710 coils

710Coils

Well-Known Member
Manufacturer
@Kanna_Kult I want to carry the Ruby pearls and am just waiting for China to let me know when I can purchase them. The inserts are still a bit out as the polish is not where I want it. They work great, just dont have that perfect transparent look yet and so I wont carry them until they are exactly as expected =)

Got some sweet pearl tools in and will be adding them to the site today.
thumbnail
 

LongDraw

Well-Known Member
hey shane, sorry to bother. any eta on the coils for when they are coming in? No real rush, i have my other set up, but the rdk300 just came in today so it got me antsy. haha.

regardless, can't wait to use your enail stuffs, they look awesome.
 

tepictoton

Well-Known Member
I do the same with 25mm opaque

However, this might clean the 'dish area', I find I still need to clean the neck and joint from time to time. That's when I throw it in a ceramic cup with boiling water, and after a minute take it out with gloves and add a bit of alcohol in the joint to shake loose and or dissolve the last bits stuck.

Sometimes I am happy with 'just' that. Sometimes I take out old torchy and make her all glowy and red:D

Please do not 'throw' your banger too hard in the ceramic:p
 

710Coils

Well-Known Member
Manufacturer
So temps and cleaning.......


Coils only real weakness is prolonged heat above 700 degrees for 5 minutes or more. This is due to the little wires and the heat created from going above 700 degrees. I personally recommend doing the 250 degree set temp and use distilled water or dark crystal. The other option is the simple green tech and both of those techniques will work great without causing undue strain to the coil.

One thing to note. The above could take a year to finally fail as its the weakening of the integrity of the wires

Hope everyone is having a great Friday =)

Your ever loyal coil and quartz monger


Shane
 

JCat

Well-Known Member
Accessory Maker
I assume when you use the baking soda you mix it with a little water to make a paste? Or are you just using it dry?
Yes.
- I first rinse my banger under hot water
- Then I soak in my jar of 99% ISO for a few minutes if I have other stuff to clean (otherwise might just use a pipe cleaner and/or q-tip to speed the process of getting the sticky stuff out).
- Next, rinse again under hot water, dump out all water, and dump in a little baking soda (maybe 1/2 tsp or so)
- Take a small piece of paper towel, soak, and ring out, then use to scrub around inside of banger with finger
- Can also use same piece of paper towel to wipe out ruby/sapphire insert and pearls quickly
- Rinse in hot water, ISO rinse, then rinse again in hot water.

That's it. Whole process takes maybe 5 min and everything always looks 100% new like the day I bought it.
 

twoleftfeet

Well-Known Member
So temps and cleaning.......


Coils only real weakness is prolonged heat above 700 degrees for 5 minutes or more. This is due to the little wires and the heat created from going above 700 degrees. I personally recommend doing the 250 degree set temp and use distilled water or dark crystal. The other option is the simple green tech and both of those techniques will work great without causing undue strain to the coil.

One thing to note. The above could take a year to finally fail as its the weakening of the integrity of the wires

Hope everyone is having a great Friday =)

Your ever loyal coil and quartz monger


Shane

Good to know, ive ran a few 800° cycles but Ill stop. I dont want to have to replace the coil if i dont have too. My simple green concentrate is on its way
 

add1noob

Well-Known Member
OK boys i fucked up today. My coil seems to have cracked the banger when cooling down im not sure how it got tight enough to do that but im guessing i must have done it when i cleaned the banger last. Any preventative tips to stop this in the future? also how can i loosen up this coil or should i just get another?

Edit: I just slapped the coil on my spare banger and it fits with some wiggle so my current theory is that my last banger was slowly growing or that this one will possibly break when im done smoking.
 
Last edited:
add1noob,
  • Like
Reactions: 710Coils

add1noob

Well-Known Member
@add1noob That sucks and was most likely one spot that was just a smidge too snug. The looser banger should be fine and I can give you a discount on a replacement banger =)
No worries you've absolutely changed the way I smoke with your products to the point where it feels like i owe you. Ill probably order an extra from you soon, keep up the great work!
 
Top Bottom