Search results

DIY! :science:

. I don't use a honeybee, so I'm not familiar with the capacity. I use a copper pipe about 13" long by 3/4" ID. With about 4-5 screens in one end. I prefer a smaller diameter tube to avoid "dry" spots. My last run was 7g and I got 1.3 from the first blast and .4 from the second. I do unplug...

If the Omicron has a "HVD" and number on the top opposite the button than it can be used at 7.4v with The Core. Some have had success with 3.7v and the Herc but I use it with 7.4v. @Mynameismud may have some more insight on Hercules with 3.7v.

Do not be intimidated by this process just be SAFE. ALWAYS do butane extractions outdoors. Keep any potential source of spark away from the process. I have a fan blowing on the area I extract in from about 20 feet away to keep the fan motor away from I the process but still get air flow. I...

I'm not sure what fits in the KISS but .5mm is pretty thick, about 1/2 the thickness of a dime. I ordered the 32 gauge wire based on I the resistance per foot. Look at kidneypuncher.com there is a lot of info about the wire including sizes and resistance and metal content. I found a site...

@redglassgallery : I am loving the look and function video of your 13" v2 rocket piece on ioffer.

Flashing red/green indicates that it is just in between and ready to turn green steady.:nod:

Many thanks to @THCscientific for handling my ticket issue. :clap: Also, I received my Hammer top today after waiting for the USPS. (Was shipped on 2/19 2 Day). The Bender is much easier to use with this beauty.

What kind of wire was used in this repair. Is the resistance the same ~1.0 Ohm? Does this wire heat along the entire length (even going thru the white grommet)? Thus transferring heat into the top?

Spares are good :nod:!

Not sure I understand. The dry ice cools before butane evaporates? I get the funnel and paper filter, I just don't get where the dry ice comes in.

I am not familiar with that mechanical method. How does that work?

To answer about the KISS. You can get a few good hits from a small amount loaded at a time. Think a ball the size of a BB. It is forgiving of all types of concentrate but the "dirtier" it is the more crusty the coil will get. You should also look into getting a Hercules SR-74. There is a...

Do you purge with heat and vacuum? Does the purge change the consistency? I have been thinking about getting a vac setup.

My last run was 1.7 out of 7g. I always grind(coarse like for rolling) for first run then run 1 can of 5x. Then remove and grind again much finer but not powder. Then run another can. I blast into Pyrex floating in a electric skillet full of water (120 degree). First run tastes amazing. Second...

Utopia Planitia=UP Tech is a manufacturer. There is a thread here for each Persei and Omicron. Those are the two most popular. Their manufacturer presence here is @THC SCIENTIFIC.

Decants like a BOSS...!:rofl:

I am consoling myself on the death of my 7.4v KISS with my new best friend that the postman brought today. :rockon:

Many cycles of heating and cooling will cause metal fatigue which creates weak spots in the metal and it becomes very brittle and breaks. I have been very careful with mine to not let it glow dry and very careful when loading. I didn't even use this last one enough to need cleaning yet:(.

Well, my 7.4v Ti KISS died today. :cry: It didn't really get too much use because my driver is the Omicron w/3.7v KISS. Probably less than .5 thru that one but my 3.7 is a different story. Probably at least 2g through each, the Ti and standard version. @THC SCIENTIFIC I need Triton!