Discontinued The Persei Vaporizer for herbs and concentrates.

itschad

Well-Known Member
Well, it isn't. Because there are only 4 over and 3 under on one, and 3 over and 2 under on the other. Reading 2 and 1.6 respectively, neither of which fires, neither of which has protruding wire.



I think this is simply the wrong size wire. Theres literally know way you're getting 1.5ohms with more than 2 wraps on this wire.
 
itschad,

invisiblefriend

Well-Known Member
Manufacturer
anyone have any advice on thur favorite wire to use ? -- for rebuilding -- esp the 3.7 & 7.4 -- my 3.7 I messed up a while a go ..(i used on a variable n went too high :( ! ) my bad !!! the 7.4 … I feel was just a bad luck situation - no ones fault at all --- it was always kinda loose feeling and the wire seems to have disconnected from the bottom of one side -- after just a few days -- I'm gunna see if i may have enough wire to re-attatch -- but doubt it - lol -- too tiny !

Yet I wonder if anyone has found titanium wire yet ? or any favorite wire out thur ? == thx my friends


Ill be asking Gary bout my next question --- :) -- I have been having a lil issue from day 1 with my Persei ---all around all super - I love it -- but it seems to have a mind of its own with a 3 flash situation -- usually no rymme or reason it blinx n turns off -- n just needs to be pressed again --- sometimes i think its being pressed 4 too long and then maybe a bad connection -- maybe too long during herc heat up ? --- but after experimenting with everything and every way -- it just seems to have a weird habit of blinking from time to time with no true reason ?
any one else have similar issue ---- its not crazy out f control -- but just buggy … ?
v3 ?

thx n everyone nay the eve !
 
invisiblefriend,

Vape Dr.

Well-Known Member
@invisiblefriend I have had that happen.
What I will do is unscrew the cart, hold the Persei button and screw the cart back on with the button depressed. Then it will work fine (Kiss or Herc).
This only happens every so often, but that seems to fix the quick flash syndrome.
Of course always make sure the connections are clean and do not over tighten the cart.
I hope this helps.
 

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
anyone have any advice on thur favorite wire to use ? -- for rebuilding -- esp the 3.7 & 7.4 -- my 3.7 I messed up a while a go ..(i used on a variable n went too high :( ! ) my bad !!! the 7.4 … I feel was just a bad luck situation - no ones fault at all --- it was always kinda loose feeling and the wire seems to have disconnected from the bottom of one side -- after just a few days -- I'm gunna see if i may have enough wire to re-attatch -- but doubt it - lol -- too tiny !

Yet I wonder if anyone has found titanium wire yet ? or any favorite wire out thur ? == thx my friends


Ill be asking Gary bout my next question --- :) -- I have been having a lil issue from day 1 with my Persei ---all around all super - I love it -- but it seems to have a mind of its own with a 3 flash situation -- usually no rymme or reason it blinx n turns off -- n just needs to be pressed again --- sometimes i think its being pressed 4 too long and then maybe a bad connection -- maybe too long during herc heat up ? --- but after experimenting with everything and every way -- it just seems to have a weird habit of blinking from time to time with no true reason ?
any one else have similar issue ---- its not crazy out f control -- but just buggy … ?
v3 ?

thx n everyone nay the eve !

The issue can be caused by a few things.

First the Persei has a time out function.

Second the Persei if the batteries are a seated lower or a damaged spring can cause the battery to engage and disengage the center contact under the top.


Third, due to not realizing many people have a collapsed spring and screw the batteries all the way up and cause the tops inside center pin to be pushed in and not allow the battery to properly make contact and since there is no compression in the spring then the batteries are static.

The whole Persei needs to be checked. Check everything I listed and we can narrow it down.
 

MaxVapor

The Professor
@THC SCIENTIFIC I see the Kiss Globes are back in stock! So my question is what can you tell me about the Nibbler GN:

The Nibbler GN is designed to work with our Kiss Globe series essential oil cartridges. It is a Necklace glass piece for our Kiss Globes or other globe type of cartridges. Made in the USA with high quality borosillicate glass.

How is this different than the Nibbler G? Photo maybe?

I will be ordering a KISS Globe soon and want to replace my Nibbler-X so just want to know my options.
 

invisiblefriend

Well-Known Member
Manufacturer
The issue can be caused by a few things.

First the Persei has a time out function.

Second the Persei if the batteries are a seated lower or a damaged spring can cause the battery to engage and disengage the center contact under the top.


Third, due to not realizing many people have a collapsed spring and screw the batteries all the way up and cause the tops inside center pin to be pushed in and not allow the battery to properly make contact and since there is no compression in the spring then the batteries are static.

The whole Persei needs to be checked. Check everything I listed and we can narrow it down.
thx my friend ---

I have been going by all advice --thk u - (honestly a few times with the herc -- it certainly could have timed out from my initial testing ! )

as far as other times where it happens -- it is just very intermittent -- usually after I press button -- a second goes by and the flashing starts but then I just go again and all good till it happens again …

I must be honest and say I have used this beauty ALOT …. but I use the core 97 % of the time ! so as far as batteries / spring ? -- I don't think that is it --

I know DR VAPE had some gr8 advice too and I will try that as well the next time :)

I will keep much better track of it and see if anything makes sense !
Again thx 4 all the gr8 advice !
much respect my friends

gd lookin THC SCIENTiFIC :)
 
invisiblefriend,
  • Like
Reactions: Vape Dr.

DaNi_DuB

Vapor Enthusiast
So I just dropped my Persei & cracked my ce-9 tank. Persei is unscathed & now I have reason to pick up a Protank 2 :D. It also made me think, why isn't there an accent piece for the Persei with a thing for a lanyard on it? It seems like the perfect complement.
 

syrupy

Authorized Buyer
So I just dropped my Persei & cracked my ce-9 tank. Persei is unscathed & now I have reason to pick up a Protank 2 :D. It also made me think, why isn't there an accent piece for the Persei with a thing for a lanyard on it? It seems like the perfect complement.

Psst. Undocumented feature. Unscrew the end cap and thread your lanyard through the two holes and re-attach to the tube. That endcap is plenty thick, and I can't see anything every messing it up, and the end cap is just cosmetic anyway.

Please tell me I'm not the only person who attaches a lanyard to the end cap.
 

SamuraiSam

Extraction Technician
I can't resisted and bought a brand new Persei + sr-74 to another nice menber, I'll receive it today I hope, not really sure to be able to use it hard before some months, but i get enough to do a good test!

I can't find any instructions about use of hash or kief in the sr-74?

Like for oil I think kief need a saturated coil (with oil)to work properly, isn't it?

Do you think it's not a good idea to saturate the coil with reclaim.....?

Thanks for your help
Reclaim will work okay, but will taste much worse than quality concentrate. I only tried kief on top of a coil that still had a "buffer" load in it of about .3g oil. Scooped the kief right on top and it vaped it well. However it makes a big mess, leaves behind a lot of coil-clogging carbon garbage and you will need to thoroughly clean your Herc before the next use. Soak the Ti coil in ISO for a long time then torch it.

Hi everyone, vapour beginner here. I have bought the Persei + SR-74 + The Core and am looking forward to trying it with extracts. However I am also on the market for a herb vapourizer. I am slightly confused by all the different attachments and models from the past and future. As far as I understand, the only way to vapourize herbs is through The Bender attachment. Although there was a herb specific top in the past that was scrapped? As well, the Vection and Duction are coming, but I haven't really found much information about them so I am wondering if I should wait for the new Vection/Duction from Persei for my herbal needs. Any and all input is appreciated.
You understand correctly, The Bender is a glass herb chamber for the Persei. It has great flavor and is not very portable. It's a luxury device and it sure tastes good. The old "8" top was shelved a long time ago and the "universe" cart also long gone. You can use a Hercules to vape herb if you want. It's better to load the herb on top of an oil soaked coil, though. To ease confusion about what is past and what is present simply visit www.w9tech.com and browse any product category. If you can buy it, it exists now. If it's not on the site, it's history.

The Vection/Duction is not "From Persei". (OK technically it's not "From" anyone yet as absolutely nothing about the unit has been announced. Consider it coming in the far-future, not coming soon.) You should wait for it if you also are waiting for self-driving cars or a home-sized nuclear fission reactor. The Persei is a model of vaporizer just like the Omicron is. The company who makes the Persei is Utopia Planitia Technologies or UP Tech.

Psst. Undocumented feature. Unscrew the end cap and thread your lanyard through the two holes and re-attach to the tube. That endcap is plenty thick, and I can't see anything every messing it up, and the end cap is just cosmetic anyway.

Please tell me I'm not the only person who attaches a lanyard to the end cap.
You don't want to see my double zip tie, belt loop attachment persei shorty
It's the epitome of macguyver....
 
SamuraiSam,
  • Like
Reactions: syrupy

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
@THC SCIENTIFIC I see the Kiss Globes are back in stock! So my question is what can you tell me about the Nibbler GN:

The Nibbler GN is designed to work with our Kiss Globe series essential oil cartridges. It is a Necklace glass piece for our Kiss Globes or other globe type of cartridges. Made in the USA with high quality borosillicate glass.

How is this different than the Nibbler G? Photo maybe?

I will be ordering a KISS Globe soon and want to replace my Nibbler-X so just want to know my options.


 

SkrACHIN

Well-Known Member
Since I received my black rod, I don't use my white rod !
Yes, it's a little bit less vapor, but the taste is much better IMHO
i found the opposite. used the black rod for a week or so but took so long to get the desired result. great if you want to use the persei for a long, slow session. but for me the "two-hit-quit-come-back-in-an-hour" method is the way to go. the white rod is the king with shatter. pair that with the core and it's happy time in fantasy land...

<iframe width="640" height="360" src="//www.youtube.com/embed/atC_8aTGRtM?feature=player_detailpage" frameborder="0" allowfullscreen></iframe>
 

Kingsmoke9

New Member
Oh I started like this but every time I filled this much it would just leak out the bottom holes and I refuse to clean it and recollect the fallen concentrate every 2nd day.

This is what I'm talking about.. Trial and error galore lol
Hey. Have you ever gotten the solution for this? I literally recollected .25g almost of wax. Just from the metal casing leaking out wax to the plastic. I'm using the 7.4v rod and a single coil sponge. Questions....when I add .5g to prime the herc after let's say boiling/cleaning it....just to prime it.....where does it go. And then I understand the concept of the oil pool on the sponge...but if you add .5 in the beginning....and you use it...doesn't it vape it? I'm just confused on the way to prime and load wax....and to stop the leaking. The reclaim is nuts. Also. I would like to ask if anyone knows how to perfectly reclaim all your wax from the herc? what steps do I clean this herc with to have it all reclaimed.... I was thinking an ever clear wash? Ziplock and ever clear and shake shake shake?
 
Kingsmoke9,

itschad

Well-Known Member
Hey people who rebuild their coils. Why do we not want our coils touching? How come all the ecig builds have their coil as a nice coherent almost solid stack?
 
itschad,

OB

Well-Known Member
Because it will short out the length of wire u used. The longer the wire the greater the resistance. So in doing that unless you have a high guage of wire (probably above 32g) it will make the resistance too low to function properly
 

itschad

Well-Known Member
Hey. Have you ever gotten the solution for this? I literally recollected .25g almost of wax. Just from the metal casing leaking out wax to the plastic. I'm using the 7.4v rod and a single coil sponge. Questions....when I add .5g to prime the herc after let's say boiling/cleaning it....just to prime it.....where does it go. And then I understand the concept of the oil pool on the sponge...but if you add .5 in the beginning....and you use it...doesn't it vape it? I'm just confused on the way to prime and load wax....and to stop the leaking. The reclaim is nuts. Also. I would like to ask if anyone knows how to perfectly reclaim all your wax from the herc? what steps do I clean this herc with to have it all reclaimed.... I was thinking an ever clear wash? Ziplock and ever clear and shake shake shake?


If you're loading .5 to prime and then another .5 on top of it, and you're using a single TI coil, then the issue is you're vastly overloading. A single TI coil takes about 0.25 to prime, and you should be able to vape happily from there.

to prime: Drop about 0.3 onto a brand new clean coil and put the mouth piece on. hold the button for 3 seconds then gently start pulling and release the battery for 3 seconds

repeat this 2 or 3 times then add another .2 or .3 to hit on. I find if you add more than .3 and your stuff isn't really stable, you have to be much more careful about cooling off


Because it will short out the length of wire u used. The longer the wire the greater the resistance. So in doing that unless you have a high guage of wire (probably above 32g) it will make the resistance too low to function properly

so if i want 5 over 4 under, or a more consistent stack of coil, I need to use a lower gauge then, right?

my issue is that reisistance is too high with the 28g. I can BARELY get 3 wraps and have a functional unit at 3.7v
 
itschad,
Top Bottom