Induction Heater Yllvape IH Power and temperature controlled induction for use with Dynavap

Manako_

Member
Isn’t it more likely that the YLL is not meant to be used with an Anvil due to its greater metal mass than a “defective” device?
Here there has been talk of using it with the Anvil and no one mentioned that it got hot, I know it is not its initial use, but I have also mentioned that it gets hot with the Vapcap without getting the message out, I am just asking if it is normal.
I'm sure I didn't approach the question correctly, sorry.
 

fogbank

Well-Known Member
For those of you who use it with the Anvil, does the IH get too hot? With only three cycles it is very hot and I get a message "Cooling Time" and I don't know if it's a problem with my unit that is defective, with vapcap it also heats up but I don't get the message
I have used the Anvil with the YLL Induction Heater many times. I don't recall seeing that error message. I use power mode and I heat the Anvil for 15 second cycles (watching the timer in the display). After the Anvil clicks I heat for 2 more 15 second cycles followed by one 12 second cycle before beginning my draw. Works great for me and I don't see any error messages.
 
fogbank,
  • Like
Reactions: mephisto

emily

Well-Known Member
I have one of the YLL IH V2 in black and here are some thoughts after using it a few times.

Pros:
-Solid metal build feels good in hand
-‘Power’ mode works really well
-Cheap
-Has a simple aesthetic
-Surprisingly small and stealthy

Cons:
-it’s annoying that it stops heating after a certain number of seconds, and you have to click the button again
-the power mode doesn’t go low enough for me. It’s pretty good but I can get bigger hits by setting it to the lowest power setting and then pulsing it slightly near the end
-why is the packaging so elaborate? Feels like a waste of everyone’s time and money

Overall this thing is a great upgrade from my Orion. I’m curious how reliable it will be considering how cheap it is.
 

kokolokokolokon

Well-Known Member
I have one of the YLL IH V2 in black and here are some thoughts after using it a few times.

Pros:
-Solid metal build feels good in hand
-‘Power’ mode works really well
-Cheap
-Has a simple aesthetic
-Surprisingly small and stealthy

Cons:
-it’s annoying that it stops heating after a certain number of seconds, and you have to click the button again
-the power mode doesn’t go low enough for me. It’s pretty good but I can get bigger hits by setting it to the lowest power setting and then pulsing it slightly near the end
-why is the packaging so elaborate? Feels like a waste of everyone’s time and money

Overall this thing is a great upgrade from my Orion. I’m curious how reliable it will be considering how cheap it is.
Ooh is it possible to see a image of the new ih?
Nice pros!
Do you know the exact size?

About the cons: seems like it has some cons of the old version. It was annoying to click the button to heat again. Does this one shut of the screen when you dont use it…and then you have to click the button to work again?

Can you regulate the height of the coil?
How about the battery?
 
kokolokokolokon,
  • Like
Reactions: hdd.heater
I have one of the YLL IH V2 in black and here are some thoughts after using it a few times.

Pros:
-Solid metal build feels good in hand
-‘Power’ mode works really well
-Cheap
-Has a simple aesthetic
-Surprisingly small and stealthy

Cons:
-it’s annoying that it stops heating after a certain number of seconds, and you have to click the button again
-the power mode doesn’t go low enough for me. It’s pretty good but I can get bigger hits by setting it to the lowest power setting and then pulsing it slightly near the end
-why is the packaging so elaborate? Feels like a waste of everyone’s time and money

Overall this thing is a great upgrade from my Orion. I’m curious how reliable it will be considering how cheap it is.
Any news? :)
I'm interested as well!
 
Top Bottom