kingofnull
ace
Dewaar joint is an inverted 14 or 18 mm joint as seen here:
Rather than sticking out, the 14 mm joint is recessed into the ash catcher.
The FC Bubbler by PlanetVape
- Thread starter PlanetHaze
- Start date
- Status
Dewaar joint is an inverted 14 or 18 mm joint as seen here:
Rather than sticking out, the 14 mm joint is recessed into the ash catcher.
Tweak
T\/\/34|<
A recessed joint, or a joint that is flush with the piece. Like in the image below.
Yeah I really dig there Bent neck Showerhead
Just wish the showerhead would sit down further into that can. What a waste of room.
And I can't make out the slits. Are they flame polished?
kingofnull
ace
Wow, why did they position the showerhead so high up?! It looks kind of ridiculous when you focus just on that area.
Edit: great price on that bubbler.
Edit: great price on that bubbler.
Tweak
T\/\/34|<
Very good point sir. Never thought of it that way. I was just thinking about how much bottled water I would go through, lol.Now to figure out how to get rid of that huge logo. Wonder if Sulfuric Acid would work?
And they even claim 5mm glass. I wonder what size bore that can is? That's a 14mm downstem so I'm guessing around 50mm?
Great Ideas everyone. The second prototype is already in production with the changes requested:
Based on feedback, here are the expected changes:
Sounds like votes are for the words
to be vertically placed on front of the downstem inside the can, f at the top and n at the bottom orientation with a low key, classy sandblasted appearance about this same size. The template to make the logos takes about 2 weeks to get made, so if this layout sounds good, then we can get it ordered now to reduce any further delays.
The Piranha showerhead is slightly larger in diameter than the last prototype to cause more collisions between bubbles and the side wall of the can for greater, smaller bubbles. There is no chug here, it purrrs nice and smooth, even using a restrictive vape.
Price is still holding at 159.95, this is a collaboration of design ideas from just the FC forum and the quality will be second to none. As soon as the next prototype arrives, we will post more pictures.
Peace and Love,
PV
Based on feedback, here are the expected changes:
- Borosilicate Glass – now 3.2mm thick Heavy Wall
- Piranha Showerhead diffuser
- Showerhead that is braced at the bottom, but with a wider weld area
- Showerhead slits cut as far back to glass downstem as possible
- Strong mouthpiece gooseneck connection at the body with right angle and shoulder
- Expansion chamber at bottom of gooseneck to prevent splashback
- Hexagonal base, around 4.75” in diameter makes it very stable even with a heavy vape on top
- Shortened Gooseneck length, about 9.5 inches tall total, can is about 4” high and about 60mm wide, vapor centric, minimal air space
- End of mouthpiece is slightly larger and flared for a more natural seal
Sounds like votes are for the words
The Piranha showerhead is slightly larger in diameter than the last prototype to cause more collisions between bubbles and the side wall of the can for greater, smaller bubbles. There is no chug here, it purrrs nice and smooth, even using a restrictive vape.
Price is still holding at 159.95, this is a collaboration of design ideas from just the FC forum and the quality will be second to none. As soon as the next prototype arrives, we will post more pictures.
Peace and Love,
PV
deadc0ffee
Inquisitive vaporist
That sounds fantastic! I can't wait to pick one up!Great Ideas everyone. The second prototype is already in production with the changes requested:
Based on feedback, here are the expected changes:
Should be finished in about a week.
- Borosilicate Glass – now 3.2mm thick Heavy Wall
- Piranha Showerhead diffuser
- Showerhead that is braced at the bottom, but with a wider weld area
- Showerhead slits cut as far back to glass downstem as possible
- Strong mouthpiece gooseneck connection at the body with right angle and shoulder
- Expansion chamber at bottom of gooseneck to prevent splashback
- Hexagonal base, around 4.75” in diameter makes it very stable even with a heavy vape on top
- Shortened Gooseneck length, about 9.5 inches tall total, can is about 4” high and about 60mm wide, vapor centric, minimal air space
- End of mouthpiece is slightly larger and flared for a more natural seal
Sounds like votes are for the wordsto be vertically placed on front of the downstem inside the can, f at the top and n at the bottom orientation with a low key, classy sandblasted appearance about this same size. The template to make the logos takes about 2 weeks to get made, so if this layout sounds good, then we can get it ordered now to reduce any further delays.
The Piranha showerhead is slightly larger in diameter than the last prototype to cause more collisions between bubbles and the side wall of the can for greater, smaller bubbles. There is no chug here, it purrrs nice and smooth, even using a restrictive vape.
Price is still holding at 159.95, this is a collaboration of design ideas from just the FC forum and the quality will be second to none. As soon as the next prototype arrives, we will post more pictures.
Peace and Love,
PV
kushcabbage
vapor nerd
really? show some love for fc why don't you, I wouldn't even mind it saying planetvape on it. That's like saying can I get those cool new nike shoes, but can leave off the check logo. Guess it's in the same boat as de badging cars.
Jeppy
Pure Vaporist
LHS, have lots of plain glass. This is the FC bubbler. It's going to have 'something' on it to distinguish it as such. 'Fuck combustion' on the inside of the can and on the downstem is really very conservative.
stickstones
Vapor concierge
I think the logo on the downstem is classy
GOATPUSSY
Active Member
Classy is good. Seen way too many awful and badly used logos in my day. Really quick way to ruin the beauty of a nicely designed piece.
Im hopeful this one will be good.
deadc0ffee
Inquisitive vaporist
My optimism is about at its limit
(I mean that in a good way- tons of optimism, not I'm running out)
Progress
'Socratic Existentialist, MD'
I like all of this. I didn't quite understand "showerhead slits cut as far back to glass downstem as possible", but if it makes fizzy tiny bubbles that slosh & churn...
I am disappointed that the FC/PV bubbler does not have a tiny troll named Cannigan who changes the strain of your herbs upon request and rematerializes freshly cured herbs out of spent ones.
Version 2.0? 
Giant Robot
Well-Known Member
I've been watching this beauty develop in lurker mode but my excitement is building as well. I just wanted to add my $.02 and say how proud I am of this community effort and special thanks and props to the artists that are bringing this to life! I'm obviously hoping I'll be able to land one as well. I had been keeping an eye out for a new Mobius Dewaar Bub with Matrix but this just seems more special and personal to take part in. Bah, who am I kidding, I'll probably end up getting both! (It's not my fault, my Cloud gets lonely)!
Cheers,
Giant Robot
Cheers,
Giant Robot
StonedMMA
Active Member
What he just said!
placetime
Well-Known Member
Wasn't that part of the plan for 2.0 of the Zapbubbler before trouble started in Zapville?I am disappointed that the FC/PV bubbler does not have a tiny troll named Cannigan who changes the strain of your herbs upon request and rematerializes freshly cured herbs out of spent ones.
Adobewan
Well-Known Member
Sounds like votes are for the wordsto be vertically placed on front of the downstem inside the can, f at the top and n at the bottom orientation ...
Peace and Love,
PV
Seriously, you're going to spell out "Fuck" on the piece?
How the heck are we supposed to use this in church?
SD_haze
Well-Known Member
- Status