Search results

Yes to the first. YES to the second. I’ll put half-ish of that amount in the chamber. (2021 harvest, super sticky). Low heat. Then crush it and reload for a second cycle. The thermal lag is laggy. The hit is worth a wait. I think we will see a few more Editions in the future.

I watched the interview. I learned that twisting would change the airflow adjustment. I tried it. I’m not sure if it works better when it’s warm or cold. Because it’s warm now and I’m a little confused.

More Lighter ranting. https://ultracool.ca/nuflame/ I used to use a UF-4975 constantly for my previous butane devices until the ignition stopped working. With my Anvil, I’ve been using a UF-4976 almost exclusively. I have used an imitation Pencil Torch as a backup. I prefer the wider, softer...

Are you packing the oven or the little chamber? How fine is your grind? Looking down the oven you see the condenser stem with the screen in it. There is an air gap around it. It has to stay clean.

Was this heat up shortly after a previous heat up? The battery holds heat from before. Then it gets slightly overheated by the time the clicker clicks.

I just got mine today. Gas leaks. Blew flames all over my hand.

To celebrate my three week anniversary with my Anvil, I hit the large bowl three ways. First, I put a light sprinkling of loose flower and heated it to a medium low. Very airy, felt hotter, direct to lung. Wow. That was a fast high hit. Second, small nug. Grabbed my mason jar bong because the...

“So my question: can you low-dose happily with the full bowl or is the half-bowl clearly superior? I've seen the posts that say it's possible, but I'd like to know how well. For ex, can you load less in the full chamber or hit a full load over multiple sessions “ I’ve been using the half...

A dyna is conduction first. The Anvil is convection first. Completely different operating systems. And the anvil slammed me so much harder and differently that it’s taken a couple of weeks to change my dosing and feel normal again.

I’ve been enjoying a wide flame. I find a focused flame gives me too dark of a cook. Regarding the Ronson specifically, if “flame lock” means it stays lit without holding, then no. It has to be held to stay on.

For lighters. I’m in Canada. I’m very happy with this odd looking torch. It has a large, adjustable flame. It holds enough fuel for about 30 heat cycles (three days). I went to two stores today to purchase backup spares. Store inventory is wrong. I just ordered two online. Hopefully they will...

Three coils. Each one lined up to the batteries. Then tune the heating cycle. Charge the low batteries for a bit. Then the body. Then the low batteries. Then the body. Then the top battery to get the thing to click already.

An induction coil, single loop. Pass through charging on usb connector. That might be my wish list.

Back to induction heaters! I used my wand as much as I could today. The heating is too evenly spread across the device. I cannot select and pinpoint my heat at the three different copper batteries. The body of the anvil heats up too much too. Unnecessarily. It’s really punishing the wand. It...

When I first got my anvil I tried it in my Wand and it clicked but it was really wispy. So I wrote it off. I WAS WRONG!!! I just tried it with a freshly charged Wand and it worked. When I first tried it, my batteries were probably too low. And I had a silicone cup installed in it. I removed the...

I WAS WRONG!!! I just tried it with a freshly charged Wand and it worked. When I first tried it my batteries were probably too low. Post in thread 'Anvil by Vestratto' https://fuckcombustion.com/threads/anvil-by-vestratto.51804/post-1634205

I use finger trimmed nugs. Medium heat. Once cooled, crush the nug and put it back in. Medium heat. After those two cycles, toss. The vapour is still very strong on the second cycle. There’s not much left for a third cycle. Riding the line is scary enough. And it not to my flavour. Helix...

Got my User’s Edition. Writing this while the packaging isn’t in the garbage yet and my first hit is kicking in. Ispire wand does not work on the new ovens. I haven’t only heated the top copper ring and I’m already hammered. Anvilled or whatever. Wow. Convection is different.

#11xx. I got in on the now named User Edition first release.

I just got my tracking number!!!