Arizer Solo

Elephantman562

Elephantman562

Member
Thank you of for the helpful info .
OF said:
Where are you located? If in the US, PM me your address, I should be able to find a few rings for you, I've got a bag of each size somewhere and loose ones spread around.

I'd avoid materials not known safe at full temperature, other materials are likely to 'out gas' something nasty you don't want. The recommended rings are known 'food safe' to 260C. While they don't normally happen in hardware stores (they make lousy seals for plumbing compared to Buna and are expensive) but you can often get them from hydraulic or automotive supply shops.

If my notes are right you want size 113 for older model Solos, 015 for newer ones. The key feature being 9/16 inch ID. However, there's a real limit to how much tighter they make it (that's not the intent of the ring in the first place) and must be carefully fitted or you'll end up breaking the tabs on the bottom and it'll come apart on you.

So, where are you located?

OF
Click to expand...

Thanks of for the valuable info. And im in los angeles with a newer solo btw .. So when i install the seal the added pressure of the cap to case of the solo just literally crumbles the bottom ? Dang i had no clue thanks guys . and i was using my homemade o ring and its fine but i have no doubt it will deteriorate soon so i removed it at the expense of added air i really want a nice tight hit and unfornately the only thing tight is money at the moment so i use innovation on any obstacle encountered lol. i actually love some restriction it allows me to pull a better vape. Also i made a nice stem cap with sugru so thats cool.
 
lookhigh

lookhigh

FC member
nondarb said:
New to the solo world. Just got mine in today, still charging :( . Only an hour to go on the initial overcharge. I'm inpatient as all hell, but after reading a zillion or so pages of this thread I reckon it'll be worth it.

So far I've already lightly swabbed the bowl and stems with ISO and plan to do 2 or so full cycle burnoffs, anything else to do right off the bat? I've got some organic cotton to mess with after I get my training wheels.

I noticed my bent stems filter holes are nearly 2x the size of my strait stems, I kind of wish it were the other way around as I'm sure I'll prefer a less restrictive airway and the bent stem seems difficult to clean. We will see! This is my first "serious" type entry into the vaporizing world, the wealth of information on this thread and website as a whole helped me make my decision. Already got a d020 and some other goodies on the way!!
Click to expand...
Welcome to the SOLO/fun.
Looks like you are set for launch. No need to complicate things yet with accessories etc until you get more familiar with your shiny new SOLO.
 
lazylathe

lazylathe

Almost there...
I gave my Solo away a few weeks ago to a friend to try and stop her from combusting.

Found one for $60, no stems though but the latest version!

@biohacker has been taking a hit in the testing department and has been having major success!!

Following in that stead I have been using the Solo on 7 with a PVHES and only less than 0,1g per load! Heat soak for 30 seconds or so and hit!
Instant dense vapor that still has awesome flavor!!

What astounds me is the effects that I am getting from the Solo!! Successfully medicated off about a 1/4 of my usual load size!!
ABV comes out nice and dark and even.

The Solo has become my daily driver almost instantly!
Affordable and super simple!!
 
OF

OF

Well-Known Member
sloth said:
Does amazon have any thing that can be used a travel cap for the stems?
Click to expand...

In a pinch, these should work:
http://www.amazon.com/gp/product/B004672ZS8?keywords=vinyl caps 1/2 inch&qid=1445784468&ref_=sr_1_12&sr=8-12

They're the right size, you really want '1/2 inch ID Vinyl caps', which you can also get at larger hardware stores.

Us them cold only, of course, unless you buy high temperature ones (like from McMaster Carr).

puddleglum said:
Lately I have been using temp 7 but inserting the stem only when I am actually taking a hit, then quickly removing it (with the unit inverted so as not to spill). This seems to give me a great flavor, like I would associate with convection. Does anyone else use their Solo like that?
Click to expand...

I tried that early on, too much work IMO. Got in the way of enjoying the sipping? Perhaps useful for others, but 'doesn't fit my pistol'.

OF
 
nondarb

nondarb

.
lookhigh said:
Welcome to the SOLO/fun.
Looks like you are set for launch. No need to complicate things yet with accessories etc until you get more familiar with your shiny new SOLO.
Click to expand...
Thanks, I've got 2 weeks or so to play with it waiting with the bubbler :) .

I do need some advice however, I've ran 5 stems or so so far and haven't really produced many if any "clouds" at all comparable to smoke. Granted I've been taking the slow route mostly: starting at 2-3 for a tasty hit or so and working my way up. I've gotten a nice buzz, but still nothing like combusting. Any tips? I've already tried a bowl or so starting at 4, but it didn't really help with vapor production, just sped up the whole process.
 
ataxian

ataxian

PALE BLUE DOT
nondarb said:
Thanks, I've got 2 weeks or so to play with it waiting with the bubbler :) .

I do need some advice however, I've ran 5 stems or so so far and haven't really produced many if any "clouds" at all comparable to smoke. Granted I've been taking the slow route mostly: starting at 2-3 for a tasty hit or so and working my way up. I've gotten a nice buzz, but still nothing like combusting. Any tips? I've already tried a bowl or so starting at 4, but it didn't really help with vapor production, just sped up the whole process.
Click to expand...
Other's have their preferences!

Find what works for you!

I use level 4 with water.
Level 4 with a PHVES.
Level 5 with a VORTEX.
I have a old SOLO that refuses to die?

I liked smoking joints better however I cough too much!
 
Last edited:
lazylathe

lazylathe

Almost there...
nondarb said:
Thanks, I've got 2 weeks or so to play with it waiting with the bubbler :) .

I do need some advice however, I've ran 5 stems or so so far and haven't really produced many if any "clouds" at all comparable to smoke. Granted I've been taking the slow route mostly: starting at 2-3 for a tasty hit or so and working my way up. I've gotten a nice buzz, but still nothing like combusting. Any tips? I've already tried a bowl or so starting at 4, but it didn't really help with vapor production, just sped up the whole process.
Click to expand...

Everyone has their own preferences when using a vape.
With my 1st Solo i used mainly level 4 dry with the bent stem. Great flavour and decent clouds.

Now with my second Solo this is my routine:
Heat Solo up to level 7, i just leave the cap on and heat.
Load up my PVHES GonG with usually less than 0,1g and lightly tamp it down.
When Solo is up to temp i place the GonG inside the Solo and wait 45 seconds.
Invert onto my WT and hit!
Almost instant thick vapour and amazing flavour!
I usually get 3 very good hits from that load and will get about 5+ smaller clouds until the load is spent.

One important factor is the quality of the material you are loading!
My OG Kush makes vapor so thick it chokes me, while my Green Crack just white walls with ease and then i have some stuff from a guy at work that produces very little vapour but does give a nice buzz for a while.

And remember a preheat for the herb is where it is at with the Solo!
 
B

biohacker

Well-Known Member
This is what I was talking about earlier with the one hole on my Solo. It's not blocked by debris or anything, this is just how it came. I'm pretty sure I remember the same thing in past Solo's...is it the norm? It's as if the bottom plate portion is shifted? But why then are the other 3 holes visibly open? There is a hole on the side still so there is airflow and the Solo functions great from what i've seen so far. Intentional design?

newest M1H model...even came with stem caps and a stir tool (like the Air).

SdtjKuk.jpg
 
Pipes

Pipes

Addicted DIY Enthusiast
Accessory Maker
To me, that looks like some excess of the furnace type cement. The manufacturer use to seal the wires going into the heater and thermocouple. If you poke it with a pin, my guess it will chip off. Then it will be stuck in the under portion but should work it's way to freedom down the road.
IMHO, nothing to be overly concerned about.
 
B

biohacker

Well-Known Member
Thanks, I know it's difficult to see in the pic, but there is a distinct round outer edge to it, so I don't think it's cement. There is also noticeable space on the side of it for airflow. I'm talking about the lower left, the lower right is normal, it's the same as the above just doesnt look like it in the pic.
 
Pipes

Pipes

Addicted DIY Enthusiast
Accessory Maker
Is it the white looking stuff? I searched for a picture but couldn't find. There is a white paste they use which dries into a cement type compound. Chips like a plaster. There has been previous concerns about the powder it crumbles into when touched.
There is nothing else I can think of in the realm of normal. Than again, really hard to see from here..lol

OK In really looking close, that hole does look slightly smaller. Like not cut all the way to the side wall...? Is that it? If the case, then yes some air flow will be loss. But hard to say what difference to expect. Would not think anything to worry about.
If bugs you, I'd go for a large pin or dart to give a poke. I used a dart in mine to poke into the holes to clear and even enlarged a bit. Not recommended if you plan to return for warranty though.
 
Last edited:
ataxian

ataxian

PALE BLUE DOT
biohacker said:
Thanks, I know it's difficult to see in the pic, but there is a distinct round outer edge to it, so I don't think it's cement. There is also noticeable space on the side of it for airflow. I'm talking about the lower left, the lower right is normal, it's the same as the above just doesnt look like it in the pic.
Click to expand...
When I had the VRIP kit with the Bong style water pipe I couldn't handle it?

Joints rolled with Zig Zag paper is the best.
Now days smaller mouth pieces are more desirable.

I remember when Bob Marley became famous.
Some of my surf buddies used Bong's while I stayed with joints!
 
CarolKing

CarolKing

Singer of songs and a vapor connoisseur
Solo to the rescue last night with a lot of pain and anxiety needed the convenience of the Solo. It's small and portable and comes in handy when having a difficult night.

I had gone shopping to the cannabis farmers market and bought some great meds. It's harvest time in the Pacific NW. I bought some Matanuska Thunderfuck (among some other awesome strains) and it put me out like a light.:zzz::leaf:
 
sloth

sloth

Well-Known Member
OF said:
In a pinch, these should work:
http://www.amazon.com/gp/product/B004672ZS8?keywords=vinyl caps 1/2 inch&qid=1445784468&ref_=sr_1_12&sr=8-12

They're the right size, you really want '1/2 inch ID Vinyl caps', which you can also get at larger hardware stores.

Us them cold only, of course, unless you buy high temperature ones (like from McMaster Carr).



I tried that early on, too much work IMO. Got in the way of enjoying the sipping? Perhaps useful for others, but 'doesn't fit my pistol'.

OF
Click to expand...
Thanks for the link. After a little more searching I found these http://www.amazon.com/Shepherd-Hardware-9205-2-Inch-Hi-Vinyl/dp/B000BQWKEM/ref=sr_1_9?ie=UTF8&qid=1445829977&sr=8-9&keywords=1/2+rubber++vinyl it says theyre vinyl and that they have "Greater heat resistance than rubber leg tips." Is there any reason why they wouldn't work?
 
OF

OF

Well-Known Member
sloth said:
Is there any reason why they wouldn't work?
Click to expand...

They might work. Vinyl leg ends tend to be very stiff (for wear resistance), more so than rubber the same size (which often have thicker (molded) 'tops' (or bottoms installed). The stem needs to stretch it out to .56 or so, that could be a tough stretch with vinyl, more so than rubber?

Tube caps, OTOH, are thinner and intended to stretch more since the sizes 'overlap'.

One easy way to find out for sure........

OF

Edit: Notice the half inch size is intended to also cover 9/16 (close to the actual size of the stem), indeed up to 5/8 inch?
http://www.mcmaster.com/#vinyl-tube-caps/=zj2lhz

OF
 
Last edited:
You must log in or register to reply here.
Top Bottom