-
SCAM WARNING! See how this scam works in Classifieds.
TinyMight / TM 2
- Thread starter kuzko
- Start date
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Should be about an inch
Cheebsy
Fermentation Fiend
Thanks man, I could really do with an accurate measurement though, preferably in mm if at all possible.
XoGnosis
Member
my cheap calipers being operated by an untrained and highly medicated hand says 30.70mmThanks man, I could really do with an accurate measurement though, preferably in mm if at all possible.
edited to add that this is a walnut tm2 purchased around 4/20 of this year with the factory ring finger tight.
Cheebsy
Fermentation Fiend
Absolutely perfect! Thanks very much mate.
gangababa
Well-Known Member
Measured with my caliper depth stop. From the boss at the bottom of the oven sleeve (the stem stop) to the top of the adjustment ring is 31 mm.
Keep in mind that the adjustment ring may vary (tighter, less tight). Measured from stem stop to top without the ring it is 29 mm.
All on my fairly new walnut wood unit; others may vary.
Cheebsy
Fermentation Fiend
Absolutely man. Thanks for your assistance.
ginolicious
Well-Known Member
The time has come for me to finally order a Tinymight 2. Will be doing so in the next couple of weeks. I just cannot decide if I get dosing capsules as well with my order. Not sure if I will really need them or not.
Petetbay
Well-Known Member
Good to see you’re getting TM2. About the caps that’s a personal choice some people like them for easy loading when out and about, others like they run cleaner than without. I used to be a big cap user, but my ability to load them has become difficult due my digits and now only use them only for hash. They work ok for herb with TM2 with slightly more conduction effect and the load is used up quicker. I prefer the non-capped TM2 herb load and don’t think they are a necessity for the TM2 unless you’re using hash or hash/herb mix.
Indifferent FIsh
Well-Known Member
There are rumors of an all black edition coming out soon, so you might wanna pump the brakes on grabbing a TM2 monetarily.
jbm
Well-Known Member
Which will also incorporate as yet unnamed “functional upgrades,” which, if past practice holds true, will only be available in the all black model.
ginolicious
Well-Known Member
This was something I was worried about. A new model coming out. I guess I gotta wait a bit longer then to see how this unfolds. Firefly 2+ is gonna have to tide me over.
When you all clean your mouthpiece are you tossing it all in ISO? Doesn’t the cooling unit have gaskets on it? And are those safe for ISO? If not, how are you all cleaning the gasket? I was under the impression it could be dropped in ISO.
When you all clean your mouthpiece are you tossing it all in ISO? Doesn’t the cooling unit have gaskets on it? And are those safe for ISO? If not, how are you all cleaning the gasket? I was under the impression it could be dropped in ISO.
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Get alternative aftermarket stems instead
Indifferent FIsh
Well-Known Member
Or get some 3mm boro, quartz, whatever balls and load them in your stem between two basket screens! Quick and easy aftermarket stem right there
Shit Snacks
Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Or get some 3mm boro, quartz, whatever balls and load them in your stem between two basket screens! Quick and easy aftermarket stem right there
I found 3 mm to be too small, but a mix of 4 mm and 6 mm can work well, I find that tedious with extra screens though, and much prefer the stems with the balls fixed, but even more than that I prefer u-turn stems or hooks the most, haven't used stock in years
Cheebsy
Fermentation Fiend
When I was using the stock setup I would always clean the o rings in the same way as the rest of the stem. You sometimes see them stretch or deform if they soak for hours, but when they dry off properly they return to normal shape IME.
If you go with balls and screens if you make sure the screens are well formed and fit tightly you can soak the lot without disassembling.
Aftermarket stems are much nicer though and something you should aim for eventually. If finances are tight the stock setup, or balls in stock stem will work fine until your wallet recovers.
Pib
Well-Known Member
Doesn't the current TM2 come with the short stem with the cooling unit and the short ball stem? The ball stem cools quite well for the time being and you can look around in peace. And the problem with the seals is also rather marginal with the ball stem, they are only on the removable mouthpiece.