ambertrichome
Well-Known Member
I’ve found that no huge difference in performance with non filled capsules, still functions great.What happens if I don't fully fill a capsule?
I’ve found that no huge difference in performance with non filled capsules, still functions great.What happens if I don't fully fill a capsule?
Well done sir, love itI've been dicking around with temp readings in my vapes and it's the Mighty's turn. I ran a probe down the stem, through the cooling unit and into a dosing capsule packed with abv. Set it to 390 and turned it on. For this first graph I decided to let it sit and see how long it took it to stop climbing after the display read 390. It keeps climbing since the probe is in the bowl and the Mighty is reading the heater below. This isn't very real life, mostly a 'let it sit' followed by three hits. The hits start when the curve starts climbing up and drops after that. By hits, I mean using a pump to draw air through the system. Later I'll get better at the air flow estimating what we as humans do. For now, though, I think the pump is a bit strong. The chart may change later when I make this adjustment. Here it is:
The following graph is more real life, as I started the simulated draws once it reached 390 like I always do. The bowl increased in temp until stabilizing just a couple of degrees below set, and then would drop when the draw stopped.
The bowl read near 290 when I started the first draw, and the temp quickly climbed to 370 and stabilized until I quit the draw, at which point it dropped to around 350 to rest until the next hit. The next four draws are repeats, but with the high and low temps increasing slightly each hit. On the fifth and final draw I let the pump go for a long time just to see. The Mighty was able to keep up, not even dropping 20 degrees in total.
Nice work, Sticks. Can you share with us the pump you are currently using? I've been trying to rig up a realistic hit simulator, but I'm not having much luck. I suck at getting things to suck it appears.I've been dicking around with temp readings in my vapes and it's the Mighty's turn. I ran a probe down the stem, through the cooling unit and into a dosing capsule packed with abv. Set it to 390 and turned it on. For this first graph I decided to let it sit and see how long it took it to stop climbing after the display read 390. It keeps climbing since the probe is in the bowl and the Mighty is reading the heater below. This isn't very real life, mostly a 'let it sit' followed by three hits. The hits start when the curve starts climbing up and drops after that. By hits, I mean using a pump to draw air through the system. Later I'll get better at the air flow estimating what we as humans do. For now, though, I think the pump is a bit strong. The chart may change later when I make this adjustment. Here it is:
The following graph is more real life, as I started the simulated draws once it reached 390 like I always do. The bowl increased in temp until stabilizing just a couple of degrees below set, and then would drop when the draw stopped.
The bowl read near 290 when I started the first draw, and the temp quickly climbed to 370 and stabilized until I quit the draw, at which point it dropped to around 350 to rest until the next hit. The next four draws are repeats, but with the high and low temps increasing slightly each hit. On the fifth and final draw I let the pump go for a long time just to see. The Mighty was able to keep up, not even dropping 20 degrees in total.
If it mini vibrates when coming near to the end of the session and has the boost function then it will be the latest version.How can I determine what version my Mighty is?
I want to ensure it's the latest version.
Thanks @stickstones !I've been dicking around with temp readings in my vapes and it's the Mighty's turn. I ran a probe down the stem, through the cooling unit and into a dosing capsule packed with abv. Set it to 390 and turned it on. For this first graph I decided to let it sit and see how long it took it to stop climbing after the display read 390. It keeps climbing since the probe is in the bowl and the Mighty is reading the heater below. This isn't very real life, mostly a 'let it sit' followed by three hits. The hits start when the curve starts climbing up and drops after that. By hits, I mean using a pump to draw air through the system. Later I'll get better at the air flow estimating what we as humans do. For now, though, I think the pump is a bit strong. The chart may change later when I make this adjustment. Here it is:
The following graph is more real life, as I started the simulated draws once it reached 390 like I always do. The bowl increased in temp until stabilizing just a couple of degrees below set, and then would drop when the draw stopped.
The bowl read near 290 when I started the first draw, and the temp quickly climbed to 370 and stabilized until I quit the draw, at which point it dropped to around 350 to rest until the next hit. The next four draws are repeats, but with the high and low temps increasing slightly each hit. On the fifth and final draw I let the pump go for a long time just to see. The Mighty was able to keep up, not even dropping 20 degrees in total.
Nice work - i just don't get completly how u ran the probe trough, i would have drilled a hole at the middle top of the cooling unit, so it could be drawn from like normal...I ran a probe down the stem, through the cooling unit and into a dosing capsule packed with abv
Hi everyone, I'm new to this forum and I just bought a new shiny mighty that I still have to (insert here equivalent of fire it up). I have one question: is it normal that just putting a very very little pressure on the display of the mighty, I can see very strange artifacts that vanish slowly after releasing pressure? Don't tell me it's a defective unit :/
Has anyone used e-liquid in their Mighty using a capsule with concentrate pad? I've treated myself to some CBD e-liquid and I'm not sure what temperature to use.... I was thinking of starting at about 180 C
Thanks @stickstones !
When you finished your vape testing, could you start a vape temp comparison thread? Personally, I'd love to see a comparison chart. I'm would be great to see a list of vapes with use and resting temps; especially comparing all of these hybrid vapes!
Don't want to create more work for you, though. Thanks again!!!
Nice work - i just don't get completly how u ran the probe trough, i would have drilled a hole at the middle top of the cooling unit, so it could be drawn from like normal...
And are u using 2 or 4 wires for the measuring probe? - 4 wires eliminate possible errors of the (temp changing) wire resistance...
Do you guys put the capsule in before or after the unit is heated?
Also, the screen in the CU, should i be using the fine or coarse screen if i am also using capsules?
And finally, any issues with using it upside down with the delta 3d WPA and capsules?
How can I determine what version my Mighty is?
I want to ensure it's the latest version.
Presumed known revision and improvement listing since release in approximate chronological order:
Changes to plastic temperature resistance and reinforcements around rim and casing of bowl
Change 1 minute timer to 2 minute timer
Revised design of power button to reduce premature failures.
Change rear label from raw painted foil to laminate layer label.
Change O-ring shades of light blue to dark blue to purple (different suppliers?)
Include 1x Capsule in box (and 8 capsule magazine in place of filling aid for Mighty Medic only) (2015?)
Added capsule caddy and Hygiene MP covers to website accessory section
Change rear label to different icon layout and further revised label material finish
Added additional haptic feedback function to signal timer shutdown
Added temperature boost function to power button (2016?)
Changed 2 minute timer to 3 minute timer
Changed packaging from Blue with Orange, to mainly White with Blue/Orange accents (2017)
Well, I got my mighty recently in July 2017, In the older primary blue box.. You guys forget the Mighty stands!! with out the orange pick trick.. But i noticed if you take out the orange pick from the bottom it doesnt stand..if you have the orange pick in normal as is, it will stand. Just a reminder.. Oh yea to confirm the power button is also boost button which u can set..I hear People says why do u need it but its really genius..You start at ur temp, tap it twice when u need it to finish it off, turn it off and next time it starts on your start temp.. I like it cuz you conserve on button pressing, also it does have timer/draw sensor in boost mode that it will bring it back to the temp you were at before boost mode.You could email the company with the serial number or box info for the most solid answer.
Alternatively,
I threw a simple list together a while back when there was a bit of confusion over what was a known update or when.
I've added anything new that I heard about and it might be helpful to see where your Mighty sits in this.
Basically if you got that new box with mostly white, I think that's the most up to date one right now!
The first few updates here are the most important imo, but a fully up to date Mighty is probably best if you can get it for the price you paid.
Maybe there are errors or things missing from this too?
If ur talking about wax..I personally like to "sandwich" it between bud.. I bought capsule caddies wit the pads inside the capsule which I tried but I still prefer "sandwich" method.. really kicks up ur bud..BUt im noobie her and Im sure some 1 here has some crazy concoction on how to do it insanely..FYI also "sandwich" I also felt it kept the CU cleaner too, just my opinion and Im someone that cleans my mighty every 7-10 days. (I need to charge it everyday)Day 4- really impressed with how this thing works and how the different temps have different effects.
just loaded up some critical plus for and did a whole capsule of about .1 at 365, great and clear.
last night i tried some grandpas breath at 404 and wow, was out soon after. not sure i can go higher than 390 until night time, especially with a indica. might try a high temp on a sativa.
have the delta 3d WPA coming to play with. I'm used to glass, so using this thing through a tube is very enticing. also have more capsules coming.
any tips for doing rosin in this thing?