AirVape Legacy Pro

Deano

Deano

Well-Known Member
I took a few 1/2" stainless mesh screen bowls and covered them with a 16mm screen and it worked incredibly well. The vapor production and flavor was highly improved over the standard capsules.

Of course there's no actual lid but I did take a pair of snips and cut down 2 sides of the mesh filter so I could wrap the screen over top of it slightly.

I was able to use on-demand mode at 370* and blew out large tasty clouds compared to the other capsules needing to be around 415* to produce the same result.
PXL-20230108-185656742.jpg
PXL-20230108-185731763.jpg
PXL-20230108-185803361.jpg
PXL-20230108-185822851.jpg
 
Ariwe

Ariwe

Well-Known Member
Update on the DCs –
I can get single hit extraction with a 1-2 minute pre-heat at max temp. (Its annoying you have to tap the button to cancel the auto shut off...)

streamable.com

IMG_0716

Watch "IMG_0716" on Streamable.
streamable.com streamable.com

Fully roasted:
ibb.co

IMG-0717 hosted at ImgBB

Image IMG-0717 hosted in ImgBB
ibb.co ibb.co

I am going to try a direct draw without the pre-heat next.
 
Ariwe,
Bazinga

Bazinga

Well-Known Member
First I want to thank Airvape for replacing my defective dosing capsules !! They have been wonderful to work with.

While I am waiting for them to arrive, and for grins and giggles, I used needle nose pliers to remove the screen on the top of the capsules. I looked inside the capsule and noticed that there was no seam on the inside circumference that matched the seam on the outside. Inside was as smooth as a baby's tookis. Put in another words, the inside capsule walls were solid (at least to my old eyes). This, it appears, is why the capsules cannot be opened.

I would like to order additional batteries. Any thoughts on these:

LG MH1 INR 18650 3200mAh 3.67V High-Drain 10A Lithium Ion (Li-ion) Unprotected Flat Top Battery $6.25 each.​

 
S

Spin0620

Well-Known Member
Bazinga said:
First I want to thank Airvape for replacing my defective dosing capsules !! They have been wonderful to work with.

While I am waiting for them to arrive, and for grins and giggles, I used needle nose pliers to remove the screen on the top of the capsules. I looked inside the capsule and noticed that there was no seam on the inside circumference that matched the seam on the outside. Inside was as smooth as a baby's tookis. Put in another words, the inside capsule walls were solid (at least to my old eyes). This, it appears, is why the capsules cannot be opened.

I would like to order additional batteries. Any thoughts on these:

LG MH1 INR 18650 3200mAh 3.67V High-Drain 10A Lithium Ion (Li-ion) Unprotected Flat Top Battery $6.25 each.​

Click to expand...
They haven't told me yet if they are gonna send me new ones 🙄
 
Spin0620,
Okla68

Okla68

Well-Known Member
Bazinga said:
First I want to thank Airvape for replacing my defective dosing capsules !! They have been wonderful to work with.

While I am waiting for them to arrive, and for grins and giggles, I used needle nose pliers to remove the screen on the top of the capsules. I looked inside the capsule and noticed that there was no seam on the inside circumference that matched the seam on the outside. Inside was as smooth as a baby's tookis. Put in another words, the inside capsule walls were solid (at least to my old eyes). This, it appears, is why the capsules cannot be opened.

I would like to order additional batteries. Any thoughts on these:

LG MH1 INR 18650 3200mAh 3.67V High-Drain 10A Lithium Ion (Li-ion) Unprotected Flat Top Battery $6.25 each.​

Click to expand...
The Threads on the DC are on the Outside rim of the bottom, not inside !
 
Gary-Airvape

Gary-Airvape

Well-Known Member
Manufacturer
Capsule update!

We finally saw the mistake that the manufacturer made! They put the lid upside down in the bottom part with no screw! That is why it is not opening...

The bottom part has a screw, and the top goes on from the outside, and a little wall should be there to improve the grip.

If you have one, not opening, sorry for the inconvenience; we will replace those!

We did not expect such a mistake between the prototype and mass production...
We apologize for this, and we will make things right!

Best,
 
Last edited:
RxPlorer

RxPlorer

Well-Known Member
Gary-Airvape said:
Capsule update!

We finally saw the mistake that the manufacturer made! They put the lid upside down in the bottom part with no screw! That is why it is not opening... Here are the right ones should look like:

https://www.reddit.com/r/AirVape/comments/w7skmu
c3pekzrfmqd91.jpg
The bottom part has a screw, and the top goes on from the outside, with a flat surface on the top.

If you have one looks like the top part is upside down; sorry for the inconvenience; we will replace those!

We did not expect such a mistake between the prototype and mass production...
We apologize for this, and we will make things right!

Best,
Click to expand...
Thank you @Gary-Airvape! I definitely have the wrong ones with a recessed top and it's very good news that you're responsively replacing them. Thanks for the fantastic customer service!
 
Dr. G

Dr. G

Vapman Collector*Vapman Beta Tester
Gary-Airvape said:
Capsule update!

We finally saw the mistake that the manufacturer made! They put the lid upside down in the bottom part with no screw! That is why it is not opening... Here are the right ones should look like:

https://www.reddit.com/r/AirVape/comments/w7skmu
c3pekzrfmqd91.jpg
The bottom part has a screw, and the top goes on from the outside, with a flat surface on the top.

If you have one looks like the top part is upside down; sorry for the inconvenience; we will replace those!

We did not expect such a mistake between the prototype and mass production...
We apologize for this, and we will make things right!

Best,
Click to expand...
Wow...even I have the wrong ones. So, how are you going to do this?
 
TigoleBitties

TigoleBitties

Big and Bouncy
Gary-Airvape said:
Capsule update!

We finally saw the mistake that the manufacturer made! They put the lid upside down in the bottom part with no screw! That is why it is not opening... Here are the right ones should look like:

https://www.reddit.com/r/AirVape/comments/w7skmu
c3pekzrfmqd91.jpg
The bottom part has a screw, and the top goes on from the outside, with a flat surface on the top.

If you have one looks like the top part is upside down; sorry for the inconvenience; we will replace those!

We did not expect such a mistake between the prototype and mass production...
We apologize for this, and we will make things right!

Best,
Click to expand...
Well I guess this explains why the DC volume seems smaller than it should be. Is the microdosing wheel necessary when using the capsules?
 
OrsonWhales

OrsonWhales

Well-Known Member
MedMJ22 said:
I can still get plenty of vapor with the dosing capsules at 340-360F. I don’t notice a change in flavor either. It’s the same material as the existing bowl and the microdosing disc functioned similarly to the lid. A completely packed bowl should be no different than a packed capsule. The materials are the same and the contact points are the same. I think there’s a lot of negative placebo going on.

On another note, another vendor is selling dimpled glass airway replacements with and without rubies that fit the ALP. It’s already very cool, but may be worth a try.
Click to expand...
What vendor?
 
Deano

Deano

Well-Known Member
MedMJ22 said:
I can still get plenty of vapor with the dosing capsules at 340-360F. I don’t notice a change in flavor either. It’s the same material as the existing bowl and the microdosing disc functioned similarly to the lid. A completely packed bowl should be no different than a packed capsule. The materials are the same and the contact points are the same. I think there’s a lot of negative placebo going on.

On another note, another vendor is selling dimpled glass airway replacements with and without rubies that fit the ALP. It’s already very cool, but may be worth a try.
Click to expand...
An additional bowl is basically being added which absorbs a lot of the heat itself.

There is a notable difference with and without the DC in terms of vapor quality, production, and the temps that perform.

On-demand mode at lower temps (350-370) is where I've witnessed this the most.
 
F

felvapes

Well-Known Member
Yea very disappointed with the dosing caps
I only use it in on demand at full temp, and the loss in performance is night and day
The floor and lid need to have mesh screen with the solid walls they have now against the oven walls to create the air tunnel (in particular the bottom needs to be more open to let the hot air in and flow over the weed) - I mentioned this when they were designing them
Even a more open cross/hatch style would be better than the current design
This would give us better airflow and performance + clouds

Tastes nice but the vapour production and performance is lacking big time in comparison to without caps
 
K

kapows

Well-Known Member
Dr. G said:
Greetings, I think they are speaking about VGOODIES...because I purchased the ruby tubes last week. I am allowed to say that? I am not sure I will get in trouble. I am sorry if so.
Click to expand...
Pretty sure its fine. Got a pic and hows it perform?
 
kapows,
vandalizedbythelotus

vandalizedbythelotus

Well-Known Member
Gary-Airvape said:
Sorry, the wall has been raised, so not the flat surface is the right way, the fact that it's not open is!
Please email your order number and a picture of the wrong capsule to cs@airvapeusa.com.
Click to expand...
seems to me the raised wall is restricting airflow considering it closes the gap around the microdosing disk. possibly impairing the side orifices in the disk as well.
 
vandalizedbythelotus,
MrBaked.co

MrBaked.co

Well-Known Member
Recommended vape supplies also sells the different tubes for the airvape.
They are based in the UK. I bought the a tube with Ruby balls in it when I got my vape from them..

I've never actually used the device as standard..
 
MrBaked.co,
You must log in or register to reply here.
Top Bottom