jbm
Not a Vapman “beta tester”
I would prefer the wider range of options that a 8mm stem would provide rather than a Vestratto-specfic option, thanks.
Tornado by Vestratto
- Thread starter Vapetothegrave
- Start date
-
- Tags
- vestratto
TedJones
Well-Known Member
Yeah, it’s pretty thin.. not ideal.
eyevape
👀
No matter how old it is, this habit will die immediately after your first serious heat lockYeah see that’s what I don’t like, I’d rather have it secure and use a tool to remove than have it slightly loose. Personal preference I suppose. Years of being a keen cyclist has drilled an odd sense of anxiety into me if things aren’t fully tight and there’s a rattleObviously not the same thing but old habits die hard!
The Tornado locks much harder than the Anvil, in fact you‘ll probably need pliers in addition to a hex key or wrench to unlock it. I also like all my devices rattle free, but after the second heat lock I never fully screwed in the bowl again.I love the idea of a hex key inside a donut magnet though
No, it's not a silly idea. I have been approached in the past by someone wanting the same thing made but for one of the previous Vestratto models. Unfortunately, the customer had a change of heart and it never made it off the drawing board. Perfectly feasible if it's something you'd like pursued.@ScruffyWoofers
I don’t know how feasible this is in a manufacturing sense but I’ve had an idea for a bowl remover that’ll help deal with the binding up until it cools that some are experiencing.
So it’s quite simple. This magnet is a popular accessory for the Anvil. It would basically be this with a slight tweak. In the centre of the magnetic surface would be a “nub” that is a hex key. It would magnetically attach to the bowl and the hex key part would then slot into the socket on the bowl. Would give much more leverage (is that the right term?) to unscrew the bowl with, and of course the magnet to quickly reset the clickers and help draw heat away from the oven and bowl. Maybe some ridges further up or a T shaped handle to give extra grip when turning too.
Perhaps it’s a silly high idea but thought I’d share
Hey Everyone, just jumping into the thread as a newbie.
Absolutely LOVING the tornado this device is epic, so much so that i produced my first How-To video / review ever
:
Really enjoying playing with this device but did have one heat thread lock that needed a hex key to open it back up, the rattle is annoying @eyevape but no where near as annoying as that lockup lol!
Absolutely LOVING the tornado this device is epic, so much so that i produced my first How-To video / review ever
:Really enjoying playing with this device but did have one heat thread lock that needed a hex key to open it back up, the rattle is annoying @eyevape but no where near as annoying as that lockup lol!
PrematureEvaporation
Well-Known Member
Oh bollocks. I did look at the photos of it after you mentioned and it did look a little thin. That’s a shame but I’m sure I’ll work something out.
Now you’re scaring me!No matter how old it is, this habit will die immediately after your first serious heat lock
I’ve had some utterly brutal heat locks with the original Dani v3 models, it was quite well known for it. If it’s as bad as that or worse then I totally understand now. A small hex key and magnet on a key chain might be a worthwhile investment then. That’s a shame they didn’t go through with it, I think it’s potentially a handy little tool. Well if it’s not something you’re planning to do as a general sale item then I think I’ll hit you up to get one made when I get my adapter off you in the future. Cheers man!
Anyone in Canada interested in the Tornado, I just ordered one with Sneaky Pete Canadian website https://vapenorth.ca/collections/hot-new-products/products/vestratto-tornado?variant=44239048048819
Cheers friends, greatly appreciate your assistance
In hindsight I probably should have just asked for the OD on the male joint component since that's the end I'm trying to match and would have tolerance control over.
But based on the dimensions you kind folks supplied for the Tornado head, I'm guestimating the male jointed base is ~9MM OD, with 1MM wall O rings, ~half recessed, which is then being compressed into the ~9.5-9.76 female head?
It's a new high surface area design I came up with based on fluid expansion.
Currently the design is 4" (100MM) long with over 8" squared of internal surface area.
The idea is to do something effective in function but simple enough to manage the price point.
I'll try to post some initial renderings briefly, I just need to finish up a few things.
Appreciate your interest FC!
Last edited:
Merci beaucoup frangin , je viens d'en commander une , je suis en France, j'ai hâte de la recevoir , bonne VAP
electrokho82
Well-Known Member
Ça risque d’être long, car Postes Canada est en grève illimitée. J’ai commandé plusieurs articles pendant le Black Friday, et tout est en pause jusqu’à la fin de la grève. J’espère qu’ils utilisent UPS ou DHL...
Mais quoi qu’il en soit, l’attente en vaut la peine : tu ne seras pas déçu avec le Tornado. C’est, selon moi, le meilleur vaporisateur sur le marché. Et je parle en connaissance de cause : j’ai une collection de 17 vaporisateurs, incluant des modèles phares comme le Tinymight 2 et le Venty, sans oublier des ball vapes comme le TIODW et le Ruby Twist.
Roffa
Well-Known Member
Yes. Big flame though
Nice
electrokho82
Well-Known Member
I only do one heat-up cycle with the Wand at the maximum setting. It takes 17-18 seconds for the first click and 21-22 seconds for the second click. If I wait until the second click, I can clear the bowl in a single draw.
letter never sent
reckoner
Absolutely. It’s not difficult to achieve one and done heat ups with a torch IMO. I don’t use the Tornado (or the Anvil) any other way. You don’t need a particularly large flame to do it either. I use the Ronxs/Cadrim or Blazer Firefox and have them both turned down pretty low.
TigoleBitties
Big and Bouncy
Yes, I can believe this. I don't think it would taste really great so this is why I don't attempt it but if you just want a lung buster to get lifted really quick it's doable.
I'm much happier to get 3-4 big tasty draws to finish a full bowl.
Last edited:
I'm not looking for taste from the Tornado. I have some amazing tasting vapes already. I want a big bowled, conduction, heavy hitting portable thay can survive being ran over. I want one huge cloud and the bowl to be spent in a hit. That would be awesome.
TigoleBitties
Big and Bouncy
I think you'll be pleased then. The Tornado is definitely capable of this but don't sleep on the flavor. It can be a very tasty vape too.
Roffa
Well-Known Member
It' s very versatile this way.
My dimensions are for the connection end of the Tornado (opposite end from bowl). Also my Tornado bowl dimensions are larger than the dimensions @ScruffyWoofers postedCheers friends, greatly appreciate your assistance
In hindsight I probably should have just asked for the OD on the male joint component since that's the end I'm trying to match and would have tolerance control over.
But based on the dimensions you kind folks supplied for the Tornado head, I'm guestimating the male jointed base is ~9MM OD, with 1MM wall O rings, ~half recessed, which is then being compressed into the ~9.5-9.76 female head?
It's a new high surface area design I came up with based on fluid expansion.
Currently the design is 4" (100MM) long with over 8" squared of internal surface area.
The idea is to do something effective in function but simple enough to manage the price point.
I'll try to post some initial renderings briefly, I just need to finish up a few things.
Appreciate your interest FC!
TigoleBitties
Big and Bouncy
Just picked up the adapters from @ScruffyWoofers in both 8 and 9mm. The first stem I'll probably try it on is the carbon fiber straight bore 9mm stem I use with my Stunner. I repurposed an Omni mouthpiece for it as well. If I can handle the vapor from the Stunner with this stem I think the Tornado will be fine. Maybe I'll throw a spiral in there.
I'll probably eventually pick up a wooden stem somewhere as well. I saw a really nice one from @Duba that I think was glass-lined.
I welcome anyone to post their 8/9mm stem suggestions and maybe weigh in on what the vapor is like through a stem?
I'll probably eventually pick up a wooden stem somewhere as well. I saw a really nice one from @Duba that I think was glass-lined.
I welcome anyone to post their 8/9mm stem suggestions and maybe weigh in on what the vapor is like through a stem?
Zuhdj
Charles Mingus
Anyone else's tracking not updated in over a week? My device has been in Dallas since last Thursday and hasn't been scanned since.
I know there's a strike for the Canada postal service rn but it went through customs and is in the US. Canada post workers aren't down here to strike. I'm peeved. Was really looking forward to having it for my week off. Fingers crossed it moves someday and isn't lost forever....
I know there's a strike for the Canada postal service rn but it went through customs and is in the US. Canada post workers aren't down here to strike. I'm peeved. Was really looking forward to having it for my week off. Fingers crossed it moves someday and isn't lost forever....