taste pretty decent actually.
Squiby
Well-Known Member
Yes. You'll be fine. Vapcaps are remarkably resilient and operate just fine with a few orings short of a set.
Last edited:
Hackerman
User
I so much agree. The long and slow heatup of the thin wire SJK coil results in a much smoother, more flavorful hit. I use my Portside Mini at one location and my SJK in another location and they are very very different.
Hippie
Well-Known Member
The M tips take longer to heat than the Ti tips for me with Pipes' IHs
With an M tip I go about 5 seconds past the click on the 1st heat and 3 seconds after on subsequent reheats.
With a Ti tip I go 3 seconds past on the 1st dip and a second after or at the click when reheating.
With an M tip I go about 5 seconds past the click on the 1st heat and 3 seconds after on subsequent reheats.
With a Ti tip I go 3 seconds past on the 1st dip and a second after or at the click when reheating.
ataxian
PALE BLUE DOT
I’m not in a hurry?
The “M” is perfect for me!
Squiby
Well-Known Member
My @Pipes Skelator has always needed a few extra seconds after the click whether I use a Ti tip or a SS M tip. It may have something to do with my batteries or it may be that for faster heat extraction I need to lower the bottom spacer with a bit of sandpaper.
But I'm happy to heat my cap to the click then count one, one hundred, two, one hundred, three, one hundred, four, before pulling it out for the perfect flavorful toke.
Here it is, living in a decorative paint can... Skewed sideways for your viewing pleasure...
But I'm happy to heat my cap to the click then count one, one hundred, two, one hundred, three, one hundred, four, before pulling it out for the perfect flavorful toke.
Here it is, living in a decorative paint can... Skewed sideways for your viewing pleasure...
Moses Baca
Colorado State Reformatory #8755
Wow. With my Flux Deluxe I pull immediately on the very first click, if not even a bit before. If I go 2-3 seconds past the click I'll have combustion. I use Ti and SS Shadow tips.
ataxian
PALE BLUE DOT
I grew CANNABIS COLAS in da 70’s and we just smoked joints?
If I had a ‘M’ walking through field’s of tail’s life would have been easier?
Better late than never?
“M” 2 me is advanced actually!
TI cycles R so cool as R golf club’s!
M=RETRO
-dab8-
Dyna-saur
Like Hacker suggests, I always had to pull out right before the click if I wanted that first amazing flavor hit.Use the 'pull out early' method.
ElPic
Take my money
I Receive my Omni XL today !!
This vape is beautiful and so lightweight, even with the omni condenser and it extra length, it feel lighter than my M. I really love the extra length of the xl too, fit good in my hands. For the performance, not a game changer for me... not for the price of this device vs the M with titanium tips....
Got a question,
I read a lot of people talk about the inability to completely close the carb on the Omni, but is it normal that I can’t completely open it?
Even at the most retract position the condenser is still higher in the tip than on my M ...
First picture is the lowest position vs M regular position. Is it normal that the carb of the omni can’t go as low as the M ??
This vape is beautiful and so lightweight, even with the omni condenser and it extra length, it feel lighter than my M. I really love the extra length of the xl too, fit good in my hands. For the performance, not a game changer for me... not for the price of this device vs the M with titanium tips....
Got a question,
I read a lot of people talk about the inability to completely close the carb on the Omni, but is it normal that I can’t completely open it?
Even at the most retract position the condenser is still higher in the tip than on my M ...
First picture is the lowest position vs M regular position. Is it normal that the carb of the omni can’t go as low as the M ??
stark1
Lonesome Planet
My “W”ee tip is my keeper, with my 7-fin 4th Gen tip. YMMV
2ME an “M” is METRO, like the Red Line squealing to a stop @ Harvard Sq.
YMMV
2ME an “M” is METRO, like the Red Line squealing to a stop @ Harvard Sq.
YMMV
letter never sent
reckoner
Yeah, I'll try this. Makes sense, I would just prefer to not have to think about it too much. My favorite thing about the Omni is how dead simple it is to operate.
That sounds nice. GDP is one of my favorite strains!
I believe that this is because genius george only makes a ss cap. In my IH it doesn't matter which tip I use it will click in 5.5 sec cold and 3.5 sec reheat. Titanium has higher resistance heats beyond what the cap says. When i'm using a titanium tip in the IH I go 4.5 sec and 2.5 sec and ignore cap completely. Works great for me
You're omni is normal. What you have discovered is normal (confirmed by DV). I also didn't realise or expect this when I bought my omni condenser, they are longer than the normal ones so that they can close off the airflow better.I Receive my Omni XL today !!
This vape is beautiful and so lightweight, even with the omni condenser and it extra length, it feel lighter than my M. I really love the extra length of the xl too, fit good in my hands. For the performance, not a game changer for me... not for the price of this device vs the M with titanium tips....
Got a question,
I read a lot of people talk about the inability to completely close the carb on the Omni, but is it normal that I can’t completely open it?
Even at the most retract position the condenser is still higher in the tip than on my M ...
First picture is the lowest position vs M regular position. Is it normal that the carb of the omni can’t go as low as the M ??
Problem for me was i like the airflow wide open always, i only purchased the omni for its strength and simplicity. (No x-rings to move and lose, and just 7 o-rings on my daily driver now, so losing one or two won't stop me)
I ended up sanding mine shorter to regular length. I'll have lost the ability to close/restrict the airflow as much, but that's fine for me.
ElPic
Take my money
Thanks mrb for the clarification , I was wondering if my condenser was too long , but honestly it work fine that way for the moment. The more I use it, the more I like it ... still testing... I got it for 12hrs and i’m at my fifth chamber, and I sleep for 8hrs on that LOL
Still don’t think it worth 2.5x the price of a M, but I do not regret my purchase.
started@52
Well-Known Member
@juanavape
I have one cap that has two clicks, one at least 3 seconds after the first click. Another that has two clicks real fast within about half a second, and another that only clicks once.
I have one cap that has two clicks, one at least 3 seconds after the first click. Another that has two clicks real fast within about half a second, and another that only clicks once.
clusterone
New Member
I'm finding that my Omnivap XL is in a totally different league compared to the 19 M I have. The airflow is just so much better with it. The Karmavap has pretty decent airflow but the 19 M is just lacking. I emailed them yesterday after hearing about the manufacturing issues they had. I have tried emailing them twice in the past like 3 months ago and they never responded, hoping to hear back from them this time around.
StringTheorista
Well-Known Member
The second clicking disc is intentional redundancy. All you need is one click—if you get two it’s a bonus.
Last edited: