Discontinued VapeXhale Cloud

[Jamesqc666]

hey guys i finaly receive my cloud!!!! I dont know if its broken but i just put a ez bowl half full wait 5 minute after the green ligth at max and then try it with a j hook for the first few bowl then i switch to my water bong for a couple more.I was able to get a couple of puff but really no big white smoke (very low ratio compare to a normal vaporizer).Is there a magic way are i should look back to a refund?

 

[green2brown]

hey guys i finaly receive my cloud!!!! I dont know if its broken but i just put a ez bowl half full wait 5 minute after the green ligth at max and then try it with a j hook for the first few bowl then i switch to my water bong for a couple more.I was able to get a couple of puff but really no big white smoke (very low ratio compare to a normal vaporizer).Is there a magic way are i should look back to a refund?

The Cloud can take up to 30 min to reach proper temp. Specific heat up times tend to vary greatly from one Cloud to the next. So yours may just need to sit a bit longer before it's ready. Unfortunately, the green light doesn't necessarily signify readiness.

 

[Purpl3_Haz3]

hey guys i finaly receive my cloud!!!! I dont know if its broken but i just put a ez bowl half full wait 5 minute after the green ligth at max and then try it with a j hook for the first few bowl then i switch to my water bong for a couple more.I was able to get a couple of puff but really no big white smoke (very low ratio compare to a normal vaporizer).Is there a magic way are i should look back to a refund?

The Cloud can take up to 30 min to reach proper temp. Specific heat up times tend to vary greatly from one Cloud to the next. So yours may just need to sit a bit longer before it's ready. Unfortunately, the green light doesn't necessarily signify readiness.

So, while you're waiting for the Cloud to actually stabilize temperature-wise (set it to somewhere around the neutral 12pm noon mark to get an idea of it's mid range temp)...make sure that your flowers are ground finely, and are very dry. They don't have to be powder fine by any means; a coarse grind or shred will work just fine. Ideally, the more surface area exposed while still allowing airflow through the load will produce the best vapor cloud results. Try to load, not pack, an ELB loosely, about halfway full or 1/3 of the way full. By the time all of this is done, and you've essentially let the entire Cloud unit begin to stabilize at operating temp, you can insert your ELB, and then using either a Hydratube, dry mouthpiece, or other glass utensil, give it another go!

 

[Kevdog420]

Your actual voltage could be anywhere between about 107 to 123. I'd select 110.

You sure about that? There was an early problem with a converter in a car, and a US version overseas also needs a converter. A regulator OTOH, is designed to even out the little ups and downs and maintain a constant voltage level, not convert it. That shouldn't be a problem. It's a helper. They help computers, cars, and power stations. With electronics, regulation is usually a good thing.

I was under the impression that 110v is for Jamaica and 120v was the United States and 127 for Mexico (atleast that's what it says on the box). I currently have it on 120v but yeah I'm not 100%

 

[jackstraw62]

hey guys i finaly receive my cloud!!!! I dont know if its broken but i just put a ez bowl half full wait 5 minute after the green ligth at max and then try it with a j hook for the first few bowl then i switch to my water bong for a couple more.I was able to get a couple of puff but really no big white smoke (very low ratio compare to a normal vaporizer).Is there a magic way are i should look back to a refund?

airflow is key. use medicine with lots of trichs

 

[Vessel]

I remember the good sugar trim worked really well with the cloud, better than you would expect. It's been awhile since I've tried my cloud, about 3 months. Before I was going a bit mad with everything, getting so fed up using the eq, there has been times when I just wanted to throw it against a wall. Compared to the cloud, it almost seems wasteful to use herb in another vape.


Before I contemplated loading up a elb and putting it in my broken Cloud + and heating the gong with a torch, Seriously. With the cloud breaking and the revamping of the company, this has all come at a bad time for me. By the time I do get my Evo, I will sadly be on a tolerance break for possibly a month or two.


Sad times for Vessel.

 

[mmafighterthe25]

Im about to hit the cloud through my atomizer for my sublimator lets see if makes cloud even smoother

 

[notmyrealUSERname]

Im about to hit the cloud through my atomizer for my sublimator lets see if makes cloud even smoother

Excellent idea! Can you try it twice- once with the atomizer cold and again with it at vaping temps?

I am Very intersted in this experiment! I'll try it with my ha/sv1/solo when I have a chance.

 

[mmafighterthe25]

Iv done it without atomizer Hot an was smoother didnt cough much u need nothing just stick joint in atomizer inhale works def smoothrr il try hot now

 

[stickstones]

I like where you're headed, mma...

 

[max]

We have the EVO anticipation thread - http://fuckcombustion.com/threads/the-cloud-evo-anticipation-thread.10875/page-6#post-486331 and the new EVO thread. One or the other is more appropriate for EVO posts, so let's keep this thread on topic and make sure the posts have something to with the original, and not just the EVO.

There seems to be a bonus for Cloud owners who buy the EVO in the elb dept. The Cloud elb's fit in the EVO with ease but aren't loose enough to come out if you upend the unit. I don't see any reason why they can't be used in EVO, so if you're upgrading and have a good supply of elb's already, they won't go to waste.

 

[mmafighterthe25]

Hitting cloud through sublimator atomizer does make it way smoother. I barely cough off huge dry hits that without would have me coughing like crazy. Hot or or cold works great

 

[stickstones]

you're using the atomizer cold?

 

[stonemonkey55]

Hitting cloud through sublimator atomizer does make it way smoother. I barely cough off huge dry hits that without would have me coughing like crazy. Hot or or cold works great

Can you show us the setup?

 

[mmafighterthe25]

you're using the atomizer cold?

I tried it both ways hot and cold an both make it crazy smooth dry hits

 

[John Lewus]

I tried it both ways hot and cold an both make it crazy smooth dry hits

Do you use the cloud to just pre heat the air or do you run an elb through the cloud? I am a bit confused at this setup.

 

[mmafighterthe25]

Just use cloud normal an just stick the glass joint down in atomizer I know its not air tight still works find just inhale

 

[John Lewus]

Just use cloud normal an just stick the glass joint down in atomizer I know its not air tight still works find just inhale

I don't have a sub so I am having a hard time imagining this. Can you post a pic?

 

[Madcap79]

Pics or it didn't happen. Ha!

 

[stygian16]

Happy double stack cloudy Sunday. That is all.

 

[Stu]

Modnote: Images removed at author request. Images depicted Cloud > Sublimator downstem > Gong joint.

Cool idea! I'm going to give this a try now.

 

[paracaps]

Cool idea! I'm going to give this a try now.

How was it Stu?
What your verdict on this unique combination?

 

[Stu]

How was it Stu?
What your verdict on this unique combination?

Too early for a verdict. For me the jury is still out.

I haven't tried using a heated atomizer yet, I've just been using it at room temperature so far. At first I thought that the hit felt smoother than usual. After several hits I tried the same setup sans atomizer and to be honest, I couldn't really tell a difference.

Then I had to stop and order a pizza.

I will try it tomorrow with a heated atomizer, but so far I haven't really noticed a big difference.

 

[Pappy]

30 day VXC rotation... No errata to report.

 

[mmafighterthe25]

I def love the mini elb, im using it all day