Lazy Lighting
Well-Known Member
Very nice! Are they the mouth pieces from vapefiend?Takin em for a walk on a cold winters day.
Discontinued The RBT Milaana (unregulated single 18650)
- Thread starter RastaBuddhaTao
- Start date
- Status
ArthurJ
Well-Known Member
DDave mods.
almost there
Well-Known Member
looks like the mp's from DDave
Lazy Lighting
Well-Known Member
Thanks!
ominosity
Well-Known Member
Have had my Milaana for 2 days now and loving it. Bought it to backup my two grasshoppers which are both dead (again). The flavour is immense and I feel like I’m getting the hang of it. Am having to stir throughout the bowl and wondering if mine might be set a little cooler as I don’t take my finger of the Button much and have to preheat for about 8 seconds even on a fresh battery. Also haven’t been able to match the cloud production I’ve seen on some videos in this post. I’m taking a while to get used to the huge airflow. All that said.... I love this vape!
TeeJay1952
Well-Known Member
Unless you are doing a session each load is cold when you pick it up. We use a lot of energy to get load up to temp. You are trying to find sweet spot where heater is supplying enough to vape but not so much to combust. You are trying to ride the wave as heater cools. No sense in wasting energy to heat what we are not inhaling. 
Lazy Lighting
Well-Known Member
The more you use it the more intuitive it becomes. I'm in love with this vape as well.
awmaster10
Well-Known Member
Got my Milaana the other day and found this adapter to use as a mouthpiece at a local head shop for $10. It cools the vapor as much as a medium/long stem because of the bend, but has an extremely small profile. Also should collect some reclaim at the end of the stem. Everybody should try this setup ASAP!
mikeb6109
Mike's Vaporizer Review
Got my Milaana the other day and found this adapter to use as a mouthpiece at a local head shop for $10. It cools the vapor as much as a medium/long stem because of the bend, but has an extremely small profile. Also should collect some reclaim at the end of the stem. Everybody should try this setup ASAP!
interesting..........looks more like a glass piece adapter of sorts, but I guess you found a better use for it!!
P.A.M.
Vapo Rising
@awmaster10 Very creative , awesome ! I like the profile it gives. Does it (must) fit facing the button side and away from the battery receptor.
awmaster10
Well-Known Member
Yep it can rotate 180 degrees clockwise so the mouthpiece is toward the camera hanging over the left side instead of the right side of the device. It only hits the device when the reclaim collecting part is facing directly at the battery compartment and terminal. (Aka about 180 degrees counter clockwise).
For battery safety it would be best to do that but the orientation shown makes the button access very natural. Overall the setup is great though and cools the perfect amount for the size. I’m sure it would shatter extravagantly if the device is dropped so consider buying a backup since they are only $10.
sickmanfraud
Well-Known Member
My suggestion for a bent stem for 18 mm vapes is this item from Amazon for $7.95 https://www.amazon.com/gp/product/B...fl_title_11?ie=UTF8&psc=1&smid=A2YWUIZGUW9D1Y
extra screens 20 screens for $12 total https://www.amazon.com/gp/product/B072V86X21/ref=ox_sc_sfl_title_1?ie=UTF8&smid=A3NL3HQJBHO5FT&th=1
EDIT: BTW if anyone has any @DDave pieces that seem too long, I have a solution. Buy yourself some Teflon tape (totally outside the vapor path) and make a couple of winds around the stem and you're in business.
extra screens 20 screens for $12 total https://www.amazon.com/gp/product/B072V86X21/ref=ox_sc_sfl_title_1?ie=UTF8&smid=A3NL3HQJBHO5FT&th=1
EDIT: BTW if anyone has any @DDave pieces that seem too long, I have a solution. Buy yourself some Teflon tape (totally outside the vapor path) and make a couple of winds around the stem and you're in business.
Last edited:
awmaster10
Well-Known Member
If you look up a couple posts to the sidecar style mouthpiece I am using, it is actually being held snug by teflon tape. Never gets near hot enough to be a problem for teflon and outside the vapor path.
Edit: I have been getting INCREDIBLE results with my current setup. I have compared with equally sized packs in my hydrobrick and Milaana and am getting much better flavor, longevity of flavor, and number of hits from the Milaana. I love it! The setup is the following:
- The mouthpiece pictured a few posts up on this page. Sidecar style with 18mm male on both ends.
- regular screen placed on the "rim" inside the 18mm joint like in a 7th floor vaporizer
- Arizer dome screen to cap the end of the joint
- Samsung 30q batteries
- Medium fine grind
- Pack 1/4-1/2 way up 18mm joint
This allows the bud to circulate and stir itself within the capped pack, and allows easy shaking which negates the need to open the pack up and stir. I have been getting extremely even extraction and a ton of hits per load. I appreciate that this vape can microdose really well but I appreciate even more the way it handles the medium sized loads I am used to from the hydrobrick.
The mouthpiece is absolutely perfect and gives good feedback without being hot at all, and it can be rotated to a couple really comfortable drawing positions.
The 30q batteries run cooler than some others, but have amazing life and honestly they make the learning curve easier because you can just preheat 5 seconds and draw at medium speed while riding the heat and not combust.
WOW. This thing has exceeded my expectations big time, and I hope everybody has tried out a setup like this or can at least find this style of mouthpiece at a local head shop.
Last edited:
grokit
well-worn member
I found some "FDA Epoxy, Medical Grade Adhesive, Two Part" on amazon...
Cheesequake
Free Men Don't Ask
Once you master the Milaana it is the best portable on the market IMO. As far as quality vapor goes anyway.
This is 6 huge incredibly tasty rips with no stirring. Screen is probably 1.25 inches down the stem with the dome facing where you put your mouth, so the load is pretty far away from the heater compared to stock setup. I find this allows much more even roasting with little effort. Absolutely amazing for huge waterpipe rips. Could probably fit about .5 comfortably the way it's setup but I probably have about .25 in this bowl and it isn't even close to full. It's a 18 to 14mm adapter and the inside is huge.
6 hits no stir
10 hits no stir
15 hits no stir
This is 6 huge incredibly tasty rips with no stirring. Screen is probably 1.25 inches down the stem with the dome facing where you put your mouth, so the load is pretty far away from the heater compared to stock setup. I find this allows much more even roasting with little effort. Absolutely amazing for huge waterpipe rips. Could probably fit about .5 comfortably the way it's setup but I probably have about .25 in this bowl and it isn't even close to full. It's a 18 to 14mm adapter and the inside is huge.
6 hits no stir
10 hits no stir
15 hits no stir
Last edited:
awmaster10
Well-Known Member
Cheesequake, I also have been putting the screen far down the joint and packing large packs. Very even extraction and tons of hits with no charring because of the added distance from the heater.
Jill NYC
Portable Hoarder
I find that when I push further down I have a hard time getting vapor (I do not use a water tool) and the herb never really gets utilized. I still get some nice flavor, and sometimes even a little medicated from it, but I have to use another vape to get all the goodies extracted.
@Cheesequake Does the herb ever get brown? Are you able to extract everything from it?
@Cheesequake Does the herb ever get brown? Are you able to extract everything from it?
Cheesequake
Free Men Don't Ask
Yeah you can make it as brown as you want and extract every bit. I was just trying to vape the whole bowl without stirring.
Edit:
Recorded a full session with the Milaana through my bubbler and edited out the parts where I'm stirring or not doing anything. ABV shot at the very end of the video.
Last edited:
- Status