Da Buddha

vapurrize · Sunday at 11:47 AM

After so many years why did 7th floor never release the 4 element/ 4 whip / quad heatsink cover party budha "vapo monastery" this would be a 400$ thingy basically 4 buddhas in one unit and it'd cost like 20$ more to produce heck make it a 5 6 or 7 element buddha so many knobs to play with it could be a 3 knob thing (1 knob single element and the other 2 would turn on 2 more elements or 4 more so with binary setup you can turn on from 1 to 7 with only 3 knobs ) and when people start breaking the glass they would get huge 300$ orders for a few nice wand, a few feet of tubing, bubblers and what not

Pukka · Sunday at 1:36 PM

There was a really old double element VaporBrothers VB1 san's element covers (but with an indication even though they don't usually repair units that old they would for this one) on eBay for 4-500 usd. Unfortunately too rich for me.

The issue that comes up with multiple elements is total amp draw of the device. It'd be like trying to run the microwave, toaster oven and fridge off the same wall outlet at the same time ;-{>====

coolbreeze · Sunday at 1:49 PM

vapurrize said:
After so many years why did 7th floor never release the 4 element/ 4 whip / quad heatsink cover party budha "vapo monastery" this would be a 400$ thingy basically 4 buddhas in one unit and it'd cost like 20$ more to produce heck make it a 5 6 or 7 element buddha so many knobs to play with it could be a 3 knob thing (1 knob single element and the other 2 would turn on 2 more elements or 4 more so with binary setup you can turn on from 1 to 7 with only 3 knobs ) and when people start breaking the glass they would get huge 300$ orders for a few nice wand, a few feet of tubing, bubblers and what not

This is a totally different take on achieving something similar: Get one of these 4-way whip adapters:

and one of these hydratower bases:

and plug your Baller Buddha into it. Should keep up fine, just require frequent reloads.

Radwin Bodnic · Sunday at 2:35 PM

coolbreeze said:
This is a totally different take on achieving something similar: Get one of these 4-way whip adapters:

and one of these hydratower bases:

and plug your Baller Buddha into it. Should keep up fine, just require frequent reloads.

Wouldn't it require to plug others mouthpieces when drawing ? Otherwise you might just draw air from them...

coolbreeze · Sunday at 2:58 PM

Radwin Bodnic said:
Wouldn't it require to plug others mouthpieces when drawing ? Otherwise you might just draw air from them...

Yeah, I'd put mouthpieces on them or corks if there are fewer than four people. Use the hydrabase for cooling instead of individual pipes. So out of the DBV, into the hydrabase, out to mouthpieces on the hoses.

Vitolo · Sunday at 6:53 PM

coolbreeze said:
Get one of these 4-way whip adapters:

I still use my Vapir Rise, and keep it very near my Da Buddha.
The Rise fills bags, or acts as a whip vape... and also comes with a 4 way top piece...
Each vapor port has it's own separate shut off valve.

It does not get used as often as my DBV, but it's very novel.

Cruiser · Sunday at 7:12 PM

coolbreeze said:
Yeah, I'd put mouthpieces on them or corks if there are fewer than four people. Use the hydrabase for cooling instead of individual pipes. So out of the DBV, into the hydrabase, out to mouthpieces on the hoses.

Elev8 sells one-way valves to solve this problem too. 14mm direct to 3/8” ID whip hose. Search for Hookarizer to see their multi-output piece to go with them. Or you can (could?) get them cheap on AliExpress - one-way hookah valves. It’s a marble, place for it to set, and a pinch in the glass that only lets air flow one way. I use them all the time with a splitter on a GooRoo HD3 when there are two or more. Get extras, as they get sticky after a half-dozen or so bowls and need a spray of alcohol and a moment to dry.

Best part is everyone gets their own mouthpiece. So no sharing wet ones. : ). And no passing anything, which cuts down on breakage. They do restrict airflow a little, so not the best for ripping a whole bowl. But for sharing a session, they’re great.

vapurrize · Sunday at 7:57 PM

Pukka said:
The issue that comes up with multiple elements is total amp draw of the device. It'd be like trying to run the microwave, toaster oven and fridge off the same wall outlet at the same time ;-{>====

yeah the design Im thinking of would have different chambers for each element so the multiple elemetn would make it heat up faster... you're right ... probably I'd plug that in my office and notice the PC and vape have the breakers go off

Cruiser said:
Best part is everyone gets their own mouthpiece. So no sharing wet ones. : ). And no passing anything, which cuts down on breakage. They do restrict airflow a little, so not the best for ripping a whole bowl. But for sharing a session, they’re great.

thats the main point... Thanks for pointing out the hooka valve thing. I will look for it. having a Single bucket can be nice too since most people cant bother to stirr and all if they are new to vaping

Da Buddha

vapurrize

Well-Known Member

Pukka

Well-Known Member

coolbreeze

Well-Known Member

Radwin Bodnic

Well-Known Member

coolbreeze

Well-Known Member

Vitolo

Vaporist

Cruiser

Member

vapurrize

Well-Known Member