stark1

Lonesome Planet
what type of body are you looking for? after months of trial and error i finally perfected making custom wood bodies if you are interested?

here is an example of orange buckeye burl that i did!
iac8OKZ.jpg
[/IMG]
iac8OKZ.jpg
[/IMG]



Dude, your images are AWOL :hmm: Always nice to see people’s crafts.
 

-dab8-

Dyna-saur
Ha ha. I've done this on more occasions than I'd care to admit :dog:



I've used a piece of super-fine mesh screen that I used to use to build wicks out of several years ago when I used to use rebuildable nicotine vaporizers. I cut off a small strip of it and rolled it to fit perfectly inside the Dynavap tip. Put it in the tip, smash a bit of concentrate down on it, put on my cap and heat (leaning the vaporizer back, toward the mouthpiece, when heating so that the oil melts down into the screen). It's worked very well in the two or three times I've used it that way. I even unlolled the plug after I was done, and it was almost perfectly clean. Everything vaporized.

Here's a shitty pic of what I'm talking about:

IMG_0107.jpg
Wow! What is that stuff called and where can I find it? Definitely want to give this a shot.
 

primitiveorganic

Accessory Maker
Accessory Maker
Thank you, I was told to come to this forum, I’m still trying to figure it out!

I edited his post to display the image link.

:peace:

I’m having a terrible time Trying to start my own thread and add photos. I’m new to this forum so please forgive me!

Dude, your images are AWOL :hmm: Always nice to see people’s crafts.

iac8OKZ.jpg
 
Last edited by a moderator:

Ramahs

Fucking Combustion (mostly) Since February 2017
Thank you for your help, Ramahs! I don’t have room for much, but I can fiddle w/ little things like this

Yeah, and a less-fine mesh than I used is might be worth a try. The stainless steel wire mesh I used was something like 400 or 500 mesh.


That is very interesting, thanks for sharing :cheers:

I often don't have access to concentrates other than hash, but do you know where I could get some of that fine mesh? What is it made with?

It's stainless steel, and you can find it on amazon/ebay. I bought a roll of it years ago, and don't remember where I got it. Here's an example of something like what I had:
https://www.amazon.com/WOVEN-STAINL...8038&sr=1-3&keywords=stainless+steel+mesh+400
 
Last edited:

primitiveorganic

Accessory Maker
Accessory Maker
Thank you!

If she truly has an XL condenser (stem + mp) & she wants to swap out the stem & remove the mp for a vong, she'll need to downgrade to a standard condenser. But if she has a standard condenser with body & mp, all she'll need is a vong stem. No?

Would you be interested in a wood VonG body?

xgisy.jpg
 
Last edited by a moderator:

hopla

Well-Known Member
A friend complained that with my little 4" bong he'd sometimes get some water as he'd inhale too hard.
I had an Arizer silicone tube (thought it can always be useful, even if you don't have any Arizer device) and i made my little bong+Dynavap M18 combo safer: here's my chill out sofa solution (maybe i will buy the chinese IH too to make it even lazier and eliminate the butane torch part) :razz:
rc1r7o.jpg
 

Hippie

Well-Known Member
Lots of mesh to choose from for EU peeps here
https://www.wireandstuff.co.uk/products/mesh-wick-p1.html
http://www.vape-atomizer-mesh.com/products/Superfine-Wicking-Mesh.html
https://www.themeshcompany.com/products/Fine-Mesh---0.5mm---0.025mm-Hole-Size.html
(I think they're all the same company)

I haven't done a lot of testing tbh as I only picked up a few sheets for wicking ecigs originally which required finer mesh at the time so I've not tried anything under #200. I find the lower mesh sizes (with bigger holes) performed better so if I were buying again I'd order some below #200 to try too.
I've got an few A5 sheets of #200 mesh to get thru 1st before that happens tho lol
 

Stu

Maconheiro
Staff member
Top Bottom