freeman dyson
Well-Known Member
read the dbv? you mean this thread? and i never stir. i have probably wasted a lot. i am going to start
vape4health
Well-Known Member
I seen the same thing but I didnt think about one being silver and one black but I see the black one running hotter too . ???DR5595 said:
I set my Black DBV at around between 12 and 1 o'clock. Then I slowly increase the temp when I notice the herb is not hitting too hard or I might just breathe in slower at a lower temperature. I tend to just breathe in slower at lower temps because I keep the vaped herb and smoke it.
aero18
vaporist
It doesn't matter what the color of the outer shell is (black or unpainted) in regard to the temperature the unit can reach. Each unit comes with its own dial and corresponding temperatures. The temperatures are not standardized.
The dial can be different on 100 different models. That's why it takes some initial experimentation to work out the particular temperature settings.
The dial can be different on 100 different models. That's why it takes some initial experimentation to work out the particular temperature settings.
max
Out to lunch
The temp range IS standardized. It's the dial settings that aren't, which I'm sure is what you mean. All the units turn on at the same point (only variance would be a slight difference in one temp control vs. another), but the marker on the dial can be sitting anywhere. It could appear that a particular unit is turning on at noon instead of the normal setting of approx. 7. All you have to do is pull the knob off and reposition it so the 'turn on point' is where you want it.aero18 said:
Last edited by a moderator:
Snuff
Well-Known Member
I successfully finished assembling of my new DBV with a small bowl like the PD has. All metal parts are custom made.
Here is what I have got:
Design of a new DBV in the draft:
[URL='http://fuckcombustion.com/threads/best-of-da-buddha-thread.16747/']
[/URL]
Here is what I have got:
Design of a new DBV in the draft:
[URL='http://fuckcombustion.com/threads/best-of-da-buddha-thread.16747/']
[/URL]
Last edited by a moderator:
vape4health
Well-Known Member
I like it too Snuff , good work man .
marbleman65
Well-Known Member
So after I get my DBV to the right operating temp and take a hit or two I often (cause I am mellow at this point) just let the wand with the herb sit in the heater cover without turning the temp down? My question is am I doing harm to the herb? I assume by letting it sit in the heater cover that the herb is getting dried out? Is that the case? Someone said that if I am not toking on it that it doesnt get dried out? That the only heat that passes thru the herb is only when toking? Any thoughts from my fellow vapeheads?
marbleman65
Well-Known Member
I was looking at Dabuddhas website for an attachment for my bong? The prices there are ok, but I then went to my local headshop and for $6 they had a simple 4"x 3/8"glass tube that connects to the whip then into the bong. Very cheap and very effective!! Besides passing along that lil money saving advice my main question is that I find vaping with my bong but instead of putting water in it? I put ice in the tube or in last nights case i packed it with snow!! Very cool looking and cool toking! Does anyone else agree that allowing the vapor to pass thru ice or snow to cool it down gives much more smoother,milkier and more potent hits?
Yesterday the inevitable happened, a first time vaper blew back some bud into the heater! 
I waited for it to cool down, took off the heater cover, then turned it upside-down to remove all the remaining stuff. Now there's a little black mark on the heater. How do I clean it, if it's possible to clean the ceramic part?
I waited for it to cool down, took off the heater cover, then turned it upside-down to remove all the remaining stuff. Now there's a little black mark on the heater. How do I clean it, if it's possible to clean the ceramic part?
DevoTheStrange
Ia! Ia! Vapor Fthagn!
I was wondering about this, I know some people prefer not too have metal in their air path, but wouldn't a screen like the one in the Extreme (Elbow Screen, Dome Shaped) fit into the wand end?wutgwon said:Yesterday the inevitable happened, a first time vaper blew back some bud into the heater!
I am guessing that the whip for this vape is the same size as the elbow piece of the Extreme? if so their little dome screen should fit. This would prevent herb hitting the heating element if accidently blown into.
And you wouldn't have too worry about the screen getting all gunked up because it is positioned before the herb in the air path.
My boss has stopped using his VaporBros whip with his VB, and now uses his spare Extreme whip and cyclone bowl on his VB. The reason behind this is he is tired of herb falling down against the heating part. The Cyclone bowl adds a screen before and holds it away from the HE. So I am working under the assumption that the DBV might use a 18mm piece as well, if so, the dome screen could potentially fit.
now I am not saying that is something that should be done full time, just whenever you have someone over who isn't used too using the DBV. Nice too have the assurance that herb wont be blown into the heating element.
vape4health
Well-Known Member
Anyone have the post that holds the heater get a bit of wiggle to it . The glass and the heater are still moving as one but whatever holds all of it up the bottom of the metal it getting loose , I think it has to do with the 3 screws or whatever them screws go into . Time for some fixin .
Edit : This is not something that just happened , the DBV that I'm talking about took something like a 3000 mile road trip and was being used non-stop , dogs knocking it around and everthing . Something was bound to happen . I'm kinda impressed how it did for that much abuse .
Edit : This is not something that just happened , the DBV that I'm talking about took something like a 3000 mile road trip and was being used non-stop , dogs knocking it around and everthing . Something was bound to happen . I'm kinda impressed how it did for that much abuse .
freeman dyson
Well-Known Member
how often does everyone clean their buddha parts? and how do you smoke kief in it? just sprinkle it in top of other grinded weed?