From what I'm reading here, this device is a sipper and not a ripper. See, I have my SSV with balls and my flowerpot with balls, but I just fancy a nice device to sit and sip at while watching cartoons in the evening.
(Bob's Burgers mostly and I'm torn between this XQ2 and the AVLP or Bowlee.)
Ah nuggets! I might just order one.
Yes, but I fancy something with a big herb chamber to sit n sip on and I always thought logs were a smaller load than the EQ/XQ2 and were heavy hitters. I got my SSV for that.
Yeah XQ2 is what you're after I reckon.Yes, but I fancy something with a big herb chamber to sit n sip on and I always thought logs were a smaller load than the EQ/XQ2 and were heavy hitters. I got my SSV for that.
I'd love something I can load a couple of grams into and sit n sip away on and only have to change the load every night or two. Peak laziness on my part.
that's how I use it most of the time
I may try and engineer something out of a few glass bits.
Wouldn't the old Arizer bowls serve this purpose since the screen is dead center, so still a ways away from the heater, but allows you to pack a bigger bowl?I'm enjoying my xq2. Lots.
Started off at 150*C with the bowl closest to the heater and FULL of a scissor cut up bud of Haze. Very terpy for a good while. I may try down at 130*C to start tomorrow and see what happens.
But yep, cranked up to 170 *C when the terps vanish and then we get cooking all the way up to 200*C.
I managed a fair few episodes of Bob's Burgers with that bowl alone. Whoah... I likey.
Works just as I expected and wanted to.
Ground bud is messy as it falls through the screen and onto the heater cover, I don't remember this happening with the EQ, but then I think that was a mesh screen. ? So the little lab scissors are out and easy peasy to use.
Anyway, my only upgrade/change/gripe about this unit is why not have a further away from the heater AND a bigger chamber bowl? So a bowl with the glass screen in the middle, but then a bit taller so I can load it with a night's worth of dope and just puff away.
There are plenty of aftermarket F/F adapters to experiment with.I'm enjoying my xq2. Lots.
Started off at 150*C with the bowl closest to the heater and FULL of a scissor cut up bud of Haze. Very terpy for a good while. I may try down at 130*C to start tomorrow and see what happens.
But yep, cranked up to 170 *C when the terps vanish and then we get cooking all the way up to 200*C.
I managed a fair few episodes of Bob's Burgers with that bowl alone. Whoah... I likey.
Works just as I expected and wanted to.
Ground bud is messy as it falls through the screen and onto the heater cover, I don't remember this happening with the EQ, but then I think that was a mesh screen. ? So the little lab scissors are out and easy peasy to use.
Anyway, my only upgrade/change/gripe about this unit is why not have a further away from the heater AND a bigger chamber bowl? So a bowl with the glass screen in the middle, but then a bit taller so I can load it with a night's worth of dope and just puff away.
Not a big enough bowl. This one's fine run at lower temps for me closer to the heater.
I wonder if that would work? 4 whips attachment for the swingers parties too! 
From what I'm reading here, this device is a sipper and not a ripper. See, I have my SSV with balls and my flowerpot with balls, but I just fancy a nice device to sit and sip at while watching cartoons in the evening.
(Bob's Burgers mostly and I'm torn between this XQ2 and the AVLP or Bowlee.)
Ah nuggets! I might just order one.
www.instagram.com
arizer.com
My current setup is a very short 18mm F/F adapter, straight (not right angle) whip adapter to about as short a whip as possible, connected to my Orb V2 (wet or dry). Heatsoak at 430F without herb for 10 or 15 minutes, drop the material in, turn on the fan on medium and I can pull absolute clouds.
I liked it at first, but it's an old technology now...you'll get bored because of the cleaning that all the various components require, that's how it was for me. A ball vape is much more convenient in terms of maintenance and being a desktop for me it's essential, nothing to say about the quality of the vapor with a little heat soak you make nice clouds. I want to sell mine,it's been months inside the box
the ceramic rod indeed is old technology but old is not bad. the options here for a ball vape are still limited and quite expensive (there is a rubylizer from katalyzer for 260 euro and the aroma shop versions starting from 300 euro). plus i am not the guy who loves the lungbuster hits. but hey, the future will tell if i still use it after a year. but for now i dig it
Got mine since the first EQ (now the XQ2), I also own 2 ball vapes that gather dust as I really dont see the use, I like to vape with lot of ppl and get super high (I also have pets), a vaporizer with an exposed heating element is a big NO NO for me and I own 2 lamart vapes that can hit as strong as my ball vapes with the same amount (ball vape can hit stronger only because it can use more material) but if I really need a huge rip my XQ2 can do the same as my ball vapes (moding it, pre heating the chamber and using lot of materal). So my friend I see a lot use XQ in your future if you like it today. Also the XQ is one of the easiest vapes to clean I owned., and already had over 15 different vapes but the XQ, V Tower and XQ2 is the only desktop I still use after getting the perfect set for me: stempod SI, Bakx, Tetrax and Sticky Bricks ended my vas. So please enjoy your vape because its awesome!!!! But mod it, you have to mod it. Ddave mod or DIY works great.
Which mod are you talking about?
Probably just a shorter female/female glass oven to reduce the distance between the heater and the herb. Ddave was a proselytizer and seller of them, but you can buy that part from Ali/DHgate/Amazon pretty easily, and the XQ2 comes with a bowl that is more similar to it based on user feedback.
